GSWeb Playground Equipment NET JUMPER GS-W5001 User manual

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 1
INSTALLATION MANUAL
GSWeb Playground Equipment
1046-3, Najeon-ri, Saengnim-myeon,
Gimhae-si Gyeongsangnam-do,
621-821, Republic Of Korea
Tel) +82. 55. 326. 9096~7
Fax) +82. 55. 326. 9022
E-mail) [e-mail]
Web site) www.gsweb21.com
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 2
INSTALLATION & MAINTENANCE INSTRUCTIONS
Ages: 2 to 5 years
Capacity: 13 children
Size: D: 18' 4" / 5.60m
H: 3' 11" / 1. 20m
Use zone
D: 28' 3" / 8.60m
Figure-1: Completed Net
Features
The series is a specialty climbing structure featuring
a flexible center area surrounded by netting. It is made of
steel-loaded Nylon cables with UV guard and the landing
surface is a textile-reinforced flexible rubber material.
The GS-W5001 features GS Web technology which includes
the highest steel content and the strongest connection materials
in the industry, including a steel-wire core in our edge ropes
and connection points crushed in place with over 75 tons
of preasure to ensure long life of the games and maximum
safety for the children.
GS Web Nets help bring movement, balance,
exercise and fun back into the playground.
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 3
Safety area and Fall Height zone
Figure-2: Install and safety area
Metric/Imperial
conversion:
2600mm = 8' 6-1/4"
4200mm = 13' 9-1/4"
9260mm = 30' 4-1/2"
Safety area
The requirements for space and safety clearances are taken from
BS-EN 1176-1/ ASTM-F1487/ CSA Z614
The use zone for stationary play equipment shall extend no less than
72 in.(1830mm) from all sides of the play structure.
Fall Height :1200mm (from surface)
The Fall height on the extennal surface of a pyramid shaped space net
is the highest point attainable on the edge of the structure where an unimpeded fall to
the protective surface is possible. This height is based on the centre of gravity height
of the maximum user.
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 4
Foundation Information
Level Line
P1
P2
Wet concrete
Dry concrete
surface layer
Finished ground
Pole
P1 = Depth below finished Grade (12" / 300mm)
P2 = Depth of concrete footing (19-2/3" / 500mm)
Figure-3: Foundation section view
Foundation
Please refer to GS-W5001 drawing for exact installation dimensions
Figure-4: Excavate enough
materials to allow for proper depth
of concrete footings
Also ensure that there is enough space to
allow the frame to be positioned properly.
Anchor wood support frame to ground
with pickets to prevent the frame from
moving while concrete is poured and sets.
Finished Grade
(Optional)
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 5
Foundation Layout
Positioning Anchor plate on footing
[CF] 'L" anchor hole
Front edge of anchor plate must be
installed
4" / 100mm from edge of concrete footing.
Figure-5: Concrete footing and Anchor plate Layout
Note: Total distance from
front of block to front of
block is 7' 10" (2400mm)
Metric/Imperial conversion:
100mm = 4" 550mm = 1' 9-5/8"
250mm = 9-7/8" 600mm = 1' 11-1/2"
500mm = 1' 7-5/8" 1600mm = 5' 3"
Metric/Imperial
conversion:
1200mm = 3' 11-1/4"
2400mm = 7' 10-1/2"
2800mm = 9' 2-1/4"
5600mm = 18' 4-1/2"
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 6
Concrete Foundation
NOTE: Use anchor plate(post plate)
as guide for exact measurements.
Remove wood support frame from dry concrete blocks
After concrete has cured enough, remove frame and replace soil in area
around footing to subgrade level
Figure-6: Concrete footing
Metric/Imperial
conversion:
1200mm = 3' 11-1/4"
2400mm = 7' 10-1/2"
2800mm = 9' 2-1/4"
5600mm = 18' 4-1/2"
Metric/Imperial conversion:
25mm / 30mm = 1" 200mm = 7-7/8"
100mm = 4" 250mm = 9-7/8"
150mm = 6" 600mm = 1' 11-1/2"
190mm = 7-1/2"
Assemble wooden support frames *
6 frames (5' 3" / 1600mm L x 1' 8" / 500mm W x 1' 8" / 500mm H)
*Use ½" (min) plywood; not included in package
Concrete
Pour concrete* into wooden support frame until flush to top edge.
Allow 3-5 days for concrete to cure before proceeding to next step.
*Concrete is to be wet concrete with minimum 25 MPa / 3500 PSI.
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 7
Post Plate and Anchor Plate Assembly
Figure-7: Attach Anchor plate to footing
with flat washer, locking washer and nut.
Plate Assembly
Concrete block-clean threads of "L" anchor bolts.
Attach Anchor plate to footing
Metric/Imperial conversion:
350mm = 1' 1-3/4"
550mm = 1' 9-5/8"
700mm = 2' 3-1/2"
1300mm = 4' 3-1/4"
1550mm = 5' 1"
2100mm = 6' 10-3/4"
2700mm = 8' 10-1/4"
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment
M22 X L110 H/T BOLT
STEP-1
Post Plate STEP-2
8
Main rope Assembly
Figure-8: Attach Turnbuckle and rope
Main rope joint
Step 1: Attach top rope with
M22 X L110 H/T BOLT as shown in Figure 9
Step 2: Attach Turnbuckle to anchor plate
with M22 X L110 H/T BOLT.
Loosen Turnbuckle all the way (about 100mm),
leaving only 4 or 5 threads attached
Anchor Plate
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 9
Post Assembly
Note: Rubber mallet
may be required to
insert cap into post.
STEP-4
M22 X L70 T/S BOLT
Figure-9: Post cap assembly.
Figure-10: Post assembly.
STEP-3
A
B
C
ABCA
Post assembly
Step 3: Attach Post Cap to Post (Figure 10)
Step 4: Attach Post to Post base with
M22 X L70 T/S BOLT (Figure 11)
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 10
Attaching Turnbuckle to Anchor Plates
It is strongly recommended
that 3-4 workers lift the net into place.
Figure-11: Tightening Turnbuckles
(a)
(b)
Tighten Rope with Turnbuckles at the Same time
Tighten Rope with Turnbuckles at the Same time
(a) + (a)
(c) + (c)
NOTE: Make sure post is level before tightening and remains level during process.
(b)
(c)
(c)
Tighten Rope with Turnbuckles at the Same time
(b) + (b)
(a)
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 11
Figure-12: completed Net
Maintenance information
Please tighten rope with Turnbuckle properly.
If you tighten the net too much, it may damage the net.
It is also recommended that subsequent checks on tension
be carried out at monthly intervals and adjusted as required.
This will increase the overall longevity of the product.
Checking: 1 month
Refer to IPEMA and TUV maintance system.
After properly tensioning the net, it will
stretch slightly over the first four weeks of use.
Following this initial period, the net needs
to be fully re-tensioned by Turnbuckle after 1 year.
Tensioning & Maintenance information
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 12
PARTS LIST
1: main post
2: multi compound rope
3: post cap
4: turn buckle
5: anchor shackle
6: T/S bolt,nut, washer
7: H/T bolt,nut, washer
8: post plate
9: L-anchor bolt,nut,washer
10: Anchor plate
1
2
10
6
7
9
4
5
8
3
9-1
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 13
Maintenance Installation
A weekly check of the activity net is recommended to ensure
that no acts of vandalism have damaged the rope.
Periodic checks on tension will assist in the durability of the product.
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 14
Maintenance
A. General safety measures
On the playground there should be a sign(pictogram) giving the following information:
a) general emergency telephone number;
b) telephone number to contact maintenance personnel;
c) name of the playground;
d) address of playground; and
e) other relevant local information, if applicable.
The entry, exit and emergency paths to and from a playground, intended for use by the public and emergency services, should be accessible and
free of obstacles at all times.
NOTE Attention is drawn to local regulations.
B. Procedures
Defects that occur during operation and which put safety at risk should be corrected without delay. If this is not possible, the equipment should
be secured against use e.g. by immobilization or removal.
There should be written operational procedures covering the measures to be taken in the event of accidents, fire and the like.
Until unsafe equipment is repaired and released for use, access by the public should be prevented. Information about accidents brought to the
attention of the manager should be recorded on a form that includes the following details:
a) date and tie of accident;
b) age and sex of victim and clothing worn, Including footwear;
c) equipment involved;
d) number of children on site at the time of the accident;
e) description of accident;
f) injury sustained including part(s) of body affected;
g) action taken;
h) witness statements;
i) any subsequent equipment modification;
j) weather conditions; and
k) any other relevant information.
By Lappset Group Oy
200220/ 220220

