TREQ ACE User manual

TREQ ACE
WITH SIMUCUBE FRONT MOUNT
INSTRUCTION MANUAL
The setup of your rig is very dependent on body type, personal seating preferences and the
equipment you own, but to give you a head start, we included a setup scheme on the last page.
REQUIRED TOOLS:
5-6 mm

GENERAL INSTRUCTIONS
www.treq-sim.com
123
Click!
123
Break!
REQUIRED TOOL:
The easiest way to mount the click-in-nuts, is to slide them in from one side of the profile. But
don't worry if you need to put in a click-in-nut in a profile which has both ends already closed: it
is also possible to push them in the T-slot anywhere you like!
The corner brackets feature 4 little hooks to stop the bracket from rotating once it is mounted
on a profile. But on some places of the rig these corner brackets are placed on a 90° angle of
the T-slot. In these situations it is recommended to break off 2 of the hooks, which is easily
done with a screwdriver or a plier.

1
2x 2x 2x
Profile 16040 L=1185
Profile 4040 L=478 Profile 16040 L=500
2x
Profile 4040 L=500
1x
Profile 4080 L=478
www.treq-sim.com
Profile 12040 L=740
2x
Pedal Bracket Left
1x 1x
28x
Corner 4040
Front Mounting Plate 580mm
1x
Cover 4040
4x 4x
Cover 12080
Pedal Bracket Right
4x
Cover 16080
2x
Mounting Plate
Clamp M8x20
4x

54x
Click-in Nut M8
www.treq-sim.com
48x
M8x16
18x
2
Corner Cover
28x
8x
2
2
M8 BOLTS AND WASHERS
M8x25 (Socket Head) Black 12
M8x20 (Socket Head) Black 20
M8x20 (Sunken Head) Black 4
M8 Washer 18
Nut M8 8
Bags with bolts, nuts and washers:
CABLE MANAGEMENT
M4x12 Screw 5
M4 T-Nut Click-in-Nut 5
Cable Binder 5 You can use these on any place you like. Either
inside the profile slot (just turn the bolt through
the tape), or by pasting them.
RUBBER FEET
M5x12 (Socket Head) 4
M5 T-Nut Click-in-Nut 4
Rubber Foot 4
STEERING WHEEL / PEDAL
MOUNTING
M6x12 Screw 2
M6x16 (Socket Head) 4
M6x20 (Socket Head) 4
M6x25 (Socket Head) 2
M6 Washer 6
M6 T-Nut Click-in-Nut 4

3
www.treq-sim.com
M8
(16x)
M5
(4x)
M5
(4x)
Profile 16040 L=1185 (2x)
2
(4x)
M5x12
(4x)

3
4
www.treq-sim.com
M8
(12x)
M8x16
(16x)

5
6
www.treq-sim.com
Profile 4040 L=500 (2x)
M8
(4x)
M8x16
(8x)

7
8
www.treq-sim.com
Profile 12040 L=740 (2x)
M8
(8x)
M8
(16x)

9
10
www.treq-sim.com
M8x20
(Black)
(2x)
M8
(2x)
Assembly of Pedal Bracket
M8x20
(Black)
(6x)
Profile 8040 L=478 (1x)
Profile 4040 L=478 (2x)
Assemble the Pedal Bracket on Frame
Hand
greep (4x)

11
www.treq-sim.com
OPTIONAL: Some pedals, like Thrustmaster or Logitech, have threaded holes on the
bottom of the pedal base. To mount these type of pedals, please use the spare corner
brackets. Mount 1 side to a pedaldeck-profile and the other to the pedals.
For Fanatec or Heusinkveld pedals you can use click-in-nuts and mount them ‘from the
top’.

Mount both ‘Mounting Plates’ to the upright profiles of your rig.
12
13
www.treq-sim.com
M8x25
(8x)
M8x20
(8x)
Break!

14
15
www.treq-sim.com
With the spare M8x25 bolts and washers, you can mount your wheelbase.
Place all covers on both the profiles as well as the corner brackets

16
www.treq-sim.com
Setting up your rig in the perfect way can take a lot of time and adjustments. Everybody is
different, and with the enormous amount of sim racing gear available, it is impossible to draw you
the perfect seating position. But this page should help you when tightening all the bolts for the
first time. After you’ve built it up like this, you can then fine tune it to your own preferences.
Body length: 160 cm
A: 50 cm
B: 60 cm
C: 73 cm
When first building your rig, we recommend putting S on 31 cm. Don’t tighten
the bolts of the steering rack too much, because there is a big chance you’re
going to adjust it after you mount a steering wheel.
Body length: 180 cm
A: 55 cm
B: 65 cm
C: 78 cm
Body length: 200 cm
A: 60 cm
B: 70 cm
C: 83 cm