Ubisense Dimension4 UWB+BLE Tag User manual

Copyright © 2021 Ubisense Limited, All Rights Reserved
Wideband Location System
UB-Tag
Dimension4 UWB+BLE Tag
(D4UWBBLE)
User’s Manual
Written By
Andy Ward
Ubisense Limited
St Andrew’s House
St Andrew’s Road
Chesterton
Cambridge
CB4 1DL
ENGLAND
Tel: [phone]
Fax: [phone]
Email: [e-mail]
WWW: http://www.ubisense.net/
Released: September 2021

Copyright © 2021 Ubisense Limited, All Rights Reserved
Table of Contents
Introduction ...................................................................................................................................... 1
Regulatory Information for the United States of America ................................................................ 1
Regulatory Information for Europe .................................................................................................. 2
Regulatory Information for Canada ................................................................................................. 2
Device Specifications ...................................................................................................................... 3
User Information .............................................................................................................................. 4

1
Ubisense –Wideband Location System –UB-Tag Dimension4 UWB+BLE tag
Introduction
The UB-Tag Dimension4 UWB+BLE tag (model number D4UWBBLE) is a location tracking tag
for the real-time location of objects. It transmits wideband pulses which are picked up by a
network of basestations (Ubisensors), allowing the 3D position of the tag to be found. The use of
wideband technology enables greater positioning accuracy within buildings than other wireless
technologies, because it is much less susceptible to multipath interference effects. Applications of
the system include healthcare, workplace productivity, security, retail management and
manufacturing.
This document describes the features and specifications of the UB-Tag Dimension4 UWB+BLE
tag and important regulatory information concerning its use.
Regulatory Information for the United States of America
The UB-Tag Dimension4 UWB+BLE tag is approved under Parts 15.247 and 15.250 of the FCC
rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modifications to the equipment not expressly approved by the party responsible for
the grant of equipment authorization issued by the FCC could void the user’s authority to operate
the equipment under the grant of equipment authorization, for example:
CAUTION: Any changes or modifications made to the UB-Tag Dimension4 UWB+BLE tag
which are not expressly approved by Ubisense Limited could void the user's authority to
operate the equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This device complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. The device has been
evaluated as safe to use at any separation from the person.

2
Ubisense –Wideband Location System –UB-Tag Dimension4 UWB+BLE tag
Regulatory Information for Europe
Hereby, Ubisense Limited declares that the radio equipment type UB-Tag Dimension4 UWB+BLE
tag (D4UWBBLE) is in compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address: www.ubisense.net or from:
Ubisense
St. Andrew's House
St. Andrews Road
Chesterton
Cambridge
CB4 1DL
United Kingdom
This UWB transmitter must not be installed at a fixed outdoor location or used in flying models,
aircraft and other forms of aviation.
The device uses the following frequency bands, at the output powers shown:
Radio interface
Lower frequency
(MHz)
Upper frequency
(MHz)
Output power (dBm)
2.4GHz
2401.00
2481.75
2.1
Wideband
6099.742
7025.941
-44.0 (/MHz)
Regulatory Information for Canada
The Modular Tag V3.1 is approved under Industry Canada documents RSS-GEN, RSS-102,
RSS-247 and RSS-220.
Le Modular Tag V3.1 est certifié et approuvé conforme selon les documents de l’Industrie du
Canada RSS-GEN, RSS-102, RSS-247 et RSS-220.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This device complies with the safety requirements for RF exposure in accordance with RSS-102
Issue 5 for portable use conditions in uncontrolled environments.
Cet appareil est conforme aux exigences de sécurité relatives à l’exposition aux radiofréquences,
conformément à la norme RSS-102, édition 5, pour systèmes portables conditions d’utilisation
dans des environnements non contrôlés.

3
Ubisense –Wideband Location System –UB-Tag Dimension4 UWB+BLE tag
Device Specifications
Wideband transmitter section
Operates under: FCC Part 15.250
Industry Canada RSS-220
ETSI EN 302065-2
Centre frequency: 6.500GHz
-10dB bandwidth: 0.926GHz
2.4GHz proprietary BLE (Bluetooth Low Energy)-based radio transceiver
Operates under: FCC Part 15.247
Industry Canada RSS-247
ETSI EN 300328
Lowest channel frequency: 2401.00MHz
Highest channel frequency: 2481.75MHz
General specifications
Dimensions (WxHxD): 46mm x 41mm x 18mm
Weight: 24g
Power supply: Non-replaceable CR2477 lithium coin cell
Operating temperature range: -20ºC to +70ºC

4
Ubisense –Wideband Location System –UB-Tag Dimension4 UWB+BLE tag
User Information
The UB-Tag Dimension4 UWB+BLE tag device is shown below:
Switching on the tag
The device is shipped in a quiescent (non-transmitting) deep sleep state. To turn on the tag, bring
a magnet next to the side of the tag near the LED light pipe, as shown in the diagram above. The
LED on the tag will illuminate. Hold the magnet there until the LED turns off of its own accord –
the tag LED will then brighten from dim to bright, and will then go out.
At this point, the tag is running and transmitting location packets. Typically the tag will flash
periodically to show that it is awake (although the precise LED behaviour and tag update rate will
depend on the settings pre-programmed into the tag for your site).
Troubleshooting
In case of problems with your Ubisense location system and tags, please contact
[e-mail].
Disposal of device
The UB-Tag Dimension4 UWB+BLE tag has an exceptionally-long battery lifetime. Note that the
battery is not user-replaceable. At the end of the device’s lifetime, please either return to
Ubisense for recycling or dispose of in an environmentally-conscious manner.
LED indicator
Mounting holes
Strapping slot
Location of
magnetic sensor
(hold magnet on
side of tag here to
wake up device)