Unimac Airdrlumcak06 User manual

6 PC. Air Drill Kit

User Manual

[Revision 3.0 October 2018]

RETAIN THIS MANUAL FOR FUTURE REFERENCE

PLEASE READ THIS MANUAL CAREFULLY BEFORE USE

6 PC. Air Drill Kit

Table of Contents

Safety.................................................................................................................................................................1

Particular Safety Instructions.........................................................................................................................2

Set-Up ................................................................................................................................................................3

Operating Controls Chuck .............................................................................................................................3

Forward/Reverse Selector.............................................................................................................................3

Trigger ..........................................................................................................................................................3

Operation...........................................................................................................................................................4

Operational Hints ..........................................................................................................................................4

Maintenance ......................................................................................................................................................4

6 PC. Air Drill Kit

Safety

WARNING: Some dust created by power sanding, sawing, grinding and other construction activities contains

chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples off these

chemicals are lead from lead-based paints crystalline silica form bricks, cement and other masonry products

Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending now how often you do this type of work. To reduce your

exposure to these chemicals: work in a well-ventilated area, and use approved personal protective equipment,

such as dust masks that are specially designed to filter out microscopic particles.

•Keep work area clean. An untidy and cluttered work area increases the risk of accidents.

•Use personal protection equipment. Always use safety glasses or goggles. A facemask should also be worn

when dust is generated. A respirator should be worn when spray painting, even when using outdoors.

•Wear suitable work clothes. Don't wear loose fitting clothes or jewellery. They can be caught in moving parts

and may cause injury. For outdoor work rubber gloves and nonslip footwear are advised. Wear a protective

hair net to contain long hair.

•Take precautions with compressed air. Do not disconnect air hoses or tools when the line is under pressure.

Close off air supply and release pressure first. Do not point tools or direct compressed air at people or

animals.

•Observe work area environment. Do not expose air tools to rain or wet conditions. Do not use air tools in

close proximity to flammable liquids or gases. The work area should be well lit and ventilated.

•Keep pets, untrained operators and children away. Children should be kept away from the work area. Do not

permit them to handle the tool or tool cable.

•Secure the work pieces. Use clamps or a vice to hold work. This will free up both hands to operate the tool,

which is safer.

•Don't overreach when working. Keep a balanced footing at all times. Avoid abnormal stances and awkward

body positioning.

•Do not overload or force tools. Tools operate better in the specified performance ranges. Forcing the tool

may cause motor damage.

•Check for damage. Before further use always check the protection guards carefully to ensure proper

operation and performance. Check for alignment of moving parts, binding of moving parts, breakage of parts,

mountings and any other condition that may affect the tools operation. If the tool suffers severe impact, a

crack or damage may occur do not use a tool if a crack develops or if air is escaping.

•Use the right tool. Only use air tools for their intended purpose. Do not force a small tool or accessory to do

the job of a heavy-duty tool. Do not exceed recommended air pressure.

•When changing tools or accessories. Always close off air supply and release pressure before attempting to

loosen any connection.

•Beware of temperature extremes. The expanding air causes the air tools to run very cold. Light gloves are

advisable for operator comfort. Conversely, the cylinder head and air delivery pipe of the compressor tank

will run quite hot, avoid contact with these.

•Maintain tools with care. For efficient and safe operation tools should be kept clean. Check the connections

and hoses. If damaged they should be replaced.

•Avoid unintentional triggering. Do not carry tool or connect them with your finger on the trigger.

•Don't over-use hoses. Do not carry tools by the hose or use the hose to drag the compressor. Protect hoses

from heat, oil and sharp objects. Avoid draping the hose over the compressor cylinder head.

•When not in use, your air tools should be stored in a dry area, which is not accessible to children.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

6 PC. Air Drill Kit

•Stay alert. Do not use the tool when you are tired or under the influence of alcohol and drugs. Use common

sense and watch what you are doing or serious injury will occur.

•Remove keys and spanners. Do not forget to remove any adjustment keys, spanners and wrenches before

switching on the tool.

•Don't leave unattended. Do not leave the compressor operating while unattended for extended periods of

time. If you have finished using the compressor and associated tools, switch off supply and remove the plug.

•Use only compressed air. This tool is intended for use with compressed air only. Never attempt to operate

the tool using compressed bottled oxygen or combustible gases.

Particular Safety Instructions

•Shut off air supply and release pressure when changing bits.

•Only operate this tool within the recommended pressure range 60 90 PSI. Use outside this range will cause

poor performance, excessive wear and possible danger.

•Safety glasses must always be worn for eye protection. Hearing protection is strongly recommended when

operating for long periods.

NOTE: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all

possible conditions and situations that may occur. It must be understood by the operator that common

sense and caution are factors that cannot be built into this product but must be supplied by the

operator.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

6 PC. Air Drill Kit

Set-Up

NOTE: If you are not using an automatic oiler system, before operation, add a few drops of Pneumatic

Tool Oil to the airline connection. Add a few drops more after hour of continual use.

1. You will need to prepare a 1/4" air connector (not included) to connect to the air inlet on the cut-off tool. First,

wrap the 1/4" air connector with pipe thread seal tape (not included) before threading it into the inlet.

Connect the 3/8" ID air source hose (not included) to a quick-disconnect coupler (not included) and then to

the cut-off tool.

