Vertical Technik AG03 User manual

Distribution and Maintenance Vertical Technik AG,
Bächliackerweg 6, CH-4402 Frenkendorf, Tel. [phone] www.verticalskate.ch
1
Rope Challenge
AG03
Product Manual

Distribution and Maintenance Vertical Technik AG,
Bächliackerweg 6, CH-4402 Frenkendorf, Tel. [phone] www.verticalskate.ch
2
Instructions for Use:
By trying to stand on this equipment, it improves ones’ alance.
General Information:
Length: 2114 mm
Width: 150 mm
Height: 545 mm
Weight: 145 KGS
Required Safety Zone: 3104 mm - 5104 mm
Maximum User Weight: 60 KGS
Num er of Users: 1 Persons
Activities: Balance.

Distribution and Maintenance Vertical Technik AG,
Bächliackerweg 6, CH-4402 Frenkendorf, Tel. [phone] www.verticalskate.ch
3
Safety Zones:
Safety zones of all products are given in the following pages. Please note that the products should
e assem led in such a manner that safety zones of the products should not intersect. The
illustrations given elow try to explain this point.

Distribution and Maintenance Vertical Technik AG,
Bächliackerweg 6, CH-4402 Frenkendorf, Tel. [phone] www.verticalskate.ch
4
Safety Zone for AG 03 Rope Challenge:

Distribution and Maintenance Vertical Technik AG,
Bächliackerweg 6, CH-4402 Frenkendorf, Tel. [phone] www.verticalskate.ch
5
Maintenance Plan:
The following maintenance plan is according to DIN 79000. According to DIN 79000, it is the duty
of the customer to comply with the following plan and document all inspections. The person
performing the inspection should e competent to do so. Any failure may result in the product
not eing according to DIN 79000 and may void warranties. Also adhering to the maintenance
plan will make your products last longer. Please contact us in case you need any assistance.
The inspection is divided into three parts depending on the frequency of the inspection; weekly
routine, monthly operational and annual inspection. The frequency of the inspections should e
increased in areas where there is more frequent use, where there is more vandalism and areas
that are close to the sea. For example it may e a good idea to do a daily inspection instead of a
weekly inspection in a heavily used area such as a school.
To prevent any accidents and damages, defects that are detected should e repaired
immediately. It may e a good idea to close the product to pu lic use efore necessary repairs
are done. Please contact Flopark for any help or any spare parts requirements.
Weekly routine inspection:
•Check for o vious signs of damage, such as roken parts, missing parts, sharp edges.
•Check for loose olts.
•Make sure the foundation is not exposed.
•Check moving parts to make sure they are in good condition and that the movementis
smooth.
•Check for o vious signs of damage, such as roken parts, missing parts, sharp edges.
•Check safety surfacing to ensure that it is not damaged.
•Check for any dents or scratches and use touch up paint to cover them. This is toprevent
rusting.
•Check the safety zone around the products to make sure that it is free from any other
o jects and that the surface is clean and free from de ris, roken glass etc.
•Check the product markings. If removed, or if they cannot e read, ask for replacements.
Monthly operational inspection:
•Repeat the steps for the weekly routine inspection.
•Repeat all the moves in the products. Make sure the torsion system works properly.
•Check for any excessive wear. Check all fixations.
•Check for any signs of corrosion.
•Check all olts to see if any are loose. Retighten if necessary.
•Make sure all seats, grips, foot pedals etc. are secure.
•If necessary grease earings.

Distribution and Maintenance Vertical Technik AG,
Bächliackerweg 6, CH-4402 Frenkendorf, Tel. [phone] www.verticalskate.ch
6
Annual Inspection:
•Perform monthly operational inspection.
•Make sure the products are fixed to the foundations. It may e a good idea to remove the
post covers and retighten the olts that fix the structure to the foundation.
•Check the central post for any wear. Check all welds.