U.S. General 58956 Assembly instructions
Visit our website at: http://www.harborfreight.com
58956
IN-DRAWER
POWER TOOL HOLDER
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual (or month and year of purchase if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference. 23d
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2022 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 58956
Specifications
Dimensions 11.87" W x 11.87" H x 19.25" D
Compatibility US General Series 3 Cabinets
56" and 72"
Included Hardware 13x self tapping screws
IMPORTANT SAFETY INFORMATION
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.
Use Precautions
TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:
1. DO NOT SIT, STAND OR CLIMB ON THIS ITEM.
2. This product is not a toy. Do not allow
children to play with or near this item.
3. Use as intended only.
4. Inspect before every use; do not use
if parts are loose or damaged.
5. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Attach Left Panel (2) to Back Panel (1)
using two Self Tapping Screws (8).
Back Panel (1)
Left Panel
(2)
Self Tapping Screw (8)
2. Attach Right Panel (3) to Back and Left Panel
Assembly using two Self Tapping Screws (8).
Back and Left
Panel Assembly
Right
Panel (3)
Self Tapping Screw (8)
Page 3For technical questions, please call 1-888-866-5797.Item 58956
3. Connect Bar (4), pre-assembled with
10x Brackets, to Left and Right Panels
using four Self Taping Screws (8).
Bar
(4)
Self Tapping Screw (8)
4. Determine the height of each Cup, then attach the
3x Large Cups (5) and 2x Small Cups (6) to the
Back Panel with five Self Tapping Screws (8),
one per Cup.
a. Place largest power tool (sold separately)
in a large cup. Hold tool in cup and place
its handle horizontally on the bar. Handle
should rest level on the bar and tool
should be fully inside the holster.
Note: If tool not fully inside the holster, lower the bar.
b. Secure cup to Back Panel using
the supplied screw.
c. Repeat for all remaining cups. Fit the
tool (sold separately) in the cup, rest tool
handle on the bar then secure the cup to
the Back Panel using a supplied screw.
d. Arrange cups so that three large cups
are on one side and two small cups are
on the other side, as shown below.
Note: Cups will likely be at different heights.
Large Cup (5)
Self Tapping Screw (8)
Small Cup (6)
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. The Holder is compatible with US General
Series 3 Cabinets 56" and 72".
2. Pull out a bottom drawer and place empty,
assembled Tool Holster inside.
3. Load tools (sold separately), making sure they
fit fully inside the holster and are secure. Be
sure drawer fully closes with all tools loaded.
Parts List and Diagram
Part Description Qty
1 Back Panel 1
2 Left Panel 1
3 Right Panel 1
4 Bar 1
5 Large Cup 3
6 Small Cup 2
7 Bracket 10
8Self Tapping Screw 13*
Notes:
*only one Screw shown.
1
2
3
4
5
6
7
8
26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175451897 when ordering parts.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
