unGer Rinse'N'Go Max User manual

1
User Manual
Read carefully for safety, assembly
and operating instructions prior to
using this product.

2
TABLE OF CONTENTS
DANGER
READ USER MANUAL BEFORE USING PRODUCT
Introduction.......................................................................................................................... 3
1.0 Safety Information ................................................................................................. 4-5
2.0 System Products & Accessories......................................................................... 6-9
3.0 Assembly Instructions.............................................................................................10
4.0 Use and Operation............................................................................................11-12
5.0 Pure Water Production............................................................................................13
6.0 System Maintenance - Replacing Resin Filter & Care ..........................14-16
7.0 Storage .........................................................................................................................16
8.0 Environmental Information ..................................................................................16
9.0 TDS Meter....................................................................................................................17
Product Guarantee...........................................................................................................18
CONTENTS UNDER PRESSURE. CAN CAUSE SEVERE INJURY OR DEATH
FROM TANK RUPTURE. THIS PRODUCT CONTAINS A BUTTON BATTERY.
IF SWALLOWED, IT COULD CAUSE SEVERE INJURY OR DEATH IN JUST
2 HOURS. SEEK MEDICAL ATTENTION IMMEDIATELY.
WHEN STARTING SYSTEM
• WATER OUTPUT MUST BE OPEN WHEN FILLING.
• DO NOT EXCEED PRESSURE OF 115 PSI (8 BAR).
• CHECK SYSTEM FOR CRACKS.
• BE SURE COVER IS IN LOCKED POSITION.
• KEEP WATER OUTPUT OPEN AND HOLD YELLOW FASTLOCK™
LEVER DOWN TO REMOVE TRAPPED AIR FROM SYSTEM.
• FOR USE ONLY WITH TAP WATER.
BEFORE SERVICING SYSTEM
• SHUT OFF TAP WATER SUPPLY AND OPEN WATER OUTPUT.
• DISCONNECT WATER SUPPLY AND ALLOW TANK TO DRAIN.
SPILLED RESIN IS A SLIPPING HAZARD.
CLEAN UP SPILLED RESIN IMMEDIATELY.
RESIN CAN CAUSE SKIN IRRITATION
• AVOID SKIN CONTACT.
• WASH HANDS THOROUGHLY AFTER USE.
• CAN CAUSE EYE IRRITATION.
• AVOID EYE CONTACT.
• WEAR SAFETY GOGGLES.
• IN CASE OF EYE CONTACT, IMMEDIATELY FLUSH EYES
THOROUGHLY WITH CLEAN WATER.
• CONSULT DOCTOR IF SYMPTOMS PERSIST.

3
INTRODUCTION
Thank you for your purchase of the Unger Professional Rinse 'N' Go Max™
system. This manual will help you get set up and begin using your product right
away. When used as intended, this system will produce low total dissolved solids
or TDS (less than 20 ppm) pure water for auto, boat, RV and solar panels.
The science behind this product is called deionization, or ion exchange.
In this process, the minerals responsible for leaving spots on your vehicle and
windows are removed from the water. So, you can rinse the surface, walk away,
and still get spot-free and streak-free results. This water is meant to be used for
the nal rinse of your vehicle. You still need to wash dirt and grime off of your
vehicle as you would normally do when washing your vehicle. However, instead
of spending all of that time drying it by hand, you can rinse the vehicle with this
water and just walk away.
The Unger Professional Rinse 'N' Go Max™ system contains mixed bed ion
exchange resin to remove impurities out of ordinary tap water, turning it into
what is commonly referred to as pure water. Such impurities are referred to as
total dissolved solids (TDS) and are measured in parts per million (ppm).
Water is considered 100% demineralized or pure when its TDS is measured
at 0 ppm. The average TDS of drinking water is 180 ppm (see table in section
5.0). Pure water left on the surface will dry to a clean and spot-free appearance.
No power is required other than the tap water line pressure, which typically
ranges from 40-60 psi. This enables the system to produce pure water
at approximately 1.5 gallons per minute. Unger recommends testing the water
supply (TDS) before using this product at a pressure that does not exceed
115 psi (see section 4.0 for more information).
Mixed bed ion exchange resin eventually becomes exhausted and no longer
able to remove impurities. A TDS meter is included with the system to measure
the TDS level in the water that comes out of the system. TDS is a measure of
how pure the water is. Water that contains a TDS of less than 20 ppm should not
leave spotting on the car. The TDS must be less than 10 ppm for spot-free glass.
When TDS levels reach over 20 ppm the resin lter should be replaced.
Changing the resin lter is quick and easy (See section 6.0).

