Tunersys WS162 User manual

WS162P CBA Produ ct Guid e V1.3 en
TUNERSYS
TUNERSYS WS162 WiFi Internet R dioBluetooth Amplifier Bo rd for Bookshelf Spe ker Guide
9. Configuration
Here you will find the complete settings / options available to configure your own tuner. On
the main menu, navigate to Configuration setting. Press OK and you will see a list of options
available.
Wi Fi Network
• Add / Remove AP
Add AP It will scan for a list of routers around.
Remove AP If you have already added a router and want to remove it, choose this option.
Note Always bring the Amplifier within 2 meters of the Wi Fi router for best results.
• AP: [ ]
If you have added more than one routers on the radio and want to switch to another one,
select this option to change.
• Signal
This is to show the strength of the Wi Fi Signal of the Wi Fi router as received by the
radio. Usually signal levels lower than 70dBm is at weaker level and if it affects the
reception of your radio, you may need to optimize the router location or check any
problem of the router itself.
• IP
The IP is set Dynamic by default. Select to change Fixed IP according to your network
condition.
• DNS
The DNS is set Dynamic by default. Select to change <Fixed> DNS according to your
network condition.
Wi Fi Channels
Not all of the Wi Fi channels are available in every country. There may be variation between
different countries. Therefore it is necessary to choose the Wi Fi channels to ensure the Wi
Fi
performs satisfactory.
We have already set the channels according to the requirement in different countries.
Choose the country you are staying from the list to get the correct channel. The
Europe/United Kingdom is set by default, press [OK] on the Remote control or push the
[Tune/Select] knob on mian unit to edit the country selection. Adjust backlight level when
power off and Under night or dark environment When Power off,You can off or Adjust the
Indicator LED Light and backlight level for the display as you prefer.press and hold the
[Power/Menu ] knob on main unit or press the [Power/Menu ] button on remote to turn off
the main unit ， then adjust the backlight level as you like by rotating the [Tune/Select] knob
on mian unit or [▲/▼] button on remote. There are 24 settings : Level 0 to 24, Can Keep
Date and time display and The Indicator LED light and backlight is off when Level set to 0
Page5
Page4
Tel: + 86 756 362 6622
https://www.tunersys.com
Eamil ： [email protected]
Instagram:@tunersysradio
Facebook: tunersysradio
Twitter: @tunersys_com
Adress:
ROOM 213,BUILDING D4,NO.1,SOFTWARE PARK
ROAD,TANGJIA BAY,HIGH TECH ZONE,ZHUHAI,CHINA
Indicator Lights Source State
Blue UPnP
Red Internet radio/My favourite
Purple Blue tooth
NC AUX
Sources Status Indicators
5. Bluetooth playback
Before transmission between your Bluetooth device and the radio is possible, both de
vices must be coupled. This process is called "pairing". The Tuner is served as a re
ceiver, to receive music stream to play on the Tuner.
If you have already paired a Bluetooth device before, this connection will be restored
automatically when both devices are in range and Bluetooth operation has been selected
on the radio. "Pairing" does not have to be repeated. This function may need to be acti
vated in your Bluetooth device, however.
• Push the Menu button to display the selection menu for the different playback modes.
• Use the up / down button to select the playback mode Bluetooth and push the dial
switch.
• Switch your Bluetooth device to which you want to connect the radio on and activate the
pairing mode here. The device scans for Bluetooth devices in the reception range.
• When the radio is found, your bluetooth device shows its name TUN01 L XXXX (the
XXXX is an identification code for your radio unit).
• Select the radio at your BT device.
• Start playback on your BT device.
• Playback now takes place using the radio.
6. Alarm Setting
• Choose Alarm from the main menu or press the [Alarm] button on the remote control.
• Select either Alarm 1 or Alarm 2, choose Turn on to activate the Alarm.
• Follow the alarm wizard instructions to set the alarm.
• The wizard will guide you through the settings below:
Time Set the time for the alarm
Sound You can choose Wake to My Favourite, Tone as the alarm source.
Wake to My Favourite Please preset your favorite station before setting this as
the alarm source. Repeat You can schedule the alarm as you desire —Everyday, Once
or multiple days.
Alarm Volume Adjust the volume of the alarm as you like by rotating the [Tune/Select]
knob on main unit or [▲/▼] button on remote.
• After the above settings are completed, press the [◄] button to exit and make sure the
Alarm is turned on. You will see the Alarm icon appeared on the display if it is activated.
