URAL Motorcycles RU/MP3-219SA User manual

NCD-7651
INSTRUCTION MANUAL
9141162 31 5 7 10 17
AS /P S
MD
B D/L D
AU X
3
IN T
6
F L +
2
R P T
1
P A U
4
R DM
5
F L -
NCD-7651
CAR PLL AM/FM STEREO RADIO
WITH MP3/WMA/USB/SD/MMC PLAYER
RU/MP3-219SA
INSTRUCTION MANUAL

EN-2
53mm
182mm
Bend these
claws, if necessary
2182mm
53mm
34
TA P
1
1
2
INSTALLATION
PRECAUTIONS
• Carefully choose the mounting location so normal driving is not hindered.
• Avoid installing the unit where it would be subject to high temperatures (direct sunlight or hot
air from the heater) or where it would be subject to dust, dirt or excessive vibration.
• Only use mounting hardware supplied for a safe and secure installation.
• Remove the front panel before installing the unit.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
MOUNTING EXAMPLE
Installation in the dashboard
Note: Keep the release key in the safe place as you may need it in future to remove the unit from
the car.
Detaching and attaching the front panel
The front panel of this unit can be detached in order to prevent theft.
FOLDING DOWN AND DETACHING/ATTACHING THE FRONT PANEL
Before detaching the front panel, be sure to press the
button (1) OFF first
Then press the
button (15), to fully open the front panel. Release the panel by pulling it towards
you as illustrated.
• Do not exert unnecessary pressure on the front panel when attaching it.
• Please use the supplied case when the front panel is removed.
CLEANING THE CONNECTOR
The unit may not function properly if the connectors
between the unit and the front panel are contami-
nated with dirt. In order to prevent this from hap-
pening, detach the front panel by pressing the
button and clean the connector from time to time.
Clean the connector with a cotton swab together
with contact cleaner as illustrated. Be sure to clean
them carefully pin by pin and make sure not to damage the connecting points.
Cotton Swab
Rear of
front panel Main unit
2
1
< 10°

EN-3
10
1
2
3
4
4
5
6
8
7
4
5
6
9
1. UNIT
2. RELEASE CASE
3. DASH
4. HEX NUT
5. LOCK WASHER
6. PLAIN WASHER
7. CAR BODY
8. REAR SUPPORT STRAP
9. TAPPING SCREW
10. M5 X 15 HEX BOLT
TO SUPPORT THE UNIT
WIRE CONNECTION
RCA Jack Line Out:
Red (right) White (left)
CONNECTOR A
4. MEMORY +24V
5. AUTO ANTENNA OUTPUT
7. +24V (TO IGNITION KEY)
8. GROUND
Note: (connector A no. 7) must be connected by car ignition key in order to avoid that car battery being
drained when the car will be not used for long period.
CONNECTOR B
1. REAR RIGHT SPEAKER (+)
2. REAR RIGHT SPEAKER (-)
3. FRONT RIGHT SPEAKER (+)
4. FRONT RIGHT SPEAKER (-)
5. FRONT LEFT SPEAKER (+)
6. FRONT LEFT SPEAKER (-)
7. REAR LEFT SPEAKER (+)
8. REAR LEFT SPEAKER (-)
Maintenance
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after the
replacement, there may be an internal malfunction. In this case, consult your nearest repair center.
Warning
Use the specified fuse amperes for each lead. Use of a higher fuse amperes may cause serious damage.
Dashboard
GREY +
GREY/BLACK –
FRONT
RIGH T
SPEAKER
VIOLET +
VIOLET/BLACK –
REAR
RIGH T
SPEAKER
FRONT
LEFT
SPEAKE R
REAR
LEF T
SPEAKE R
+ WHITE
– WHITE/BLACK
+ GREEN
– GREEN/BLACK
ISO A/B PLUG
POWE R
ANTENNA
BLU E
IGNITION SWITCH (B+)
RED
MEMOR Y
YELLOW
BACK UP
BLACK
GROUND (– )
LINE OUT
L (WHITE) R (RED)
ANTENNA
CONNECTOR
ISO CONNECTOR
B
A
FUSE 5A
8642
7531
8
4
75
GREY +
GREY/BLACK –
FRONT
RIGH T
SPEAKER
VIOLET +
VIOLET/BLACK –
REAR
RIGH T
SPEAKER
FRONT
LEFT
SPEAKE R
REAR
LEF T
SPEAKE R
+ WHITE
– WHITE/BLACK
+ GREEN
– GREEN/BLACK
ISO A/B PLUG
POWE R
ANTENNA
BLU E
IGNITION SWITCH (B+)
RED
MEMOR Y
YELLOW
BACK UP
BLACK
GROUND (– )
LINE OUT
L (WHITE) R (RED)
ANTENNA
CONNECTOR
ISO CONNECTOR
B
A
FUSE 5A
8642
7531
8
4
75

