UNEEKOR QED User manual

USER MANUAL
Important: Read before using.

QED USER MANUAL 1
Notice
Grounding Instructions
In the event of a malfunction or breakdown, grounding provides a
path of least resistance for electrical current to reduce the risk of
electric shock. This tool is equipped with an electrical cord having
an equipment grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not t the outlet, have
proper outlet installed by a qualied electrician.

To Ensure Safe Use
Installation Environment
What’s Included
Hardware Installation
Step 1: Mounting Bracket
Step 2: Sensor Insert
Step 3: Connection
Step 4: Connection Status
Software Installation
Calibration Guide
Calibrating Instructions
Club Sticker Placement
Club Sticker Application
Appendix
Club Data
Ball Data
Speccations
Links
3
5
6
7
8
9
10
11
12
16
19
23
24
30
30
33
37
38
QED USER MANUAL 2
TABLE OF CONTENTS

QED USER MANUAL 3
To Ensure Safe Use
Improper handling or operation of this machine may result in injury
or damage to property. Points which must be observed to prevent
injury or damage are described as follows.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly. Material damage refers
to damage to home, furnishing, or
anything within the unit’s vicinity.
This symbol alerts the user to items
that should never be carried out.
Used for instructions intended to alert the
user to the risk of severe injury should the
unit be used improperly.
Safety
WARNING
Caution
NEVER

QED USER MANUAL 4
To Ensure Safe Use
Never attempt to disassemble, repair, or
modify shock, or injury. Entrust repairs to
a trained technician.
Never use outside or in any location where
exposure to water or high humidity may occur.
Do not touch the power cord or electrical outlet
with wet or dirty hands. Doing so may result in
electrical shock.
Be aware of your surroundings and use
cautiously with children around. Swinging
the club during play without being aware
will result in serious injury or death.
Conduct play in a clean and brightly lit
location. Operating in a dark or cluttered
space may lead to accidents.
Install in a level and stable location.
Failure to do so may result in falling of
the machine, leading to injury.
Safety
Cont.
This is a heavy machine.
WARNING!

QED USER MANUAL 5
* AMD: 3rd gen Ryzen or higher and AMD Ryzen 3600 or higher (AMD 2700 is not compatible).
Installation Environment
Category Requirement
CPU Intel i5 8400 or higher*
RAM 8 GB
Graphics Card GeForceGTX 1060 or higher
Operating System Windows 10 (64bit) Version 1803 or higher
Resolution 1920 x 1080
Connectivity Ethernet Port Required

QED USER MANUAL 6
Club Stickers
Ethernet LAN
Cable Level
USB Ethernet
Adapter
What’s Included
The following items are included with the sensor. Make sure
they are all present and accounted for.
Bracket Calibration ChartQED Sensor Bar
Power Cable
Power
ConnectorPower Adapter
M4 32mm screws M6 15mm screws

QED USER MANUAL 7
Hardware Install
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly. Material damage refers
to damage to home, furnishing, or
anything within the unit’s vicinity.
This symbol alerts the user to items
that should never be carried out.
Used for instructions intended to alert
the user to the risk of severe injury
should the unit be used improperly.
Ladder Phillips
Screwdriver
M4 32mm
Screw x9
Bracket Sensor Bar
NECESSARY TOOLS NECESSARY PARTS
WARNING
WARNING
CAUTION

QED USER MANUAL 8
Hardware Install
Mounting Bracket
The QED Sensor and bracket
come attached together in the
box. Slightly loosen the black M6
15 mm screws that are holding
the sensor to the bracket so
you can remove it. Please make
sure you have measured 3.5
feet from the front of the sensor
to your tee position. Do NOT
align to the bracket. The QED is
mounted 3.5’ behind the center
of the hiting arera.
1
Place the ladder under the
location on the ceiling where
the bracket will be mounted.
Place the bracket at against
the ceiling with the hinges
facing down toward the ground.
The side with the Uneekor logo
should be closest to the impact
2
With the bracket in position, grab
the 10 silver M4 32mm screws
and screw them in the locations
below in the diagram.
3
Step 1: Mount Bracket

QED USER MANUAL 9
Hardware Install
Insert Sensor
Step 2: Insert Sensor
After the bracket has been rmly mounted to the ceiling, you will install
the sensor bar.
The sensor bar comes with 6 black M6 15mm screws already inserted; 3
screws in the front and 3 screws in the back. Make sure all 6 screws are
about halfway into the bar and even in length.
1
Slide the sensor bar with the 6 screws up and over through the bracket
hinges. Make sure the screws are secured in the hook part of the hinges.
Once the sensor is secured in the bracket hinges, tighten the 6 screws to
the bracket.
2

