UNIARCH SW-2106-P User manual

PoE Networking Solution
User Guide
4*10/100Mbps+2FE PoE Switch

Package Contents
Check the following contents of your package:
PoE Switch ×1
User Guide ×1
Power Cord ×1
Accessories(Feet*4)
If any part is lost and damaged, please contact your local agent immediately.
FCC statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
LVD/EMC Directive
This product complies with the European Low Voltage Directive
2014/35/EU and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical &
Electronic Equipment (WEEE) Directive and must be disposed of in a
responsible manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery Directive
2013/56/EC. For proper recycling, return the battery to your supplier
or to a designated collection point.

Introduction
The switch provides the seamless network connection. The PoE ports (Port1~4) can automatically detect and
supply power with those IEEE 802.3af/at compliant Powered Devices (PD). The electrical power is transmitted
along with date in one single cable allowing you to expand your network where there are no power lines or
outlets, where you wish to fix devices such as AP, IP Phones, etc.
It is easy to install and don’t need to configuration. With outstanding performance and quality, the 6-port
10/100Mbps desktop PoE switch is an ideal choice for expanding your home or office network.
Hardware Description
Front Panel
The Front Panel of the switch consists of 6-port 10/100Mbps Ethernet RJ45 Ports. The LED indicators are also
located on the panel.
DIP Switch
The DIP switch located on the left panel.
Default mode: When Extend closed the factory default mode can normal communication between port 1~6.
Extend: 1-4 port can be isolated each other but 1-4 port can connect to 5, 6 ports after open extend to stop
broadcast storm to increase forwarding rate of frame. The extend mode, up to 250m PoE distance allows you to
expand you network via Ethernet cable to where there is no power line or outlet but where you want to fix
device such as IP Cameras.
Note: After change the mode, in order to make the corresponding configuration take effect you need to manually
restart the PoE switch.

LED indicator
LED
Color
Function
PWR
Orange
Off: No Power supply.
Light: Indicates the switch has power.
DATA
Green
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully
established at 10/100Mbps.
Blink: Indicates that the switch is actively sending or
receiving data over that port.
PoE
Orange
Off: No PoE powered device (PD) connected.
Light: There is a PoE PD connected to be port, which
supply power successfully.
Blink: Indicates port abnormal power supply
Rear Panel
The rear panel of the switch indicates AC inlet power socket.
Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the following
instructions in avoid of incorrect installation causing device damage and security threat.
①Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet cloth or liquid;
②Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis;
③Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall;
④Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction;
⑤Make sure that the operating voltage is the same one labeled on the switch;
⑥Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks.

Desktop Installation
Install the switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each
corner of the switch in case of the external vibration. Allow adequate space for ventilation between the device
and the objects around it.
Wall-mounted installation
In the first two fixed screw on the wall as shown in the figure below
Aim at the two fixed hole switches, and the machine smoothly on the screw
Turn on the switch
The PoE switch can be used with AC power supply. Powering on the switch, it will automatically initialize and its
LED indicators will respond as follows:
Firstly, the Power LED indicator will light up.
Then, the data LED indicators will flash momentarily for one second, which represents a resetting of the system.

Specifications
Model
4*10/100Mbps+2FE PoE switch
Standard
IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3af, IEEE802.3at
Network Media(Cable)
10BASE-T: UTP category 3, 4, 5 cable (≤100m)
100BASE-Tx: UTP category 5 cable (≤100m)
MAC Address Table
2K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10BASE-T: 14881pps/Port
100BASE-Tx: 148810pps/Port
Switching Capacity
1.2G
Dimensions(L*W*H)
168*93*32mm
Fan
Fanless
Power Supply
65W built-in
PoE Port
Port 1~4
PoE Power on RJ45
Mode A 1/2(+),3/6(-)
PoE Power Output
32W(Max)
PoE Power Budget
65W
Temperature
Operating Temperature: 0℃~40℃(32℉~104℉)
Storage Temperature: -40℃~70℃(-40℉~158℉)
Humidity
Operating Humidity: 10% ~90% non-condensing
Storage Humidity: 5%~90% non-condensing