4
1.0 SAFETY INFORMATION
Prior to product assembly and start-up, it is essential that you observe the safety
information and instructions for installation and maintenance contained in this
manual. Unger is not liable for damage to application areas, plumbing system
components or persons. Unger is not liable for misuse or mishandling of the
product, including dropping, dragging or dismantling.
As with any equipment, care must be taken when operating and servicing the unit.
There is a risk of damage to the system due to:
• Operating and installation errors.
• Use of loose resin (overll and expansion of resin will damage unit).
• Vessel is opened incorrectly.
• Using non-Unger spare parts.
• Performing unauthorized modication to unit.
• Insufcient maintenance.
1.1 GENERAL WARNINGS:
• Never direct water towards eyes or face.
• KEEP OUT OF REACH OF CHILDREN AND PETS. Do not allow product to be
used as a toy. Close supervision is necessary when any appliance is used by or
near children.
• To prevent electrical shock, do not use near any sources of electricity, including
electric and power lines.
• Do not use on electrical equipment or appliances.
• After unpacking the product, be sure to carefully dispose of any plastic bags to
avoid injury.
• Use only as described in this manual.
• Use only manufacturer’s recommended attachments.
• Be sure cover is in locked position prior to use.
• Do not exert excessive pressure on release mechanism as breakage may occur.
• Drain the water from the unit after each use.
• Do not allow unit or resin to freeze.
• Ensure work area has sufcient water drainage.
• Turn off water supply when not in use.
• Do not drink water produced by this product.

5
1.2 WHEN STARTING SYSTEM:
• For use only with tap water.
• Do not connect to pressure washer or auxiliary pump.
• Do not exceed water pressure of 115 psi.
• Check system for cracks/damage.
• Be sure cover is in fully locked position.
1.4 INTENDED USE:
This product is designed for personal use only. Always ensure that the product
is properly assembled, regularly maintained and used only as intended.
This product is meant to be used outside and stored at a temperature between
40°F - 100°F. Use this device only for water treatment to reach an optimal water
quality for spot-free cleaning. Any other use, especially water treatment for
food production (e.g., beverages) or drinking water consumption is prohibited.
Prior to product assembly and start-up, it is essential that you observe the safety
information and instructions for installation and maintenance contained in this
manual. Unger is not liable for damage to application areas, plumbing system
components or persons. Unger is not liable for misuse or mishandling of the
product, including dropping, dragging or dismantling.
As with any equipment, care must be taken when operating and servicing the unit.
There is a risk of damage to the system due to:
• Operating and installation errors.
• Use of loose resin (overll and expansion of resin will damage unit).
• Vessel is opened incorrectly.
• Using non-Unger spare parts.
• Performing unauthorized modication to unit.
• Insufcient maintenance.
1.1 GENERAL WARNINGS:
• Never direct water towards eyes or face.
• KEEP OUT OF REACH OF CHILDREN AND PETS. Do not allow product to be
used as a toy. Close supervision is necessary when any appliance is used by or
near children.
• To prevent electrical shock, do not use near any sources of electricity, including
electric and power lines.
• Do not use on electrical equipment or appliances.
• After unpacking the product, be sure to carefully dispose of any plastic bags to
avoid injury.
• Use only as described in this manual.
• Use only manufacturer’s recommended attachments.
• Be sure cover is in locked position prior to use.
• Do not exert excessive pressure on release mechanism as breakage may occur.
• Drain the water from the unit after each use.
• Do not allow unit or resin to freeze.
• Ensure work area has sufcient water drainage.
• Turn off water supply when not in use.
• Do not drink water produced by this product.
1.3 BEFORE OPENING SYSTEM TO REPLACE RESIN:
1. Shut off tap water supply.
• Spilled resin is a slipping hazard. Clean up spilled resin immediately.
• Wash hands thoroughly after use.
• Resin can cause eye irritation. Avoid eye contact. In case of eye contact, immediately ush
eyes thoroughly with clean water. Consult doctor if symptoms persist.
3. Turn ON/OFF valve to “OFF” position.
2. Press yellow FastLock™ lever on
system head assembly.
4. Disconnect outlet hose.
Bottom
Top

