TREND IQXIO User manual

IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020 1
Installation Instructions
IQXIO
I/O Expansion Module
Important: Retain these instructions
These instructions shall be used by trained service
personnel only. If the equipment is used in a manner not
specied by these instructions, the protection provided by the
equipment may be impaired. https://partners.trendcontrols.com
GB DE DK FIES FR
IT NL NO RU
PL SE
32349383-001
1Dimensions
123458
69
-1
-2 -4 -8
1
7
2
3 4 5 6 7 8
ON
ADDRESS
10 11 12 13 14 15 16
CC
1 2 3
C
4520V
AUX
20V
AUX
CC
6 7 89
0 10V 0 10V 0 10V
0 10V 0 10V
1 2 3 4 5 6
A
-
O
-
H
1 2 3 4 5
XIO/20
DO AO
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
0V 0V 0V
012345
AB
C
14
5
13
4
C
12
3
11
2
C
10
1
24V
AUX
1 2 1 2
0 10V 0 10V
A
-
O
-
H
XIO/7
DO AO
3 INSTALLATION
1 BOX CONTENTS 2 STORING
It is recommended that the installation should comply
with the local electrical safety installation practices (e.g.
HSE Memorandum of Guidance on Electricity at Work
Regulations 1989, USA National Electric Code).
CONTENTS
1 Box Contents.................................................................1
2 Storing ...........................................................................1
3 Installation .....................................................................1
4 Field Maintenance.........................................................8
5 Disposal.........................................................................8
6 China Hazardous Substance Table ..............................8
Labels used on IQXIO
24 Vac AUX
output connector
20 Vdc AUX
output connector
Supply inputs for
digital outputs
n
Digital output
connector (DO)
Universal input
connector (UI)
0 10V
Analogue output
override level
C
n
n
Universal input/
output connector
(UI/AO)
Hand, o󰀨, auto
switch
Address switch
Power indicator
Status indicator
1 2 3 4 5
61 2 3 4 5
DO AO
Output status
indicators
Any connected devices must be insulated from mains by
reinforced insulation.
IQXIO
Installation Instructions
(TG201447)
I/O Connector (x2)
HO
2
+65°C
(+150°F)
5
-20°C
(-4°F)
95%RH
Note: For temperatures below 0°C (32°F) special care must be
taken that there is no condensation on or within the unit.
135 mm (5.32”)
146 mm (5.75”)
60.4 mm
(2.38”)
130 mm (5.12”)
44.5 mm
(1.75”)
85 mm (3.35”)
96 mm (3.78”)
WARNING Removal of cover exposes dangerous
voltages.
WARNING To reduce the risk of electrical shock or re
do not interconnect the output of di󰀨erent Class 2 circuits.

2 IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020.
IQXIO Installation Instructions
2Mounting Requirements
3 INSTALLATION (continued)
IO/20
IO/20
HO
2
+55°C
(+131°F)
5
-20°C
(-4°F)
95%RH
IO/20
Caution: Do not mount in areas where acid fumes or other
deteriorating vapours can attack the metal parts of the
controller, or in areas where escaping gas or other explosive
vapours are present.
IO/20
Note: For temperatures below 0°C (32°F) special care must
be taken that there is no condensation on or within the unit.
IQX12 Installation Instructions
(TG201446)
IQX12 /..
IQX12P/..
IO/20
IO/20
IO/20
IQXIO/20, IQXIO/7 Modules
IP20
IQX12 Controller

IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020 3
Installation Instructions IQXIO
4Mount Unit
3Determine Module Interconnections and Power Supplies
3 INSTALLATION (continued)
XIO/7
IO/20
IO/20
IO/20
1
2
Fit end stop if
mounted on
vertical rail
4 x M4 (No.8)
Or: Secure using screws and xings
117 mm (4.69”)
120 mm (4.72”)
Either: Clip on to TS35 DIN Rail
IO/20
Connect module to controller
(if using direct connection)
IO/20
Connect module to controller
(if using direct connection)
67 mm (2.64”)
“click”
Remote Connection
Additional or remote modules require a separate power
supply (see step 6) and be interconnected via an I/O Data
Bus cable (see step 5). All supplies must be connected
to the same building’s earth ground plane.
Direct Connection to Controller
Up to 3 modules can be connected
directly to the controller depending on
module type and power supply loading.
Power
Supply
50 VA maximum
IQ X12
Controller
IQXIO/20
Module
IQXIO/7
Module
IQXIO/20
Module
IQXIO/7
Module
I/O Data Bus I/O Data Bus
Power
Supply
Power
Supply
Maximum overall bus/cable length = 40m (131 feet)
Maximum 8 Modules, up to 160 points (depending on controller licence)