7. Sleep Timer Setting
You can set the timer to let the radio goes standby after the selected time elapsed in the
range of 15 minutes to 180 minutes.
Press [Sleep] button on the remote control to set the timer.
You will see the icon appeared on the display if the timer is set.
8.Home page menu
•My Favourite/Internet Radio/Media Centre/Blue tooth/AUX in/Alarm/Sleep/Timer/
Configuration
8.0,Configuration and Main function Introduce
8.1,Alarm:2 Alarm: Alarm1 Alarm 2;
Into Alarm 1 or Alarm 2 And Set Alarm off or on Set a Alarm time when Alarm on
Sound(Alarm): Set a Alarm tone or a Station or song From My Favourite or UPnP/DLNA
Media Centre;
Repeat(Alarm): Every/Day/oncs/Monday/Tuesday/Wednesday/Thursday/Friday/
Staurday/Sunday;Alarm Volume: Can Set a suitable level;
Sleep Timer:Turn Off,15,30,45,60,90,120,150,180Minutes
Configuration: Network,Date & time,Language,Location Radio,
Playback setup:Repeat all/ Repeat one/Shuffle<br>
My name setup:Rename;
Resume when power on:When "power on" reboot to automatically restore the song or
station that was played during the previous shutdown.When "power off", restart and play
normally;
Contrast for LCD Display: 30~63%;Buffer Time: 2 Seconds/5 Seconds;
Aux in Grain :0dB / 6dB;Information:Network/Syetem Information;
Software Update;Reset to Default;
Dimmer: Mode set Dim/Normal;Level set:Bright 0~100%, Dimmer 0~100%; Language
Choose:Deutsch/English/Espanol/Francais/Italiano/Nederlands/Polski/Pyccknn/Chinese;
Configuration: Network.
Spe ker Right -
Spe ker Right +
Antenn for WiFi & Bluetooth
Spe ker Left -
Spe ker Left +

2.0, Network setup
Internet connection can be setup via wireless LAN (WiFi).your amplifier requires a broadband
Internet connection through WiFi. The easiest way to connect is through a Wifi router.
Wireless LAN (Wi Fi)
• If this is first time use, the Configure Network wizard will be displayed. Use knob on amplifier
or left and right right arrows on remote to Choose Yes to start configuring network. Press the
[Back/◄] button to highlight Yes and press [OK] on remote to confirm.
• Select Add/Remove AP from the list, use the [OK] knob on amplifier or down and up arrows
on remote to scroll and press knob to confirm, then highlight Add AP (Scan) press [OK] to
confirm.
• It will start scanning the available Wi Fi routers around. Scroll to your network and press
[OK] on remote to confirm.
• If your wifi network has a security code protected, it will ask you to enter the passphrase/
password.
How to input security code for your wireless network using remote control
On the alpha numerical keypad, press each button repeatedly to cycle through the letters,numbers and sym
bols as listed below.To input a character, scroll to the correct one and when it is highlighted, press the ► button
to input the next character. When it comes to the last character of the password and it is highlighted, press
[OK] to confirm.
Button 1: 1 and different kind of symbols ! @ # $ % ^ & * ( ) _ + [ ] { } ; : ' ” \ | , . / < > ? Button 2: 2 A B C a b c
Button 3: 3 D E F d e f Button 4: 4 G H I g h I Button 5: 5 J K L j k l Button 6: 6 M N O m n o
Button 7: 7 P Q R S p q r s Button 8: 8 T U V t u v Button 9: 9 W X Y Z w x y z Button 0: 0
Wi Fi signal bar
1.1,Controls nd Buttons ,WS162 Re r
1.2, Remote Control
Function/
Botton
Name
WS
162
Re
mote
Home page
Power
On/Off
Ok/Enter
Up
Down
Left/back/
Delect
Right/Next
Play/Pause
1.3,M in Botton T ble
Straightline Control
Remote
Control
Reflect control
Remote
Control
1.51 ， Connect the Wire From Master
speaker to Slave speaker ， Insert the
Speaker wire when pushing Terminal on
Master speaker;on Slave speaker
,Turn Terminal nut counterclockwise,then
Insert the Speaker wire on Slave
speaker,
1.52 ， Connect the power supply,
DC power (mains) input(+24V/3.5A),With
a Power Adapter connect to AC power
input(~100 240 V, 50 60 Hz),Use only the
supplied power cord to connect to a
power outlet (using a third party power
cord will void your warranty).
