Tuscany Ql056 User manual

QL056

# 6725162

OWNER’S MANUAL

LAUNDRY CABINET KIT

2-DOOR

# 6725162

Table of Contents

Safety Information ..................................2

Warranty

One Year Limited Warranty...........................3

Warranty Claim Procedure ...........................3

Pre-Installation

Tools/Materials Required ............................4

Parts Required ....................................4

Package Contents .................................5

Installation

Installing the Cabinet Feet ...........................6

Installing the Handles ..............................6

Installing the Faucet ...............................7

Installing the Strainer ..............................8

Mounting the Utility Sink ............................9

Placement .......................................9

Drainage ........................................9

Supply Line ......................................9

Maintenance

Cartridge Replacement .............................9

Care and Cleaning

Utility Sink ......................................10

Cabinet.........................................10

Service Parts......................................11

Safety Information

READ AND SAVE THESE INSTRUCTIONS

1. Unpack and inspect this product for chips, scratches, cracks,

dents, and scuff marks. Do not install this product if any

damages or defects are identied.

2. Use this product only in the manner intended by the

manufacturer. If you have any questions, contact the

manufacturer.

3. Installation work and plumbing must be done by qualied

person(s) in accordance with all applicable codes and standards.

4. Protect the entire surface during installation.

DANGER: Always wear safety goggles and gloves in order

to avoid personal injury.

Please contact cs@conglomkb.com or 1-888-449-9194 for further assistance.

Warranty

ONE YEAR LIMITED WARRANTY

A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or

damage that could have been discovered or avoided by proper inspection and testing prior to installation.

We warrant this product to be free from defects in materials or workmanship for one (1) year from the date of purchase. Proof of purchase

(original sales receipt) from the original consumer purchaser must be made available to us for all warranty claims.

This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following

the manufacturer’s instructions. It does not apply in the event of product damage due to the use of other than genuine our replacement

parts, (Replacement parts may be obtained by e-mail at cs@conglomkb.com or by calling 1-888-449-9194 between 8:30 am - 5:00 pm

EST) installation error, abuse, misuse or improper care and maintenance (whether performed by a plumber, contractor, service provider

or member of the purchaser’s household). The warranty excludes damage due to aggressive air or water conditions, harsh or abrasive

cleaners and/or materials.

Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this

product. We will not be held liable for inconvenience caused by loss of use of this product, costs incurred for labour or materials, removal

and installation of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or

replacement are the responsibility of the user.

Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be

defective under normal use and service during the warranty period.

Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-

warrantable items include, but are not limited to:

- Improper installation not in accordance with manufacturer’s instructions.

- Dents and/or scratches incurred during shipping, handling, or installation.

- Change in colour or nish due to chemical usage.

- Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of abrasive cleaners.

- Alterations made to the unit by the purchaser or installer.

- Damage caused by accidental impact, re, ood, freezing, and normal wear.

- Bends and warping caused by forced connections, over-tightened ttings, and inadequate support during installation.

- This warranty does not extend to commercial and institutional installation or use.

WARRANTY CLAIM PROCEDURE

If a claimable defect occurs or replacement parts are needed,please contact our customer service team at cs@conglomkb.com or 1-888-449-9194

(8:30 am - 5 pm, EST, Monday - Friday).

Before you make your call, please ensure that you have:

- Model number or description.

- Proof of sale.

- Details regarding the defect and/or part number.

- Name(s) and address(es) of the owner and/or installer.

# 6725162

Pre-Installation

TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)

Adjustable

wrench

Needle nose

pliers

Phillips

screwdriver

Utility knife Pipe wrench Sealant

Hacksaw Carpenter’s level Hex wrench

Safety gloves Safety goggles

PARTS REQUIRED (NOT SUPPLIED)

Tail Pipe P-Trap Supply Lines

Please contact cs@conglomkb.com or 1-888-449-9194 for further assistance.

Pre-Installation (continued)

PACKAGE CONTENTS

Carefully check the utility cabinet for damage and/or missing parts prior to installation. If there is any damage or if you are missing parts,

do not proceed with the installation. Report damage and/or missing parts immediately to our customer service team at cs@conglomkb.com

or 1-888-449-9194 (Service available in English and French, Monday - Friday from 8:30 am - 5:00 pm EST). Please do not dispose of

packaging before you are satised with your new utility cabinet.