6
2.0 SYSTEM PRODUCTS & ACCESSORIES
NOTE: When unpacking the product, make sure that no accessories are missing
and that none of the package contents have been damaged.
RINSE 'N' GO MAX™ DEIONIZATION SYSTEM OVERVIEW
This product can be connected to traditional garden hoses and used with
conventional car and window cleaning tools of your choice.
Resin lter tank
Handle
FastLock™ lever
(Yellow)
Handle
OUTLET CONNECTION
QuickChangeTM
Resin Filter Bag
(Packed inside unit)
Outlet
Connection plug
ON/OFF valve
INLET CONNECTION
System Head Assembly
Base
(Water out)
(Water in)

7
SOAP BLASTING NOZZLE OVERVIEW
Spray delivery
Soap container
Flow control
knob
Spray pattern
selector
Locking
trigger
TDS METER OVERVIEW
Battery
compartment
Hold
Maximum immersion level
TDS meter electrode
LCD
Temperature
On/Off
Protective cap
Soap Blasting Nozzle
connects to the outlet
hose (not provided)

8
SYSTEM PRODUCTS & ACCESSORIES
WATER-FED POLE & SOFT WASH BRUSH
Water-fed pole
Water-fed
soft wash brush
Water ow
ON / OFF
valve
Non-slip grip foam
Pole connects to the
outlet hose (not provided)

9
WATER-FED POLE & SOFT WASH BRUSH
INLET HOSE AND CONNECTION PLUGS
Water supply hose connects
to the inlet connection
(ON/OFF valve)
Water supply hose
Garden hose
(not provided)
QUICK CONNECT PLUGS
Water supply hose
ON/OFF valve
Inlet Adapters Outlet Adapters
Outlet
garden hose
(male plug)
Outlet female plug
Water supply hose
(provided)
Inlet plug
(male plug)

10
• Unpack Unit: Inspect the Unger
Professional Rinse 'N' Go Max™ system
and all components to ensure there are
no cracks or other damage. Read all
warnings and manual.
• Ensure there is a resin lter inside the
unit. (For instructions on how to open
the unit, see section 6.0).
• Water INPUT connection must always
be at the bottom (base) of the unit.
• Water OUTPUT connection must always
be at the top of the unit. This is the hose
that delivers ltered water.
3.0 ASSEMBLY INSTRUCTIONS
WATER OUTPUT
WATER INPUT
(Water supply)
(Connects to Soap Blasting
Nozzle or Water-fed Pole)
If leaking or dripping occurs around
the hose connections, re-tighten
the connections by hand.

11
Unger recommends testing the water supply for TDS prior to use in order to
determine approximately how many times you can rinse your vehicle before
replacing the resin lter.
INSPECT THE RINSE 'N' GO MAX™ SYSTEM PRIOR TO USE
Inspect system for leaks, cracks, or dents and proper t of top cap assembly.
Ensure hoses are properly attached and there are no leaks.
PREPARE THE SYSTEM FOR USE:
1. Locate water supply.
2. Set up system in upright position.
3. Choose a stable location where product is securely on the ground to
minimize toppling.
4. Connect water supply hose (provided) to inlet connection at the bottom of the unit.
5. Connect garden hose (not provided) to outlet connection.
4.0 USE AND OPERATION
Product needs to be upright for water to ow through resin.
If the product is on its side, water won’t ow through resin correctly,
resulting in spots and/or streaks.