Wall
1.4,Remote Control
Direction
1.5, Connect the Wire
Page1 Page2 Page3
Configure Network ?
<Yes> No
Wi-Fi Channel
Add/Remove AP
AP:[ ]
Add A P( WPS button)
Add A P( Smart Confiig)
Add AP
（
Scan
）
08:30 m
My F vourite
Medi Centre
Internet R dio
How to input security code for your wireless net
work Using control button on the Amplifier
Use the knob on the amplifier to scroll through the
characters, when the correct one is highlighted, press
[Forward/►] button on either the remote or the console
to input the next character. When it comes to the last
character of the password and it is highlighted, press
[Select] on main unit to confirm. Note: The password is
case sensitive. When the Wi Fi connection is success
ful, the Association Complete will be shown briefly. The
wifi signal bar will appear on the top left corner of the
display:
3. Internet Radio
On the main menu, choose Internet Radio and you will
find the options as diagram on the left
Skytune
Select Skytune to start enjoying thousands of radio
stations over the world. You can filter your
search by Region, Music genre and talks.
The Local Radio let you access quickly the stations
available in your local area through internet connection.
Search
History
Skytuner
Local Radio
Globle All
Globe By Genre
Globe By Region
Globle Most Popular
Note - You c n ch nge the Loc l R dio re under
Configur tion> Loc l r dio setup. Ple se refer to
section 11 for the det ils. Note - When you scroll
long the list of Globe All nd w nt to quickly re ch
to cert in point of the long list, input the index
number on the remote control to quickly jump to
th t point. For ex mple, on the remote control,
input 2 8 nd press OK, it will highlight the st tion
no. 28.
Search Inste d of browsing the r dio st tion list, you c n input few ch r cters of the desired
st tion to filter out / short list the st tions.
History The r dio memorizes the st tions you h ve listened up to 99 st tions. If
you h ve listened more th n 99 st tions, it will supersede the first st tion th t you
h ve listened.
Start playing internet radio When r dio st tion st rts pl ying, more dio
inform tion c n be displ yed. such s the stre ming bit r te, n me of the song,
rtist n me (if v il ble) nd the r dio's st tion n me (if v il ble):
My Favorite
This is to show the list of your favorite stations which have been assigned to the pre
sets.
Preset a station
You need a remote control to preset the station.
When a radio station is playing, press the button f vorite on the remote control to
add the radio station to your favorite list, you will see the icon appear on dis
play . It means the station is added to the Favorite list.You can store up to 99
presets My Favourite and History.
Recall a radio station
Press the button on the remote control to recall the list of presets, or navigate to My
Favourite on the main menu and select it to confirm.
Edit your favorite list
On the Favorite list, choose the radio station you want to edit then press the [►] button
on the remote control (or press [Forward/►] on main unit ). It will enter the Edit menu
with the following options:Move down To move down the ranking of a station,Move up
To move up the ranking of a station,Delete To delete a particular station 。
4. Media Centre
The device supports UPnP and is DLNA compatible.
This provides the opportunity to stream music from your network. However, this requires
you to have a compatible device in your network that can function as a server. This can
be e.g., a network hard drive or a conventional PC with e.g., Windows 8 via which
access to the shared folder or media sharing is permitted. The folders can then be
browsed and played on the Tuner.
Note Please make sure your computer laptop is on the same Wi Fi network as the
Radio before you start using this function.
Music streaming
• Once the UPnP/DLNA compatible server is configure to share media files with your
radio, you can start music streaming.• On the main menu, select Media Centre and
choose UPnP.• It may take a few seconds for the radio to complete the scan for avail
able UPnP servers. If no UPnP servers are found, it will show Empty List.
• After a successful scan is done, select your UPnP server. • The radio will show the
media categories available from the UPnP server, e.g. 'Music','Playlists' etc.
• Choose the media files that you wish to play.
You can set the mode of playback under Configuration > Playback setup.
My Playlist
You can make your own playlist for the UPnP music files. Choose and highlight the
song you want to add to playlist, press and hold the [Tune/Select] knob on main unit or
press and hold the [OK] button on remote, until the sign appears. The song will be
added to My playlist.
TUNERSYS WS162 WiFi Internet R dioBluetooth Amplifier Bo rd for Bookshelf Spe ker