Triumph 45-6736W User manual

1-888-996-2729
FAX: [phone]
[e-mail]
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville IN 47706
When contacting Escalade Sports please provide your model number, date code (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.
Your Model Number:
Please have your model number when inquiring about parts.
Date Code:
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
45-6736W/F
2-45-6736F- -HL
1

2
Make sure you understand the following tips before you begin to assemble your hockey table.
1. Start all bolts by hand before tightening.
2. Some drawings or images in this manual may not look exactly like your product. Please
read and understand the text before starting each assembly step.
TWO ADULTS ARE REQUIRED TO ASSEMBLE
THIS 4-IN-1 AIRZONE SWIVEL TABLE
Assembly Tips
Tools Required:
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO ASSEMBLE THIS GAME TABLE
Allen Wrench (Included)
IMPORTANT! READ EACH STEP
IN THIS MANUAL BEFORE YOU
BEGIN THE ASSEMBLY.
Phillips Screwdriver
Furniture Polish and Cloth
SOCCER, BILLIARDS, AIR HOCKEY, TABLE TENNIS
PLUS BONUS AIRZONE SOCCER GAME

3
HARDWARE IDENTIFIER
(To Scale)
H1 = 8 pcs H2 = 8 pcs
4.5 mm x 10 mm
4 mm x 22 mm
Phillips Head Bolt Flat Washer
H5 = 24 pcs
6.5 mm x 16 mm
Flat Washer
T1 = 1 pc
H3 = 8 pcs
M4 Nylock Nut
H4 = 8 pcs
6 mm x 40 mm
Allen Head Bolt
H7 = 16 pcs
6 mm x 25 mm
Allen Head Bolt
Allen Wrench
(Not to Scale)
4 mm x 40 mm
Phillips Round
Head Screw
H6 = 26 pcs
3.5 mm x 35 mm
Phillips Flat
Head Screw
H9 = 12 pcs
3.5 mm x 25 mm
Phillips Flat
Head Screw
H10 = 4 pcs
3.5 mm x 28 mm
Phillips Round
Head Screw
H12 = 16 pcs
H11 = 2 pcs
Plastic Pivot Bolt
3.5 mm x 14 mm
Phillips Round
Head Screw
H8 = 12 pcs
(Not to Scale)

4
PARTS IDENTIFIER (Not to Scale)
P1 - Main Cabinet
(1 pc)
P3 -Right Leg
(2 pcs)
P4 - Left Leg
(2 pcs)
P2 - Leg Top
End Apron
(2 pcs)
P5 - Side Leg Panel
(2 pcs)
P6 - End Leg Panel
(2 pcs) (2 pcs)
P7 - Center Frame Support P8 - Top Side End Panel
(2 pcs)
P9 - Ball Storage
Board-Lower
(2 pcs)
P10 - Goal Box
(2 pcs)
P11 - Table Tennis
Board
(1 pc)
P16 - White 2-player
Rod Assembly
(1 pc) (1 pc)
P15 - White 5-player
Rod Assembly
P14 - White 3-player
Rod Assembly
(2 pcs)
(2 pcs)
(4 pcs)
P19 - Red 2-player
Rod Assembly
P12 - Leg Leveler
(1 pc) (1 pc)
P18 - Red 5-player
Rod Assembly
P17 - Red 3-player
Rod Assembly
(2 pcs)
(4 pcs)
P20 - Lock Latch
P13 - Manual Scorer
with rod handle, plastic washers,
rod end caps and bumpers attached
with rod handle, plastic washers,
rod end caps and bumpers attached
with rod handle, plastic washers,
rod end caps and bumpers attached
with rod handle, plastic washers,
rod end caps and bumpers attached
with rod handle, plastic washers,
rod end caps and bumpers attached
with rod handle, plastic washers,
rod end caps and bumpers attached

5
(2 pcs)
(2 pcs)
A12- Table Tennis Net
A2 - Table Tennis Paddle
(1 pc)
P23 - Side Pocket
Shield
(2 pcs) (2 pcs)(2 pcs)
A5 - Cue Stick
A6 - Billiards Playfield Brush
(1 pc)
A4- Table Tennis Net Post
A3 - Table Tennis Ball
(2 pcs)
A9 - Billiard Balls
A10 - Cue Holder
(1 pc)(1 pc) (1 set)
A8- Cue Tip ChalkA7 - Triangle
(1 pc)
A14 - A/C Adapter
(2 pcs)
A11 - Soccer Ball A13- Air Soccer Puck
(2 pcs)
(1 pc)
P24- Removable Bushing
Cap with Push Lock
(8 pcs)
with felt pad attached
(2 pcs)
A16 - Hockey Puck
A15 - Hockey Pusher
(1 pc)
P21 - Billiard Playfield
(4 pcs)
P22 - Corner Pocket
Shield

FIGURE 1
Step 1
Please inspect the main cabinet and playing surfaces before putting the game together.
Remove all the contents from inside the carton and verify that you have all listed parts as shown on the parts list.
NOTE: Parts are packed inside and under the table cabinet. Remove the billiards playfield P21 from Main Cabinet.
Inside the table cabinet you will find parts needed to assemble your table.
Attach the Plastic Pivot Bolts H11 to the Plastic Pivot Nuts C5 to each end of Main Cabinet.
Hand tighten the Plastic Pivot Bolts H11.
PARTS REQUIRED:
1 pc - P1 Main Cabinet 1 pc - P21 Billiard Playfield 2 pcs - H11 Plastic Pivot Bolt
P1
C5 Plastic
Pivot Nut
C5 Plastic
Pivot Nut
H11
(Factory Installed)
(Factory Installed)
P1
P21
P1
H11
Note: Double check to insure
all parts and packing materials
are removed from inside the
main cabinet.
Parts are also
packed underneath
the main cabinet.
Hand tighten tight
the H9 Pivot Bolt
at each end of cabinet.
gently push in on
Connect and
this connection
point to insure
good connection.

