Unireach MT18 User manual

1
GPS Tracker
Manual
Model: MT18/MT18B
Preface
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly.
Make sure to read this manual carefully before using this product. Please note that specification and
information are subject to changes without prior notice in this manual. Any change will be integrated in the
latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.

2
1. Summary
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any
remote targets by SMS or internet. The most advanced technology of GPS and AGPS dual positioning. The
waterproof level achieve IPX ‐6.
2. Applications
zVehicle rental / Fleet management etc
zOutdoor sports
zProtect children / elder/ Asset/ pet and so on
zProvide peace‐of‐mind for businessmen
zTracking for Car/truck/container/trailer
zCriminals Tracking
3.Main unit& accessories

3
4.Specs.
5.Userage:
5.1 SIM card installation
1).Open plug
2).Insert simcard
3).Power on tracker
4).Cover plug
Content Specs.
Dim MT18: 120mm x 68mm x 40mm
MT18B: 120mm x 68mm x 33mm
Weight MT18: 188g, MT18B:170g
Network GSM/GPRS
GSM Band 850/900/1800/1900Mhz
GSM chip SIMTK6260
GPS chip UBLOX
GPS sensitivity ‐159dBm
GPS accuracy 5m
Cold start 35‐80s
Warm start 35s
Hot start Hot status 1s
Car charger Input: 12~24V , Output: 5V
Wall charger Input: 110~220V ; Output: 5V
Battery Li‐ion battery :3.7V, 20000mAh(MT18);
3.7V,10000mAh(MT18B)
Standby MT18: 12 months; MT18B: 6 months
Storage Temp. ‐40°C to +85°C
Operation Temp. ‐20°C to +55°C
Humidity 5%‐‐95% non‐condensing

4
5.2 Battery and Charger
‐‐First time to use:Keep in charged the battery over 12 hours Please use the battery and charger provided by
the manufacturer.
‐‐After first use,the battery usually should be charged fully between 3~5 hours.
Cautions:
a: For it’s Li‐ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture it
violently and keep it off fire.
b: Please charge the battery in time to keep it working normally.
6.Startup
1).Power on gps unit:
Insert the SIM card
Turn on the unit outdoors by pressing the Power on button until the indicator is on.
In 10~40 seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signal.
2).Indicators status:
Green LED: GPRS working status
Status Meaning
flashing GSM / GPRS signal fine
On No GSM signal
off GPS power off/In sleep
Blue LED: GPS working status
Status Meaning
flashing GPS signal Fine
on No GPS signal
off GPS power off/In sleep
Red LED for power charging status
3)SMS meanings:
1.Google link: URL
2.V:A GPS signal ok. V:V :No GPS signal
3.2014‐04‐18 02:17:15:GPS Time
4.S:000km/h: Speed of tracker
5.Bat:6:Battery Level（Range :1 ~9）
6.ID:4102000759: ID Number of GPS
Status of indicator Meaning
Red led on Charging
red led flash Low battery
red led off Full battery or charged full

5
7.Operations (Default password: 123456)
7.1.Change password
SMS format: password+old password+space+new password
Example: password123456 666888
it will reply sms: “password OK”
(Note:password should be 6 digits Arabic numbers.There is one space between new&old passwords)
7.2 Set admin phone number:
1).Add admin number:
SMS format:admin123456 0086138********
Note1:The other admin numbers should be set by the first authorized number. If the number is successfully
authorized, the unit will reply “admin ok!” in SMS.
Note2:Note:country code should be added in front of phone number)
2).Delete admin number:
SMS format:noadmin123456 phonenumber
Example:no admin123456 13510460105
Reply sms: noadmin ok
7.3.Track on demand:
SMS format:tracker123456
1).GPS Set with admin numbers: when admin numbers dials up the unit, tracker device will reply by sms,It
wont reply to other numbers
2).GPS without admin numbers: Any cellphone dial up the GPS simcard,tracker device will reply by sms
locations information ,as below:
7.3.Track by GSM Location(Only for admin phone，default:closed）
Command to open :addjz=1
Command to close :addjz=0
8.0.Commands List:

6
Feature name Active Command Reply Cancelother format)
Command
Reply
Add admin
number
admin123456 0086138****
(Note:country code needed
in front of phone
number,there is one space
between password and
phone number)
Admin ok noadmin123456
008618****
noadmin ok
Change
password
password123456 666888 password OK (There is one space between new&old
passwords)
Inquiry Location G123456 Google map link Click on google map link to get location
on map
Voice monitor monitor123456 Monitor ok tracker123456 Tracker ok
Overspeed speed123456 80
(50~120 km/h)
speed ok
(80km/h)
nospeed123456 nospeed ok
Move alarm move123456 500
(100~5000m)
move ok nomove123456 nomove ok
Shock alarm shock123456 shock ok noshock123456 Noshock ok
Sleep in time
mode
Sleep123456 time
(Default model:MT90,MT60)
Sleep time ok If not did any operation,Tracker will be in
sleep mode in 5 minutes,can be woke up
by any calling ,sms and pressing buttons.
Shock sleep
mode
sleep123456 shock
(Default model:MT10)
sleep shock ok
(be in sleep if no
motion)
sleep123456 off sleep off ok
Restart Device RST GPS will restart factory changed be
factory settin
gs
Track by time
points
time1:10:20 ,13:10,15:30,18:
50,20:00#
time2::02:20 ,03:10,05:30,09:
50,11:00#
time3::00:20 ,01:10,03:30,04:
50,06:00#
time4::00:20 ,01:10,03:30,04:
50,06:00#
Time1 set ok
Time2 set ok
Time3 set ok
Time4 set ok
Del,time1#
Del,time2#
Del,time3#
Del,time4#
Time1 deleted
ok
Time2 deleted
ok
Time3 deleted
ok
Time4 deleted
ok
Set Ip and port adminip123456
113.10.245.151 8083
adminip ok If user uses our platform,this step can be
ignored.
Set APN apn123456 cmnet APN OK apnuser123456 user
apnpassword123456
apnpassword
APN OK
GPRS interval
time
upload123456 30
(10~300 seconds)
upload ok upload123456 300 upload ok
Time Zone timezone123456 2 Time ok timezone123456 ‐3Timeok
Language LAG1 Switched to
English
LAG2 Switched to
Chinese

7
9.0 Cautions
9.1 Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry.
9.2 Don’t use & store the unit in dusty places.
9.3 Don’t put the unit in overheated or overcooled places.
9.4 Handle carefully. Don’t vibrate or shake it violently.
9.5 Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
9.6 Don’t paint the unit, this may cause some foreign materials left in between the parts.