NET JUMPER MODEL NO.
GS-W5001
GSWeb Playground Equipment 15
Maintenance
C. Routine maintenance
To reduce accidents, the owner or operator should ensure that an appropriate routine maintenance schedule is established, implemented and
maintained. This should take into account local conditions and the manufacturer's instructions that can affect the necessary inspection frequency.
The schedule should list the components to be maintained and should also give procedures for dealing with complaints and breakdowns.
The routine maintenance of playground equipment and surfaces should consist of preventative measures to maintain their level of safety,
performance and compliance with the relevant part(s) of EN 1176. Such measures should include:
a) tightening of fastenings;
b) re-painting and re-treatment of surfaces;
c) maintenance of any impact attenuating surfaces;
d) lubrication of bearings;
e) markig of equipment to signify loose fill finished surface level;
f) cleaning;
g) removal of broken glass and other debris or contaminants;
h) restoring loose fills to the correct level; and
i)maintenance of free space areas.
D. Corrective maintenance
Corrective maintenance should include measures to correct defects, or th re-establish the necessary levels of safety of the playground equipment
and surfaces. Such measures should include:
a) replacement of fastenings;
b) welding of welding repairs;
c) replacement of worn or defective parts; and
d) replacement of defective structural components.
E. Personal safety
Repairs during operation that could put the safety of maintenance personnel of the public at risk, should be avoided.
F. Equipment alterations
Alterations to parts of a piece of equipment or structure that could affect the essential safety of the equipment should only be carried out after
consultation with the manufacturer or a compete person.
By Lappset Group Oy
200220/ 220220