EN-3
10
1
2
3
4
4
5
6
8
7
4
5
6
9
1. UNIT
2. RELEASE CASE
3. DASH
4. HEX NUT
5. LOCK WASHER
6. PLAIN WASHER
7. CAR BODY
8. REAR SUPPORT STRAP
9. TAPPING SCREW
10. M5 X 15 HEX BOLT
TO SUPPORT THE UNIT
WIRE CONNECTION
RCA Jack Line Out:
Red (right) White (left)
CONNECTOR A
4. MEMORY +24V
5. AUTO ANTENNA OUTPUT
7. +24V (TO IGNITION KEY)
8. GROUND
Note: (connector A no. 7) must be connected by car ignition key in order to avoid that car battery being
drained when the car will be not used for long period.
CONNECTOR B
1. REAR RIGHT SPEAKER (+)
2. REAR RIGHT SPEAKER (-)
3. FRONT RIGHT SPEAKER (+)
4. FRONT RIGHT SPEAKER (-)
5. FRONT LEFT SPEAKER (+)
6. FRONT LEFT SPEAKER (-)
7. REAR LEFT SPEAKER (+)
8. REAR LEFT SPEAKER (-)
Maintenance
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after the
replacement, there may be an internal malfunction. In this case, consult your nearest repair center.
Warning
Use the specied fuse amperes for each lead. Use of a higher fuse amperes may cause serious damage.
Dashboard
GREY +
GREY/BLACK –
FRONT
RIGHT
SPEAKER
VIOLET +
VIOLET/BLACK –
REAR
RIGHT
SPEAKER
FRONT
LEFT
SPEAKER
REAR
LEFT
SPEAKER
+ WHITE
– WHITE/BLACK
+ GREEN
– GREEN/BLACK
ISO A/B PLUG
POWER
ANTENNA
BLUE
IGNITION SWITCH (B+)
RED
MEMORY YELLOW
BACK UP
BLACK
GROUND (–)
LINE OUT
L (WHITE) R (RED)
ANTENNA
CONNECTOR
ISO CONNECTOR
B
A
FUSE 5A
8642
7531
8
4
75
GREY +
GREY/BLACK –
FRONT
RIGHT
SPEAKER
VIOLET +
VIOLET/BLACK –
REAR
RIGHT
SPEAKER
FRONT
LEFT
SPEAKER
REAR
LEFT
SPEAKER
+ WHITE
– WHITE/BLACK
+ GREEN
– GREEN/BLACK
ISO A/B PLUG
POWER
ANTENNA
BLUE
IGNITION SWITCH (B+)
RED
MEMORY YELLOW
BACK UP
BLACK
GROUND (–)
LINE OUT
L (WHITE) R (RED)
ANTENNA
CONNECTOR
ISO CONNECTOR
B
A
FUSE 5A
8642
7531
8
4
75

EN-4
1. POWER ON/OFF ( ) / MUTE ( )
2. FUNCTION SELECT BUTTON:BASS/TREBLE/BALANCE/FADER /
I-VOL/ADJUST CLOCK/DISP/STEREO/LOC/EQ
3. VOL UP/VOL DOWN FOR BASS/TREBLE/BALANCE/FADER
4. PRESET STATIONS (1,2,3,4,5,6)
5. MODE BUTTON (MD)
6. BAND/LOUDNESS BUTTON (BD/LD)
7. AUTOMATIC OR MANUAL TUNING (FREQ UP OR FREQ DOWN ) /
TRACK/SEARCH BUTTON
8. AUTO SEEK SEARCH TUNING (AS/PS)
9. LCD DISPLAY
10. OPEN PANEL BUTTON ( )
11. PAUSE BUTTON
12. REPEAT BUTTON
13. INTRO BUTTON (Preview all Tracks)
14. RANDOM BUTTON
15. PREVIOUS/NEXT FOLDER SELECT: (In case of MP3/WMA les)
16. USB PORT
17. MULTI-MEDIA CARD (MMC) / SD CARD SLOT
18. AUX IN
LOCATIONS OF PARTS
AS/PS
MD
BD/LD
AUX
3
INT
6
FL+
2
RPT
1
PAU
4
RDM
5
FL-
9141162 31 5 7 10 17
1513812 18 16
(1-6)
4
AS/PS
MD
BD/LD
AUX
3
INT
6
FL+
2
RPT
1
PAU
4
RDM
5
FL-