12
1. Fill container with your favorite concentrated car wash shampoo (do not add water).
2. Attach the spray nozzle to your garden hose.
WASHING YOUR VEHICLE USING THE RINSE 'N' GO MAX™ SYSTEM
• Wash your vehicle using our Soap Blasting Nozzle and water-fed pole and brush.
• Using the Rinse 'N' Go Max™ system, rinse your vehicle with pure (deionized)
water. If using the Soap Blasting Nozzle, turn the ow control knob to the water
only setting to ensure you don’t continue adding soap to the vehicle.
• Make sure to rinse every part of the vehicle with the water, including areas where
soap might get stuck, for example, around trunk, lights, fuel door and other seams.
• For best results, rinse the vehicle twice to remove all soap and ensure spot-free results.
• You’re done! No need to hand dry your vehicle. The puried water does all the
work for you so that your vehicle will dry completely spot-free! Just like if you
had it cleaned professionally.
4.0 USE AND OPERATION (CONT.)
USING THE TDS METER
1. Remove the protective cap.
2. Press the ON/OFF button to turn the meter on.
3. When water begins to ow out of the unit, ll the protective
cap with the water.
4. Insert the meter into the capful of water for 5 seconds.
5. The LCD will indicate the ppm level of the water.
6. Press the HOLD button in order to view the LCD when meter is
removed from the water.
7. Press the ON/OFF button to turn the meter off.
8. Dry the meter completely before replacing the protective cap.
When the TDS meter shows a reading of 20 ppm or higher,
spotting may occur and it is recommended that the resin lter
be replaced.

13
5.0 PURE WATER PRODUCTION
Tap water ows into the system’s lower connection port via tap pressure and
ows upwards through the Rinse 'N' Go Max™ tank. Pure water exits through the
top connection. When plumbing line pressures fall below 40 psi, a reduction in
ow rates will be noticeable.
The type of tap water you run through the system will impact how long you are
able to use the purifying resin lter before seeing spots and streaks. This is often
referred to as hard water. All water starts as soft water but the level of minerals,
such as magnesium and calcium, that are in the ground impact how hard the
water will become.
Soft water has a TDS reading of 100 ppm or less, while some regions with very
hard water have a TDS reading of 400 ppm or greater. This product is meant to
last 24 rinses with an average TDS reading of 200 ppm. To test the ppm level of
your water, you can use the TDS Meter to measure the water coming directly out
of the tap.
When washing your vehicle, we recommend using the pure (deionized) water
from the Rinse 'N' Go Max™ system for the rinse portion of the process only.
You can use the pure water to apply the soap and wash your vehicle, but you will
run through resin faster and it will not improve results.
Water TDS Reading Avg. # of rinses per
Resin Filter*
Soft <100 ppm 24-30
Medium 100 – 250 ppm 24-30
Hard 250 – 400 ppm 10-15
Very Hard 400 – 450 ppm 6-10
*All values based on 20 ppm as a maximum for pure water quality and an
average vehicle rinse time of 5 minutes.

14
Unger does not recommend the use of any other resin except that which is
made specically for the Unger Professional Rinse 'N' Go Max™. The use of
any other resin may cause damage to the system.
Prior to removing hoses, and prior to any long term storage, manually
actuate the yellow FastLock™ lever to remove any built up pressure from
within the unit.
AFTER EACH USE
1. Shut off tap water supply.
2. Press yellow FastLock™ lever on system head assembly.
3. Disconnect hoses from both ends of the unit.
4. Drain water from the unit by tilting the top of the unit forward and allowing
water to drain from the bottom of the tank, via the input connection.
5. Replace plug on both the inlet and outlet connection to prevent the resin
from drying.
6.0 SYSTEM MAINTENANCE AND CARE
Outlet connection plug (red)
Intlet connection plug (yellow)

15
1. First shut off tap water supply, then press yellow FastLock™ lever on system
head assembly. Turn ON/OFF Input connector (at the bottom of the unit) to “OFF”
position and disconnect output hose (at the top of the unit).
2. Press yellow FastLock™ lever on system head assembly, while continuing pressing the
yellow lever, use a counterclockwise quarter-turn to release system head assembly.
Reach into tank and remove the bag by lifting it out of the unit, discard according
to local regulations. Never remove resin from the nylon bag.
4. Re-attach system head by pushing down rmly and
turning a quarter-turn clockwise.
OPENING THE UNIT AND REPLACING THE RESIN FILTER
3. Drop new resin lter bag into the tank, zip-tie facing up. You may need to pat
down by hand to ensure the entire bag ts well inside the chamber.