A B C

E BBF AAG

Part Description Quantity

A Cabinet 1

B Faucet 1

C Cabinet legs 4

D Utility sink 1

E Strainer assembly 1

F Strainer basket 1

G Door handle 2

AA Handle screws 4

BB Cabinet Leg Screws 16

# 6725162

Installation

CABINET FEET INSTALLATION CAUTION: Do not rest or bump the leveling feet on the side

as this may cause them to detach or break.

- Remove the cabinet (A) and place it on a soft,

protective surface.

- Attach each cabinet leg (C) to the bottom of the cabinet (A)

using four of the provided screws (BB).

- Gently rotate the cabinet (A) right side up.

- Place a carpenter's level on top of the cabinet, then adjust each

leveling foot until the cabinet is level.

DOOR HANDLE INSTALLATION

- Insert the door hand screws (AA) into the pre-drilled holes on

each door.

- Attach the door handle (G) and hand tighten the door handle

screws (AA). Do not overtighten.

Please contact cs@conglomkb.com or 1-888-449-9194 for further assistance.

Installation (continued)

DOOR POSITION ADJUSTMENT

If the doors need to be repositioned, the hinges can be adjusted to

ensure a precise t with the cabinet.

1. The lateral adjustment screw adjusts the door orientation

from left to right.

2. The horizontal adjustment screw adjusts the door

orientation from front to back.

3. The vertical adjustment screw adjusts the orientation

up or down.

INSTALLING THE FAUCET

Spray

Head

Spray Head

Connector

Faucet body

Hose

Faucet outlet

Sink

Gasket

Retaining nut Metal Washer

Screws

Faucet outlet

Counterweight

Hose

- Connect the spray head to the hose.

- Remove the gasket, metal washer, and retaining nut from the

faucet.

- Install the faucet through the hole in the sink.

- From underneath, secure the faucet to the sink with the gasket,

metal washer, and retaining nut.

- Tighten the retaining nut by hand until it is snug. Use a wrench to

tighten it down. Gently tighten the two screws on the retaining nut.

Do not over tighten.

- Hand-tighten the hose to the faucet outlet. Tighten the ttings

using two wrenches. Hold the faucet outlet steady with a wrench

while turning the hose tting with another wrench until it is snug.

NOTE:

Failing to use two wrenches can damage the faucet. Do not

overtighten.

- Push the spray head into the faucet neck. Install the counterweight

a couple of inches from the bottom of the hose on the side closest

to the spray head. There should be no slack in the hose and it

should retract freely.

- Connect the water supply lines (not supplied) to the faucet.

# 6725162

Installation (continued)

INSTALLING THE STRAINER

- Apply plumbing putty or silicone sealant to the top side of the

drain opening.

- Insert the strainer body into the drain opening and press it down

until it is evenly seated.

- Assemble the rubber gasket, friction washer and strainer locknut

onto the strainer body from underneath the sink. Hand tighten

the strainer locknut until it is snug.

Do not overtighten.

- Insert the plastic ange into the ange-end of the tailpipe (not

supplied) then secure the tailpipe to the strainer body using the

connecting nut. Tighten the connecting nut until it is snug. Do

not overtighten.

- Remove excess sealant from around the drain opening.

NOTE:

The tail pipe is not supplied.

Strainer Body

Sealant

Sink

Rubber Gasket

Fiber Washer

Strainer Locknut

Plastic Flange

Tailpipe

Connecting Nut

Strainer Basket

Please contact cs@conglomkb.com or 1-888-449-9194 for further assistance.

Installation (continued)

MOUNTING THE UTILITY SINK

SEALANT

- Carefully place a bead of sealant all around the top of the

cabinet (A).

- Ease the sink (D) into the cabinet (A). Ensure that it is placed

evenly and is centered on the cabinet. Wipe off any excess

sealant. Use masking tape to hold the sink in place until the

sealant dries.