2. Set the air pressure on your compressor to 90 PSI. Do not exceed the recommended air pressure of 90 PSI.

3. Check the air connection for leaks.

4. Disconnect from the air hose until next instructed to reconnect.

Operating Controls Chuck

When mounting a drill bit in the chuck, insert bit so that the full shank of the bit is held in the chuck. Tighten the

chuck securely by inserting the chuck key into one of the side holes in the chuck and turning the key clockwise.

Before attempting to drill, check that the bit is held centrally in the chuck jaws and ensure the chuck key is

removed. To release the chuck, insert the key and turn it counter-clockwise.

Forward/Reverse Selector

Push the selector to the "F" position to select normal clockwise rotation. Always drill in this direction. Push the

selector to the "R" position to select counter-clockwise rotation. Do not change direction while drill is in motion.

Trigger

Depressing the trigger will allow the drill to rapidly begin rotation in the selected direction. Release to stop.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

6 PC. Air Drill Kit

Operation

1. Run compressor, adjust compressor regulator for correct operating range of 6090 PSI.

2. Open outlet tap of compressor to connection of drill.

3. Select direction of rotation and press trigger to operate.

4. When changing bits, shut off air supply to tool and release pressure first, to avoid inadvertent operation.

Operational Hints

1. Always ensure that the workpiece is firmly clamped, so that you can use 2 hands to guide and control the

drill.

2. When drilling wood, to prevent splintering on the reverse face when the drill breaks through, clamp a scrap

piece of wood beneath the point where you are drilling.

3. When drilling metals, mark the point to be drilled using a centre punch to assist in starting the hole in the

correct place.

4. To prevent damage to drills, apply some coolant to the bit, but do not wet the tool itself.

5. When drilling wood, plastic, hard rubber or cast iron no lubricant is needed. Use light mineral oil for brass or

bronze, kerosene for aluminium. For steel and other metals use soluble oil.

Maintenance

Always disconnect the air supply before attempting any maintenance.

After disconnecting the air supply, squeeze the trigger to make sure no air remains in the unit.

1. After each use, wipe down the drill with a lint-free cloth. Do not use solvents or harsh detergents to clean the

tool.

2. Make sure the air inlet is clean of dirt, grease, or debris.

If you encounter a problem with operation, stop using the tool immediately. Disconnect tool from air supply

before attempting any adjustment.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

6 PC. Air Drill Kit

Some experts believe that the incorrect or prolonged use of almost any product

may cause serious injury or death. To help reduce your risk of serious injury or

death, refer to the information below. For more information, see

www.datastreamserver.com/safety

Consult all documentation, packaging and

product labelling before use. Note that some

products feature documentation available

online. It is recommended to print and retain

the documentation.

Before each use, check the product for

loose/broken/damaged/missing parts, wear or

leaks (if applicable). Never use a product with

loose/broken/damaged/missing parts, wear or

leaks.

Products must be inspected and serviced (if

applicable) by a qualified technician every 6

months. This is based on average residential

use by persons of average size and strength,

and on a property of average metropolitan

size. Use beyond these recommendations

may require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed access

to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific application or

description of application. Be sure to attain third-party approval

from a qualified specialist for your application before use,

regardless of any assurances from the retailer or its

representatives.

This product is not intended for use where fail-safe operation is

required. As with any product (for example, automobile,

computer, toaster), there is the possibility of technical issues

that may require the repair or replacement of parts, or the

product itself. If the possibility of such failure and the associated

time it may take to rectify could in any way inconvenience the

user, business or employee, or financially affect the user,

business or employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but not

limited to, a condition requiring product return, replacement,

parts replacement or service by a technician may cause

financial loss, loss of employee time or an inconvenience

requiring compensation.

If this product has been purchased in error when considering

the information presented here, contact the retailer directly for

details of their returns policy, if required.

or images may be reproduced or transmitted in any form or by any means, electronic or mechanical, including

photocopying, scanning or recording, or any information storage and retrieval system, without express permission or

consent from the publisher.

Table of contents

Popular Drill manuals by other brands

Festool

Festool T 18+3 Li Original operating manual

DeWalt

DeWalt DCH263 Original instructions

Narex

Narex CSV 13-2 Original operating manual

Bosch

Bosch 1169VSR - 1/2 Inch Dual Torque Double Insulated... Operating/safety instructions

Black & Decker

Black & Decker HP18V instruction manual

Maktec

Maktec MT80A instruction manual

Bosch

Bosch GBH18V-40C Operating/safety instructions

Bosch

Bosch Professional GSR 12V-35 Original instructions

OPTIMUM Maschinen

OPTIMUM Maschinen OPTidrill B17Pro basic operating manual

Milwaukee

Milwaukee 4253-1 Operator's manual

Fein

Fein KBM 50 Q manual

Grizzly

Grizzly G0463 owner's manual

Sealey

Sealey CP108VDD manual

Ryobi

Ryobi RPD1200 Original instructions

Ozito

Ozito PXBHS-100U Original instructions

TBT

TBT ML700 Series manual

Roto Brute

Roto Brute RB32 MINIBRUTE VSR operating instructions

Black & Decker

Black & Decker KR540 user guide

Unimac AIRDRLUMCAK06 User manual

Popular Drill manuals by other brands