Ubiquiti UniFi UVC-Micro User manual

Model: UVC-Micro
Quick Start Guide
®

Before You Begin
The UVC Micro is designed to work
with the UniFi® Video (v3.1.1 or higher)
controller software. The software may
be hosted on either:
• The Ubiquiti Networks®
UniFiNVR appliance (UVC‑NVR)
• A Linux/Windows computer
Note: The latest UniFi Video
software is available for free
download at:
downloads.ubnt.com/unifivideo

Package Contents
UVC-Micro
Camera
UVC-Micro
Base
Power
Adapter
Flat Base
Plate
Corner Base
Plate
Mounting
Tape
Screws
(Qty. 5)
Screw
Anchors
(Qty. 5)
Cable Clips
(Qty. 6)

Hardware Overview
LED Reset
LED The LED will light steady blue
during bootup. When the camera is
ready to connect to the Wi-Fi network,
the LED pattern will flash two times
accompanied by two beep tones. Once
connected to the network, the LED will
glow a breathing pattern.
Reset To reset network settings to
factory defaults, press and hold the
Reset button until the camera beeps two
fast tones.

Installation
Extend the Power Cable
The Power Adapter has an extendable
power cable that is concealed inside the
adapter casing.
1. Hold the outer casing of the Power
Adapter with the Ubiquiti U logo
facing towards you, and push in the
center of the logo until the adapter
releases from the outer casing.

2. Unwind the power cable to extend it
to the desired length. Then lock the
cable into the notch located under
the bottom of the U logo.
3. Slide the outer casing back onto the
adapter until it snaps into place.

Mounting Options
The camera may be used free-standing
or mounted in several ways:
• Magnetic Mounting
• Mounting with Tape
• Wall Mounting with Screws
• Corner Mounting with Screws
Magnetic Mounting
1. Attach the UVC‑Micro Camera and the
power cable to the UVC‑Micro Base.

2. Attach the camera assembly to a
metal (steel) surface.
*640-00157-02*
640-00157-02

Mounting with Tape
1. Remove the paper from one side of
the Mounting Tape, and center the
tape on the back of the Flat Base Plate.
2. Remove the paper from the other
side of the Mounting Tape and attach
the Flat Base Plate to the surface.

Wall Mounting with Screws
1. Place the Flat Base Plate at the desired
location and mark the two mounting
holes.
Note: If you are running the power
cable inside the ceiling or wall,
then mark the cable feed opening
below the mounting holes.

2. Use a 3 mm drill bit to drill a hole at
each mark, and insert a Screw Anchor
into each hole.
3. (Optional) When running the power
cable inside the wall or ceiling, cut the
hole for the power cable. Then feed
the cable through the hole and the
Flat Base Plate.

4. Attach the Flat Base Plate to the
surface by fastening a Screw to each
Screw Anchor.

Corner Mounting with Screws
1. Place the Corner Base Plate at the
desired location and mark the two
mounting holes.
2. Use a 3 mm drill bit to drill a hole at
each mark, and insert a Screw Anchor
into each hole.

3. Feed the power cable through the
back of the Corner Base Plate.
4. Secure the Corner Base Plate by
fastening a Screw to each Screw
Anchor.

Attaching the Camera
1. Attach the power cable to the back of
the UVC‑Micro Base.
2. Connect the UVC‑Micro Base to the
Base Plate by inserting the mounting
tabs into the slots on the base.

3. Rotate the UVC‑Micro Base to lock it.
4. Attach the UVC‑Micro Camera to the
UVC‑Micro Base, and pivot the camera
to the desired angle.

5. Plug the Power Adapter into a power
outlet. To secure the connection, use
the outlet cover plate screw to fasten
the Power Adapter to the outlet.
(Recommended)
Note: (6) Cable Clips with adhesive
tape are included to help hold
the power cable in place. Remove
the paper backing on each clip to
expose the adhesive tape.

Set Up the UVC Micro
Ensure you are running the latest version
of UniFi Video, v3.1.1 or higher (UniFi NVR
or computer‑based system).
Download the UniFi Video User Guide for
detailed information on how to set up
and use UniFi Video:
documentation.ubnt.com/unifivideo
UniFi Video Mobile App
For quick setup, a mobile app is available.
Install the UniFi Video app, and follow the
on-screen instructions:
• iOS: iTunes App Store
• Android: Google Play Store

Specifications
UVC-Micro
Dimensions 40.7 x 40.7 x 40.8 mm
(1.61 x1.61 x 1.61")
Weight 53 g (1.87 oz)
Network Interface 2.4/5 GHz Dual-Band Wi-Fi
Sensor Progressive Scan
RGB CMOS 1/4"
Lens EFL=2.38 mm / F2.4
View Angle 79.13° (H), 54.15° (V), 88.45° (D)
Night Mode Infrared LEDs with
Mechanical IR Cut Filter
Video Compression H.264
Resolution 720p HD (1280 x 720)
Max. Frame Rate 30 FPS
Microphone Yes
Speaker* Yes
Power Supply 5.5V (5,5V) Adapter with
Extendable Power Cable
Max. Power
Consumption 3.2W
Mounting Wall/Ceiling/Corner Kit
Operating Temperature 0 to 35° C (32 to 95° F)
Operating Humidity 20 to 90% Noncondensing
* Functionality coming soon with a software update

Safety Notices
1. Read, follow, and keep instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by
the manufacturer.
WARNING: Do not use this
product in a location that can be
submerged by water.
WARNING: Avoid using this
product during an electrical
storm. There may be a remote risk
of electric shock from lightning.