QED USER MANUAL 10
Hardware Install
Connection
Take out the Ethernet LAN cable from the box. Connect the end with the
tag that reads “Connect this side of LAN cable to Sensor ONLY” to the
sensor. Connect the other end DIRECTLY to your PC ethernet port and
NOT the USB adapter.
1
Take out all 3 components of the power source: power cable, power
adapter, and power connector. Connect all 3 accordingly and connect the
“Power Connector” end directly to the sensor as shown below. Turn on red
switch.
2
Step 3: Connection
Note: The plug must be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
An extra green grounding wire is provided on the end of the power connector in
case your outlet is not grounded.
**Make sure to check the connection status before you start the software
installation process.
Ethernet LAN
Cable
Power Cable Power
Connector
Power
Adapter
NECESSARY PARTS
Power
Connector
Ethernet
LAN

QED USER MANUAL 11
Tech Requirements
LAN Cable
(Ethernet)
Sensor
It is important before you start the network setup process, that you have
the sensor bar powered on and connected to your PC with the LAN cable
provided to you in the shipping box.
Make sure the LAN cable is DIRECTLY connected to your PC in the back
Ethernet port. Do NOT have it connected to the USB Adapter or a hub.
Hardware Install
Step 4: Connection Status
Page 14 Diagram 1 - EYE-MINI Manual Diagrams
*Not sure about this computer graphic...
we could buy a stock image or I can
make one if we want to replace it
PC

QED USER MANUAL 12
Software Installation Warning
Please make sure the connection
statuses are clear and everything
is paired. Failure to do will result in
installation issues.
Please make sure PC requirements
are met from section 1 “Installation
Environment,” before the installation
process. Failure to do will result in
installation issues and slow gameplay.
WARNING
WARNING

QED USER MANUAL 13
Uneekor Launcher
Software Installation
To begin the software installation for your QED. Please download the
Uneekor Launcher found under the resources tab of Uneekor.com or use
the link below.
Uneekor Launcher
For further information on using the Uneekor Launcher, please see below.
Overview Guide
1
After downloading the launcher,
create an account by clicking “Create
your Uneekor Account.” If you already
have an account, select sign in.
2
Go to the “Install” tab on the left side
of the launcher and select the QED,
then continue.
For the remainder of the software
installation, please follow the step-by-
step guide on the Launcher.
If you have any issues with
installation, please see the next two
pages.
3

Software Installation - Cont
Uneekor Launcher
Ensure your QED is plugged into
the power, and the CAT6 cable is
connected from the QED directly
into the Ethernet port on your PC. If
connected using the USB 3.0 adaptor,
you’ll run into issues using the QED.
If these conditions are met, click
“Continue.”
4
If you only have one Ethernet port
on your PC, then you should only
have one option for the selection of
Ethernet ports.
If you have 2 or more Ethernet ports,
select the Ethernet port your QED is
connected to in the drop down and
click “Select.”
Once the proper Ethernet port is
selected, press “Continue.”
5
QED USER MANUAL 14

Software Installation - Cont
Uneekor Launcher
QED USER MANUAL 15
6
You will see your QED here. Click
“Select” and then “Continue” on the
bottom.
If you do not see your QED press the
“Refresh” button.
If your QED still does not appear return
to step 5 and select a different Ethernet
port and click “Select.”
If you continue having issues, please
power off your QED. Then ensure your
QED is connected properly connected
to your PC and power outlet, and then
close and reopen the Uneekor Launcher
to start the installation process over.
7
You may enter license keys manually using
the box under 1. (Swing Optix, Rene/+, and
Balance Optix)
Under 2, your 3rd Party Connector, View, and
Rene+ 30-Day Trial will already be present.
Individually select which licenses you would
like to activate using the box on the left or you
can press the “Select Keys for Current Device”
to activate all keys associated with your QED.
Make sure to press “Activate” under 3. and
then press “Continue.”
Hardware installation is now complete. The
next steps will walk you through calibration.

QED USER MANUAL 16
CALIBRATION GUIDE
Level
Tool required
Calibration Chart
Parts required
Uneekor Launcher
Software required

QED USER MANUAL 17
To Ensure Safe Use
The mounting position of the QED sensor
must be perfectly aligned 3 feet 6 inches
behind the center of your tee position and
between 9 - 10 feet for the ceiling height.
Failure to meet these requirements will
result in accuracy issues.
Conrm you have successfully nished
the hardware and software installation
before you begin the calibration process.
WARNING
WARNING

QED USER MANUAL 18
Calibrating
During the installation process of the QED using the launcher, it
will automatically pull up the calibration tool.
Please follow the prompts on the launcher to calibrate your QED. If
you have any issues calibrating your device using the instructions
on the launcher, please see the next page.

QED USER MANUAL 19
Calibrating
During Step 6 of the installation
process, the calibration tool on the
right will open. Please follow the
prompts on the screen. If you have any
issues than see the remaining steps
below.
Lay the calibration board at and
ensure the calibration board is within
the red squares on all 3 windows.
*Ensure there are no other objects
visible in each camera view when
calibrating your launch monitor.
Step 1
Next, place the bubble leveling tool on the
calibration board to conrm that the hitting
mat is level front to back and side to side.
Step 2
Before pressing “Calibrate” below the rst
camera window, make sure the top of
the calibration board is parallel with the
impact screen and nothing other than the
calibration board is visible in the calibration
tool.
If all the above conditions are met, click
“Calibrate” on the bottom left.
Step 3
Uneekor Launcher