Tripp Lite DWM3750S User manual

1
Owner’s Manual
Full Motion
Flat Screen Wall Mount
MODEL: DWM3750S
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All rights reserved.
75 x 75
100x100
200x200
400x400
50”
MAX 20 kg
(44 lbs)
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an ISOBAR6ULTRA
surge protector—a $100 value!
www.tripplite.com/warranty
15-09-382-933501-EN.indd 1 10/7/2015 10:12:50 AM

2
NOTE: Read the entire instruction manual before you start installation and assembly.
Warranty and Product Registration
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit www.tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability, with
basic building experience and a full understanding of this instruction manual.
• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the
items, greatly reducing their holding power.
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
15-09-382-933501-EN.indd 2 10/7/2015 10:12:51 AM

3
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.
Wallplate
5 mm Hex Key
3 mm Hex Key
Extension Arm VESA Plate Adapters (x4)
Spring Arm and VESA Plate
6 mm Hex Key
Tension Screw (x2)
M4X12 (x4)
M6X12 (x4)
Wallplate Covers (1 Pair) Level (x1)Decorative Cap (x2)
M8 Hex Nut (x8)
M4X30 (x4)
M6X30 (x4)
Spacer (x4) Anchor Bolt (x3) Concrete Anchor
(x3)
M5X12 (x4)
M8X16 (x4)
M5X30 (x4)
M8X30 (x4)
15-09-382-933501-EN.indd 3 10/7/2015 10:12:51 AM

4
1a. Mount on Wood Stud Wall
3
Mark the exact location of the
mounting holes
Screw the wall
mount onto
the wall
Drill pilot holes
WARNING
• Make sure that mounting screws are anchored into the center of the studs.
Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
Find a wood stud location for
mounting the wall mount
12
30 mm
(1.2”)
3 mm
0.2”)
Insert the two plastic covers
on wall plate for decorative
appearance.
Anchor Bolt
15-09-382-933501-EN.indd 4 10/7/2015 10:12:52 AM

5
1b. Mount on Solid Brick or Concrete Block
Insert the two plastic covers
on wall plate for decorative
appearance.
WARNING
• When installing wall mounts onto a concrete masonry unit (also known as a CMU or
“cinder block”), verify that the actual concrete thickness is at least 35 mm (1 3/8”)
in order to hold the concrete anchors. DO NOT DRILL INTO MORTAR JOINTS! Be sure
to mount the wall mount with the included concrete anchors and anchor bolts onto
solid sections of the blocks. The solid sections can generally be found 25 mm (1”)
toward the middle of the block from either end. An electric drill on a slow setting is
suggested to drill the hole rather than a hammer drill so as to avoid breaking out the
back of the hole when entering a hollow section.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
Screw the wall
mount onto
the wall
Drill pilot holes
2
Find and mark the exact
location of mounting holes
1
Concrete Anchor
Anchor Bolt
50 mm
(2”)
8 mm
0.31”)
15-09-382-933501-EN.indd 5 10/7/2015 10:12:53 AM

6
2. Attach Extension Arm onto Wallplate
3. Attach Spring Arm onto Extension Arm
4. Install VESA Plate
Attach larger displays using VESA Plate
Adapters and M8 Hex Nuts.
Insert the Tension Screw through
the Wallplate’s bottom hole up
toward the Decorative Cap.
Insert the Tension Screw through
the Extension Arm’s bottom hole
up toward the Decorative Cap.
Note: Firmly secure the VESA plate to the display
using the appropriate screws, washers and spacers
(if necessary).
Do not over-tighten screws.
M4X12
M4X30
M5X12
M5X30
M6X12
M6X30
M8 Hex Nut
Tension
Screw
Tension
Screw
Spacer
15-09-382-933501-EN.indd 6 10/7/2015 10:12:54 AM

7
5. Attach VESA Plate with Display to Arm Assembly
6. Tension Adjustment
Using an assistant or mechanical lifting equipment, lift the display with attached VESA plate. Align the VESA
plate slide-in adapter with the spring arm connector and slide the unit onto the Arm Assembly 1. Secure the
VESA Plate with Display to the Arm Assembly by tightening screw on the Spring Arm 2.
To adjust the height tension on the Spring Arm, use a 6 mm Hex Key and turn clockwise to reduce tension for
lighter TVs or counter-clockwise to increase tension for heavier TVs.
1 2
6 mm Hex Key
6 mm Hex Key
15-09-382-933501-EN.indd 7 10/7/2015 10:12:56 AM

8
7. Cable Management
8. Adjustment
3 mm
Hex Key
3 mm
Hex Key
5 mm
Hex Key
C
A
T
CHER
180°
180°
180°
360°
15°
15°
Max 13.8” (350 mm)
Height Adjustment
2.7 - 24.9”
(69 - 632 mm)
To adjust the desired location or tilt, use an appropriate 3 mm or 5 mm Hex Key to adjust. Turning counter-
clockwise reduces damping and clockwise increases damping.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
15-09-382 93-3501_RevA
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Connect the cables to the display, and press cable cover
inward to route the cables through the space.
Note: Leave slack in cable for cantilever arm movement.
15-09-382-933501-EN.indd 8 10/7/2015 10:12:58 AM