FIGURE 2
FIGURE 3
Step 2 Before Starting Step 2, Double Check That All Loose Table Components and Packing
Materials Are Removed From The Main Table Cabinet.
When all the parts are out of the Main Table Cabinet P1, replace the Billiards Playfield P21.
Attach the Billiards Playfield P21 by using screws H12.
Tighten, but do not strip out Screws H12
Step 3
Insert Corner Pockets Shields P22
and Side Pocket Shields P23 into
the the cabinet pockets using Screws H8.
Tighten, but do not strip out Screws H8
NOTE: Carefully pull and hold each
Pocket Shield tight into the pocket
for correct screw installation.
16 pcs - H12 3.5 x 28mm Phillips Round Head Screw
PARTS REQUIRED:
12 pcs - H8 3.5 x 14mm Phillips Round Head Screw 4 pcs - P22 Cornet Pocket Shield
2 pcs - P23 Side Pocket Shield
P23
H8
H8
P22
P1
P21
H12
H12
Note: While installing
the H12 screws,
press down on the Billiard
playfield to insure it is
seated correctly into the
P1 Main Cabinet.
Note: Double check that
Air Motor Cord is
plugged into Air Motor

8
FIGURE 4
FIGURE 5
H1
H2
P2
P2
H3
H1
H3
H2
P20
P20
H4
H5
P4
Step 4
Attach 2 pieces Lock / Latches P20 into the cut outs on Leg Top End Apron P2 with Bolts H1,Washers H2 and
Nuts H3, then tighten, but DO NOT over tighten..
PARTS REQUIRED:
2 pcs - P2 Leg Top End Apron
8 pcs - H1 4 x 22mm Phillips Head Bolt
8 pcs - H4 6 x 40mm Allen Head Bolt 8 pcs - H5 6.5 x 16mm Flat Washer 8 pcs - H3 M4 Nylock Nut
8 pcs - H2 4.5 x 10mm Flat Washer
2 pcs - P3 Right Leg 2 pcs - P4 Left Leg 4 pcs - P20 Lock / Latch
Note : Predrilled holes
Note : This cut out at top.
Note : This cut out at top
Step 5
Attach the Right leg P3 and Left Leg P4 to the
Leg Top End Apron P2 by inserting Bolts H4 with
washers H5 into the predrilled holes of the leg and
into the Barrel Nuts, then tighten,
but DO NOT over tighten.
NOTE: Study diagram closely for
correct assembly. Before assembly
check each Barrel Nut with a Bolt H4 to
insure correct alignment between Barrel
Nut and Bolt H4. Adjust Barrel Nut as
required using a screwdriver.
NOTE: Correct
location of
Corner Braces
Barrel Nut
inside
H4
H5
P3
Please install Lock/Latches P20 exactly
per the diagram for correct operation.
Heads of
Barrel Nuts
this backside
Heads of
Barrel Nuts
this backside
T1
T1

9
P2
P2
P4
FIGURE 6
FIGURE 7
H6
P9
H6
H6
H6
P12
P12
H6
P10
Corner Braces
This Side
Step 6
Step 7
Screw the Ball Storage Board-Lower P9 to the Leg
Top End Apron P2 using screws H6 into predrilled
holes.
Install leg levelers P12 to the bottom of each Leg P3 & P4.
Attach the Goal Box P10 to the Leg Top End
Apron P2 with screws H6 using the predrilled holes.
Tighten, but do not strip out screws H6.
Note: Be careful to orientate parts exactly
the same as the assembly diagrams.
Tighten, but do not strip out screws H6.
Note : Predrilled holes
Note : Predrilled holes
P3
PARTS REQUIRED:
2 pcs - P9 Ball Storage Board-Lower
18 pcs - H6 4 x 40mm Phillips Round Head Screw
4 pcs - P12 Leg Leveler2 pcs - P10 Goal Box
Important Note :
Please double check and
attach P10 to Leg Assembly
exactly as per diagram.
Note: Align all 4 holes
to install H6 Screws

10
FIGURE 8
FIGURE 9
P5
P6
P6
P5
H7
H7 H7
H7
H5
H5 H5
H5
P7
H6
H6
Step 8
With the help of another adult, attach the Side Leg Aprons P5
and End Leg Aprons P6 to the assembled leg pedestals by
aligning the holes in the corner braces on the leg pedestal with the
predrilled holes in the Leg Aprons P5 & P6 using bolts H7 and
washers H5.
Tighten all H7 Bolts using the Allen wrench T1 at this time.
Step 9
Attach the Center Frame Supports P7 to the Side Leg Apron P5
using predrilled holes with Screws H6
Tighten, but do not strip out screws H6.
Leg Pedestal
Note: The steel heads of the
pre-installed T-Nuts in the
P6 End Aprons must go to the
inside for correct assembly.
Corner Brace
Note : Predrilled holes
PARTS REQUIRED:
2 pcs - P5 Side Leg Panel 8 pcs - H6 4 x 40mm Phillips Round Head Screw2 pcs - P7 Center Frame Support
2 pcs - P6 End Leg Panel 16 pcs - H5 6.5 x 16mm Flat Washer 16 pcs - H7 6 x 25mm Allen Head Bolt
Heads of T-nut inside
Note: The Pilot Holes for