Transrotor Artus Manual
1.
Transrotor
Artus
Set up instruction
Reprint prohibited
Copyright Räke Hifi Vertrieb
RÄKE HIFI/VERTRIEB GMBH, IRLENFELDER WEG 43, D-51467 BERG. GLADBACH
Tele on 02202/31046, Tele ax 02202/36844, E-Mail transrotorhi i@t-online.de
2.
Set up carrier unit
To get an overview
unwrap all packages
and put single parts as
shown on the following
fotos.
1.
Assembly – please pay
strict attention for the
chronological order.
2.
All parts must be taken
carefully into one’s
hand.
3.
3.
Make sure to avoid any
banging together of the
parts.
4.
Please follow the well
proven instruction of
the set up procedere.
5.
Allways wear the
delivered cotton gloves
during set up.
This set up takes about
4 h.
6.
4.
3 legs are screwed to the
underside of the ground
panel.
7.
On the top of the ground
panel you’ll find labels to be
shown up.
8.
5.
Screw in threaded
bolts.
9.
10.
6.
Mount one leg to the
lower right.
2nd leg one hole upper
left.
11.
Screw with spacers.
12.
7.
Screw in the 3rd leg.
13.
3 legs are now
triangular arranged.
14.
8.
The table is carefully
set upright.
15.
Now the feet of the 3
legs are screwed out by
8 mm.
16.
Put the coasters under
the 3 feet.
17.
9.
Now the device sits on
the coasters.
18.
Now screw the other 5 legs.
19.
Put the coasters under the legs.
20.
10.
Only 3 legs out of 8
must stand on the
ground floor. (foto 18)
The device is
horizontelly aligned by
these 3 legs.
21.
The level is used
laterally and
longitudinally.
22.
11.
The device is now only
aligned on 3 legs and the
other 5 legs are
free-hanging.
23.
The toolbox is put on
centered.
24.
12.
Open the toolbox.
(Screw out 2 screws)
25.
Take out the tool.
26.
13.
Close the toolbox.
Screw in 4 threaded brass
bolts.
27.
28.
14.
Put the black panel onto
the threaded brass bolts.
Watch the labels
(front and top).
29.
Screw in all 4 Allen
bolts
.
30.
15.
Tighten screws slightly
with Allen key.
31.
Put the final caps onto
the 4 threaded brass
bolts.
(fotos 27 & 28)
32.
16.
4 final caps screwed.
33.
Screw in 4 threaded
brass bolts into the black
panel.
34.
17.
The eggiplates are put
onto the threaded brass
bolts.
35.
The outer line of the
eggiplates should be
aligned with the spacers
below for optical
reasons.
A spacer is put onto the
carrier bolt.
(front left)
36.
rear
leftright
front
leftright
18.
Screw tightly the carrier
bolt with the awl.
37.
Rear on the right a
carrier bolt with ceramic
ball is screwed by an
awl.
Don’t forget the spacer!
38.
rear
leftright
front
leftright
19.
Mount the alignment
bolts front right and left.
Put off the alignment
cap from the bolt.
39.
Now screw the
alignment bolt on the
eggiplate.
40.
The curved outer line of
the eggiplate should be
aligned with the spacers
below for optical
reasons.
41.
20.
With the use of an awl
the alignment bolts are
tightened.
42.
Put the alignment bolt
onto the spacer.
43.
The alignment cap is
now screwed.
44.
Table of contents