4 IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020.
IQXIO Installation Instructions
6Connect Power (if required)
!
5Install I/O Bus Cable(s) (if required)
IO/20
3 INSTALLATION (continued)
Important: Where multiple devices are powered from
a single transformer, the same side of the transformer
secondary must be connected to the same power input
terminal in each device.
Supply voltage: 24 Vac (20 to 30 Vac) 50/60 Hz
Supply power: 35VA (IQXIO/20 module only)
15VA (IQXIO/7 module only)
100VA (module and loads).
Digital Output Supply
(see step 8)
I/O Module Supply
100 VA
maximum
35 VA for IQXIO/20 module
15 VA for IQXIO/7 module
X1
XX12+≤65 VA (IQXIO/20)
+≤85 VA (IQXIO/7)XX
12
X2
The supply must include a suitably rated switch in close
proximity and be clearly marked as the disconnecting
device for the unit. Do not position the equipment so that the
disconnecting device is di󰀩cult to operate.
Terminal size: 2.0 to 1.0 mm2(14 to 18 AWG).
Terminal screw torque: 0.4 to 0.5 Nm (3.5 to 4.4 lbf-in).
Recommended cable: 2.0 mm2(14 AWG).
Power supply cable must have maximum operating
temperature of 80°C or greater. For UL rating the input power
connections must be made using 18 AWG or larger wire rated
at least 90°C (194°F).
O
I
DO NOT SWITCH ON POWER
For UL rating the
transformer must
be class 2 rated.
*If the power supply
is not current-limited,
an external 4A fuse
or circuit breaker
must be tted.
This equipment
must be earthed
(grounded)
*
I/O Data Bus
(see step 5)
Terminal size: 2.0 to 1.0 mm2(14 to 18 AWG).
Terminal screw torque: 0.4 to 0.5 Nm (3.5 to 4.4 lbf-in).
Recommended cable: Screened twisted pair.
Power Supply
(see step 6)
IQ X12
Controller
IQXIO
Module
IQXIO
Module
IQXIO
Module
Connect screen at end
nearest controller only
Data +
Screen
Data –
0 V
24 V
Line
Voltage
GND
100 VA max.
24 Vac

IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020 5
Installation Instructions IQXIO
7Connect Universal Inputs / Outputs (if required)
IO/20
3 INSTALLATION (continued)
Terminal size: 2.0 to 1.0 mm2(14 to 18 AWG).
Terminal screw torque: 0.4 to 0.5 Nm (3.5 to 4.4 lbf-in).
Caution: Do not connect ‘C’ (0V) terminals to earth (ground).
Thermistor / Resistive input
Current input
Voltage input Volt-free / Digital input
nn
nn
nn
ensure correct
polarity
S
+
-
n
nn
0 to 10 Vdc
S
n
nn
Externally powered
External
Power
Supply
ensure correct
polarity
S
n
nn
Loop powered (using 20 Vdc AUX output supply, 100mA maximum)
ensure correct
polarity
Common C terminal is linked
internally to AUX supply common -
no additional connection is required
volt free
contact
open
collector
n
nn
ensure correct
polarity
logic
circuit
330 μA
TTL /
CMOS
0V
3
11
5
4
22
IN 0V IN 0V
IN 0V IN 0V
0V IN
0V IN 0V IN
29 13
30 14
31 15
32 33 34 35 36
C
14
5
13
4
C
12
3
11 5
22
CC
10 4
11
123458
69
7
10 11 12 13 14 15 16
CC
1 2 3
C
4520V
AUX
20V
AUX
CC
6 7 89
Input Connection Examples
Output Connection Example
Universal Inputs (UI)
I/O signal types are dened in controller conguration
0 to
300kW
e.g.
20kNTC
PT1000
Output Type Load
0 to 10 Vdc, 10 mA max. ≥1kW
4 to 20 mA ≤550W
XIO/7
IQXIO/20 (9 channels)
123456
CC
1 2 320V
AUX
IQXIO/7 (3 channels)
Universal Input/
Output (UIO)
IQXIO/20 (5 channels) IQXIO/7 (2 channels)