EN-5
OPERATING INSTRUCTIONS
1. POWER ON/OFF
Press any key to power the unit. Press and hold to turn off.
MUTE
If you just press this button briey, it will turn to MUTE. To return to sound, press it briey again.
2. FUNCTION SELECT BUTTON:BASS/TREBLE/BALANCE/FADER /
I-VOL/ADJUST CLOCK/DISP/STEREO/LOC/EQ
3. VOLUME UP/DOWN
Turing the VOL knob to right or left (3) to control the VOLUME. To select other functions, hold the VOL knob
down until the desired functions is shown on the display. Figure 1 shows how control functions are selected
using the VOL knob.
1 2 3 4 5
SEL SEL SEL SEL SEL
Fig. 1 Selection of sound control functions
1. VOLUME 2. BASS 3. TREBLE 4. BALANCE 5. FADER
These buttons can be used to adjust the BASS, TREBLE, BALANCE and FADER.
Press and hold VOL knob to adjust below function:
I-VOL
SEL
2 sec.
SEL ADJ CLOCK SEL DISP SEL STEREO SEL LOC OFF SEL EQ OFF
I-VOL
Turn the VOL knob to set the volume level, with which the device is to be set when turned on.
ADJUST CLOCK
Turn VOL knob to right for hours and turn VOL knob to left for minutes.
DISPLAY
Time show on display
STEREO/MONO
When FM signal is weak or distorted, reception may improve by turn VOL knob to select MONO.
LOCAL
“Local” position in areas with strong signal will cause radio to stop at only strong stations. During manual
tuning (LOC appears). Select Distant position in areas with weak signal. Turn the “VOL” knob to set the
LOCAL ON/OFF.
EQ MODE
Turn VOL knob to select one of the settings EQ OFF/CLASS/ROCK/POP/EQ FLAT.
4. PRESET STATIONS (1,2,3,4,5,6)
(A) RADIO MODE:
Six numbered preset buttons store and recall stations for each band.
Storing a station:
1. Select a band (if needed)
2. Select a station
3. Hold a preset button longer than one second. Preset numbers appear in the display when station is saved.
Recall a station:
1. Select band (if needed)
2. Press a preset button for less than one second to select stored station.
(B) MP3 PLAYER MODE:
1. PAUSE 2. REPEAT 3. INTRO 4. RANDOM
5. MODE BUTTON (MD)
Press this key, to select AUX/TUNER/USB or MMC/SD mode..
6. BAND SELECTOR / LOUDNESS BUTTON (BD/LD)
Press this button to toggle through the preset Radio FM1(OIRT)---FM2---FM3---AM1---AM2.
LOUDNESS: Press and hold the button to select LOUDNESS mode.

EN-6
7. AUTOMATIC OR MANUAL TUNING (FREQ UP OR FREQ DOWN )
(A) RADIO MODE
When pressed for less than 1 second, the unit operates in automatic tuning mode.
When pressed longer than 1 second, the unit operates in manual tuning mode.
If the keys are not pressed again within 3 seconds, the unit will return to SEEK mode.
(B) MP3/WMA PLAYER MODE
When pressed for less than 1 second, they will operate as TRACK UP or TRACK DOWN mode.
When pressed longer than 1 second, they will operate as CUE or REVIEW mode.
8. AUTOMATICALLY STORE STATIONS (AS/PS)
Select six strong stations and store them in current band.
1. Select a band (if needed)
2. Hold AS/PS button for more than three seconds. The new stations replace those already stored in that
band.
Preset Scan
To scan stations stored in current band.
1. Select a band (if needed)
2. Press AS/PS for more than one second but less than three. The radio pauses for ve seconds at each
statio. Press AS/PS again to stop scanning when desired station is found.
9. LCD DISPLAY
The Liquid Crystal Display will show the current settings of the unit.
10. OPEN THE FRONT PANEL
Press button and the front panel will open.
MP3/WMA CONTROL LOCATION OF PARTS
11. PAUSE BUTTON
During “PLAY”, press (11) ‘PAU’ button to “PAUSE”. Press gain to resume play.
TRACK/SEARCH BUTTON (7)
FORWARD AND REVERSE TRACK SEARCH (or changing songs)
Press and release to advance to next track or to return to the beginning of the current track (track number will
be displayed.) Press and hold to or . Play will begin at the point where you release the button.
12. REPEAT BUTTON ‘RPT’
When this button is pressed, ‘RPT’ is displayed and the selected track will play continually. Press again to
listen to all tracks.
13. INTRO BUTTON (Preview all Tracks)
When this button is pressed, ‘INT’ is displayed and the rst few seconds of each track on the disc play.
Press again to stop ‘intro’ and listen to track.
14. RANDOM BUTTON ‘RDM’
When this button is pressed, ‘RDM’ is displayed and each track is played in random instead of normal
sequence. To cancel RANDOM mode, press ‘RDM’ button again.
15. PREVIOUS/NEXT FOLDER SELECT: (In case of MP3/WMA les)
M5: Previous Folder / M6: Next Folder
HOW TO SELECT MP3/WMA FILES
Note: During playback the information from the ID3 tag of the MP3 les are read and are shown successively
in the display.
Press briey BD/LD button to turn ON or OFF the ID3 tag.
MP3/WMA music function:
Note: In all operation, use “SEL” button to choose the BAS, TRE, BAL FAD, and VOL functions, respectively.
• Press and hold “AS/PS”.
Folder Select: (Music paused in operation)
• Press and hold “AS/PS” to activate the Folder search. Then turn the Volume knob to select the folder, and
press the “SEL” button to enter the folder.
• Press / button to select the desired folder. The song will automatically play.