16
7.0 STORAGE
1. Shut off tap water supply and disconnect hoses from both ends of the unit.
2. Drain water from the unit by tilting the top of the unit forward and allowing
water to drain from the bottom of the tank, via the input connection.
3. Replace plug on both the inlet and outlet connection to prevent the resin
from drying.
The system should be stored in a dry place at a temperature between
40°F - 100°F. Do not allow product to freeze or damage might occur.
Storing the product in an upright position is recommended. If storing the
product for longer than 6 months without using, remove the resin and discard
it in accordance with applicable federal and local laws and regulations .
Also remove batteries from TDS Meter.
• Do not store resin in open or unlabeled containers.
• Store resin in a cool (40°F - 100°F), dry place.
CARE MUST BE TAKEN WHEN OPERATING AND SERVICING THIS PRODUCT.
THERE IS A RISK OF DAMAGE TO THE SYSTEM DUE TO:
• Operating and installation errors.
• Use of resin lter other than that specically made for Unger Professional
Rinse 'N' Go Max™ system.
• Use of loose resin (loose resin will most likely cause clogging and reduce ow rate).
• Pressure is not released correctly.
• Performing unauthorized modication to product.
• Improper maintenance and storage: Never store below freezing. Always seal unit
(inlet and outlet) between uses using plugs to prevent resin from drying out.
• The outer packing material can be recycled. Please recycle.
• Please dispose of used resin lter in accordance with applicable
federal, state/provincial and local laws and regulations.
8.0 ENVIRONMENTAL INFORMATION

17
KEEP BATTERIES OUT OF REACH OF CHILDREN
Swallowing may lead to serious injury or death in as little as 2 hours, due to chemical
burns and potential perforation of the esophagus. If you suspect your child has
swallowed or inserted a button battery, immediately seek urgent medical assistance.
HOW TO REPLACE THE BATTERIES:
• Pull open the battery compartment.
• Insert new batteries as indicated inside the battery compartment with the
positive and negative sides aligned.
• Replace both batteries at the same time (1.5V ‘LR44 type’ button batteries).
Do not mix old and new batteries or different battery types.
• Use only two 1.5V ‘LR44 type’ button batteries.
• Close battery compartment securely.
• Dispose of used batteries properly and immediately.
9.0 TDS METER
WARNING
BATTERIES
The TDS meter contains two button batteries. If swallowed, could cause severe
injury or death in just 2 hours. Seek medical attention immediately.
The TDS meter model HS-1510 included with the system is to measure the Total
Dissolved Solids (TDS) level in the water that comes out of the Rinse 'N' Go Max™
system. TDS is a measure of how pure the water is. Water that contains a TDS of
less than 20 ppm should not leave spotting on the vehicle. The TDS must be less
than 10 ppm for spot-free glass.
• The outer packing material can be recycled. Please recycle.
• Please dispose of used resin lter in accordance with applicable
federal, state/provincial and local laws and regulations.
Remove batteries from TDS Meter if you do not plan to use it for more than 6 months.

18
We design and test Unger products to ensure they meet our high quality
standards. We support this with the Unger Professional Product Lifetime
Guarantee. We will replace your Unger Professional Rinse 'N' Go Max™
system if it does not meet our high quality standards for material, construction,
or workmanship.
THE GUARANTEE DOES NOT COVER:
• Damage caused by using the product in a commercial enterprise.
• Failing to follow Unger’s use and maintenance instructions.
• Operating and installation errors.
• Opening/disassembly of housing other than by Unger (except resin
replacement as described in section 6.0).
• Replacing connections and components or performing unauthorized
modications other than by Unger.
• Use of the system at more than 115 psi.
• Use of this product with a pressure washer or auxiliary pump.
• Replacement of purifying resin lters.
UNGER IS NOT LIABLE FOR THE FUNCTION OF THE PRODUCT WHEN:
• Use is not in accordance with product instructions.
• Failing to comply with safety instructions.
If you believe that your Unger Professional Rinse 'N' Go Max™ system does
not meet the guidelines as described for the Unger Professional Lifetime
Guarantee, please contact us at 1-800-833-6100. Unger may, at its discretion,
require return of the product for examination and testing. If a replacement
product is no longer available, Unger will replace your product with one of
equal or greater retail value at its sole discretion.
PRODUCT
LIFETIME GUARANTEE

19
PRODUCT
LIFETIME GUARANTEE
Thank you for using

20
Unger Industrial, LLC
425 Asylum Street Bridgeport, CT 06610
[phone]
www.ungerpro.com
™