6 IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020.
IQXIO Installation Instructions
8Connect Digital Outputs (if required)
IO/20
XIO/7
3 INSTALLATION (continued)
Terminal size: 2.0 to 1.0 mm2(14 to 18 AWG).
Terminal screw torque: 0.4 to 0.5 Nm (3.5 to 4.4 lbf-in).
Output Type Solid-State Relay
Current per Channel 1.5A* continuous;
3.5A inrush for 100 ms.
* subject to 100VA limit via terminal B
on IQXIO/20 module.
Voltage Range: As supply source (see below).
A1A3B5
A2A4B6
+++
+++
–––
–––
17 18 19 20 21 22 23 24 25 26 27 28
0V 0V 0V
123456
AB
24V
AUX
n
n
n
n
n
n
Or: from an additional external source(s)
Either: from AUX output
Caution: Do not connect ‘0V’ terminals to earth (ground).
Connect Output Devices
Connect Output Power Supply
Output Signal Options: Binary (on/o󰀨);
PWM (pulse width modulation)
IQXIO/7 = 85VA maximum
IQXIO/20 = 65VA maximum
(see step 6)
A1
B2
+
+
–
–
78910 11 12
0V
12
AB
24V
AUX
IQXIO/20 (6 channels)
IQXIO/7 (2 channels)
Power
Supply
24 Vac (20 - 30Vac)
GND
terminal A =
72 VA max.
terminal B =
100 VA max.
Module Supply

IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020 7
Installation Instructions IQXIO
9Set Module Address(es)
10 Congure the IQX12 Controller and IQXIO Modules
3 INSTALLATION (continued)
All modules must be given a unique address between 1 and 8
before applying power. Set switches 1, 2, 4 and 8 to be
ON hor OFF ias shown in the table below:
Module
Address 1 2 4 8
Module
Address 1 2 4 8
0 (o󰀨) i i i i 5h i h i
1h i i i 6i h h i
2i h i i 7h h h i
3h h i i 8i i i h
4i i h i
Important: Addresses must be set prior to commissioning.
IQX Conguration Manual
(TE201448)
IO/20
XIO/7
-1
-2 -4 -8
1
2
3 4 5 6 7 8
ON
ADDRESS

8 IQXIO I/O Expansion Module Installation Instructions TG201447 Issue 1, 24-Mar-2020.
IQXIO Installation Instructions
TR CU Certication
Please send any comments about this or any other Trend technical
publication to [email protected]
© 2020 Honeywell Products and Solutions SARL, Connected Building Division. All rights reserved. Manufactured for and on behalf of the Connected
Building Division of Honeywell Products and Solutions SARL, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control
Systems Limited.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation
to notify any person of such revisions or changes.
Trend Control Systems Limited
St. Mark’s Court, North Street, Horsham, West Sussex, RH12 1BW, UK. Tel: [phone], www.trendcontrols.com
4 FIELD MAINTENANCE
The IQXIO requires no routine maintenance.
6 CHINA HAZARDOUS SUBSTANCE TABLE
部件名称
Component Name
有害物质
Hazardous Substances
铅(Pb)
Lead (Pb)
汞(Hg)
Mercury (Hg)
镉 (Cd)
Cadmium (Cd)
六价铬 (Cr6+)
Chromium VI
Compounds
(Cr6+)
多溴联苯 (PBB)
Polybrominated
Biphenyls (PBB)
多溴二苯醚
(PBDE)
Polybrominated
Diphenyl Ethers
(PBDE)
接线端子
Terminal Block
X O O O O O
导轨
Bus Bar
X O O O O O
螺丝
Screws
X O O O O O
印刷线路板
PCB
X O O O O O
本表格依据
SJ/T 11364
的规定编制。
This table is prepared in accordance with the provisions of SJ/T 11364.
O
表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572
规 定 的 限 量 要 求以下。
Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement
of GB/T 26572.
X
表示该有害物质至少在该部件的某一均质材料中的含量超出
GB/T 26572
规定的限量要求。
Indicates that said hazardous substance contained in all of the homogeneous materials for this part is above the limit requirement
of GB/T 26572.
未列入表内的其他部件，皆不含任何超出限量要求的限制使用物质。
All other components, not listed in the table, do not contain restricted substances above the threshold level
5 DISPOSAL
!
WARNING: Contains no serviceable parts. Do
not attempt to open the unit. Failure to comply may
cause damage to the unit.
WEEE Directive:
At the end of their useful life the packaging and
product should be disposed of by a suitable
recycling centre.
Do not dispose of with normal household waste.
Do not burn.