EN-7
Song Number Select: (Select in current folder)
• Press “AS/PS” for the 2nd time to activate the Song Number search.
• Press / button to select the desired track. The song will automatically play.
Folder Number Select: (eg. Dir 1, 2,.... etc)
• Press “AS/PS” for the 3rd time to activate the Folder Number search.
• Press / button to select the desired Folder number. The song will automatically play.
Song Name Select: (Music paused in operation)
• Press “AS/PS” for the 4th time to activate the Song Number search.
• Press / button to select the desired Song number. The song will automatically play.
Connecting it to Portable MP3 Player
16,17. USB/ SD/MMC MEMORY CARD
The device is equipped with a USB interface and a memory card reader for SD/MMC cards. MP3 or WMA
les stored on these media can be played.
1. Plug your USB storage medium into the USB port.
2. If you use a memory card, insert it into the memory card reader.
3. The player automatically switches to the input used and starts playback.
4. See the section on operations common for audio les on how to control USB or memory card playback.
Note:
• Due to the great variety of devices with USB and SD/MMC card interfaces that sometimes have manu-
facturer-specic functions, we cannot guarantee that all media will be recognized and that all operational
functions will be available with this device.
• You cannot operate USB hard drives on the device.
18. FRONT AUX IN
An external audio source (e.g. portable MP3 player) can be connected to the AUX IN socket to be played
back by the vehicle loudspeakers. Press the MD button to select the AUX IN mode.
• Connect the AUX IN socket with the audio output of the external device.
MEMORY BACKUP
This unit is equipped with built-in memory I.C. (Integrated Circuits) to save user settings such as tuner preset
stations and audio control settings. Whenever power is unplug, these settings will not be lost.

EN-8
CAUTION & MAINTENANCE
This detachable panel AM/FM car radio with MP3/WMA player is an example of superior design and craftsmanship.
The following suggestions will help you care for the product and experience many years of enjoyment.
1. Do not touch the contacts on the front panel or the unit body.
2. The product can only operate on 10.8V-32V DC power supply, negative ground.
3. Avoid exposing your product to high temperature and humidity.
4. Handle the product with care. Dropping it can damage circuit boards and cause the product to malfunction.
5. Modifying or tampering with internal components can cause damage and may invalidate the warranty.
TROUBLESHOOTING GUIDE
Check to see that all the power and
speaker leads are securely connected.
Check balance control.
Reverse left and right channel speaker leads If no
sound from other side, check or replace speaker
wire. If no sound from both sides, replace both
speakers.
Replace with a good sensitivity antenna.
Recommend used 8 ohm or equivalent speaker
impedance.
No sound or power
No sound in one
channel
Poor FM reception
Sound distortion &
unstable
Speaker cord disconnected.
Bad power connection
Blown fuse.
Mis-adjusted balance
control
Damaged speaker wire or speaker
Insensitive or defective antenna.
Used speaker 4 Ohm impedance
or lower, Cause power amplifier
over heat.
SYMPTOM POSSIBLE CAUSE SOLUTION
Replace fuse with same amperage.
TECHNICAL SPECIFICA TIONS
MP3/WMA PLAYER SECTION
Signal to noise ratio > 60 dB
Channel separation > 50 dB (1kHz)
Frequency response 60Hz - 15 kHz
TUNER (FM)
Frequency range 65-74 MHz
Channel step 30 kHz
Frequency range 87.5-108 MHz
Channel step 50 kHz
Sensitivity 4 µV
Stereo separation 30 dB
Signal to noise ratio 50 dB
TUNER (AM)
Frequency range 522-1620 KHz
Usable sensitivity
LINE-OUT
Output 5V (max.)
Impedance 10k Ohm
GENERAL
Power supply 24V DC (10.8-32V allowable)
Speaker impedance 4 or 8 ohm
Output power 4 x 18 Watts
Fuse 5A
Note: Specifications and design may be subject to change without prior notice
50 µV