PLACEMENT

Position the cabinet in the intended location. If required, level the cabinet by adjusting the four leveling legs and checking the alignment of the

top using a carpenter’s level. Secure the cabinet to the wall if necessary.

DRAINAGE

The tailpipe (not supplied) previously installed to the drain can now be connected to your household plumbing. In some cases, your household

plumbing will have to be modied to ensure proper drainage. If so, please consult a licensed plumber to complete needed modications.

SUPPLY LINES (NOT INCLUDED)

Connect the supply lines to your home’s water supply as per manufacturer’s instructions.

Open the hot and cold water supply valves and check to make sure they have

been installed to appropriate inlet ports. Check for leaks. Run hot and cold water

uninterrupted for about one minute to remove any residue from the lines.

Maintenance

CARTRIDGE REPLACEMENT

Handle Lever

Decorative Cap

Retaining Nut

Cartridge

Handle Body

Faucet Body

Setscrew

O-Ring

- Turn off the water supply to the faucet.

- Unscrew the handle lever. Loosen the setscrew with the hex key

provided and remove the handle body.

- Gently unscrew the decorative cap and retaining nut.

- Pull the cartridge out of the faucet body and replace it with a

new ceramic cartridge. Ensure new cartridge is seated properly

with the locating pins in appropriate place.

- Secure the cartridge in place using the retaining nut.

- Gently tighten the retaining nut using a wrench.

Do not overtighten.

- Reinstall the decorative cap. Slide the handle body back onto the

cartridge and make sure it rotates freely. Secure the handle body in

place using the setscrew and reinstall the handle lever.

- Turn the water supply to the faucet back on.

- Operate the faucet to make sure everything works correctly and

check for leaks.

# 6725162

Care and Cleaning

Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care.

SINK CABINET

Do Do

- After use, always rinse your sink with tap water to dilute and

remove deposits.

- Towel dry after use whenever possible to prevent water spots.

Should water spots occur, clean with a mild solution of vinegar

and water followed by a thorough rinse.

- Use liquid soap, a general household cleaner, or a weak

solution of vinegar and water for regular cleaning.

- Only use plastic scouring pads recommended for use in

stainless steel sinks, and only use them in the bowl of the

sink. Scrub in the direction of the satin nish lines.

- Remove dust and dry dirt with a soft, damp cloth.

- Clean grease, oil, paint and ink stains with isopropyl (rubbing

alcohol). Immediately rinse with water after

stain removal.

Do not Do not

- Do not allow any food, detergent, soap or grease to dry or sit for

extended periods of time on the surface of the sink.

- Never use abrasive cleaning products, as they will dull and

scratch the nish.

- Do not use scouring pads on the deck, as they will dull the nish.

- Never use steel wool pads, as they will leave iron particles on the

sink, which will cause corrosion.

- Never leave steel or cast iron pans in your sink for extended

periods of time, as this can cause corrosion.

- Never use chlorine-based cleaners in your new sink, they could

lead to rust spots and discolouration. If you must use them, rinse

sink thoroughly with fresh water immediately after use. If any

chemicals or glue make contact with the sink during installation,

wipe clean and rinse thoroughly with fresh water.

- Do not allow your cabinet surface to come into contact with

products such as acetone (nail polish remover), nail polish, dry

cleaning solution, lacquer thinners, gasoline, pine oil, etc.

- Use caution when using sharp instruments that may fall and

scratch the surface.

SCRATCH, SPOT, AND BLEMISH REMOVAL AND SURFACE RESTORATION:

Little rust spots and blemishes that periodically appear in the sink are typically the result of the steel interacting with the chemicals found in the

vast spectrum of substances that sinks are commonly exposed to. They may also get transferred from other objects placed or left in the sink.

Scratches are the result of regular wear and tear.

To remove scratches, spots, and blemishes from the sink, rub them with a non-metallic scouring pad (e.g. Scotch-Brite®) combined with a mild

abrasive cleaner (e.g. Vim® or Barkeeper’s Friend®). Always rub the surfaces in the direction of the grain of the steel. When nished, rinse the sink

with water and dry it with a towel to allow the sink to form a protective outer layer. This procedure can also be used to renew all of the surfaces of

the sink.