NET JUMPER
NET JUMPERNET JUMPER
NET JUMPER By Lappset Group Oy
By Lappset Group OyBy Lappset Group Oy
By Lappset Group Oy
200220 / 220220
200220 / 220220200220 / 220220
200220 / 220220
ASENNUSOHJE
ASENNUSOHJEASENNUSOHJE
ASENNUSOHJE
GSWeb Playground Equipment
1046-3, Najeon-ri, Saengnim-myeon,
Gimhae-si Gyeongsangnam-do,
621-821, Republic Of Korea
Puh: +82. 55. 326. 9096~7
Fax: [phone]
S-posti: [e-mail]
Nettisivu: www.gsweb21.com
GSWeb Playground Equipment 1
11
1

NET JUMPER
NET JUMPERNET JUMPER
NET JUMPER By Lappset Group Oy
By Lappset Group OyBy Lappset Group Oy
By Lappset Group Oy
200220 / 220220
200220 / 220220200220 / 220220
200220 / 220220
ASENNUS
ASENNUSASENNUS
ASENNUS-
--
- JA YLLÄPITO
JA YLLÄPITOJA YLLÄPITO
JA YLLÄPITO-
--
-OHJEET
OHJEETOHJEET
OHJEET
Ominaisuudet
Tämä sarja on erikoiskiipeilyrakennelma jossa on
joustava keskus jota ympäröi verkko. Se on valmistettu
nailon päällystettyllä teräsvaijerilla UV-suojauksella ja pohjan päällyste
on tekstiilillä vahvistettua joustavaa kumimateriaalia.
GS-W5001 käyttää GS Web teknologiaa joka sisältää
alan korkeimman teräspitoisuuden ja vahvimmat liitosmateriaalit,
mukaanlukien sivuköysien teräsvaijerisisuksen
ja liitoskohdat jotka ovat puristettu paikolleen 75 tonnin painetta
käyttäen varmistaen leikkien pitkän käyttöiän ja
maksimi turvallisuuden lapsille.
GS Web Nets tuovat liikettä, tasapainoa,
GSWeb Playground Equipment 2
22
2
Ikä: 2 - 5 vuotiaat
Kapasiteetti: 13 lasta
Koko: S: 18' 4" / 5,60m
K: 3' 11" / 1,20m
Käyttöalue:
S: 28' 3" / 8,60m
Kuva 1. Valmis verkko
GS Web Nets tuovat liikettä, tasapainoa,
liikunnan ja hauskanpidon takaisin leikkikentille.

NET JUMPER
NET JUMPERNET JUMPER
NET JUMPER By Lappset Group Oy
By Lappset Group OyBy Lappset Group Oy
By Lappset Group Oy
200220 / 220220
200220 / 220220200220 / 220220
200220 / 220220
Turva
TurvaTurva
Turva-
--
-alue ja putouskorkeusalue
alue ja putouskorkeusaluealue ja putouskorkeusalue
alue ja putouskorkeusalue
Kuva 2: Asennus- ja turva-alue
Metrinen/imperiaalinen
vaihdos:
2600mm = 8' 6-1/4"
4200mm = 13' 9
-
1/4"
Turva-alue
Tila- ja turvavapaatila-alue vaatimukset on otettu
BS-EN 1176-1/ ASTM-F1487/ CSA Z614 standardeista.
Liikkumattoman leikkivälineen käyttöalue saa ulottua ainakin
72” (1830mm) leikkivälineen kaikilta puolilta.
Putouskorkeus :1200mm (pinnasta)
Pyramidin muotoisessa verkossa putouskorkeus ulkoisesta pinnasta
on korkein mahdollinen piste rakennelman reunasta jossa vapaa pudotus
suojapintaan on mahdollinen. Tämä korkeus perustuu painopistekorkeuteen
maksimikäyttäjältä.
GSWeb Playground Equipment 3
33
3
4200mm = 13' 9
-
1/4"
9260mm = 30' 4-1/2"

NET JUMPER
NET JUMPERNET JUMPER
NET JUMPER By Lappset Group Oy
By Lappset Group OyBy Lappset Group Oy
By Lappset Group Oy
200220 / 220220
200220 / 220220200220 / 220220
200220 / 220220
Perustuksen t edot
Perustuksen t edotPerustuksen t edot
Perustuksen t edot
Level Line
P1
surface layer
Finished ground
Pole
Kuva 3: Perustuksen läpileikkaus
Perustus
Katso GS-W5001 piirustus saadaksesi tarkat asennuskoot
Viimeistelty taso
GSWeb Playground Equipment 4
44
4
P2
Wet concrete
Dry concrete
P1 = Syvyys mitoitettu viimeistellystä tasosta (300mm)
P2 = Betonianturan syvyys (500mm)
Kuva 4: Kaiva tarpeeksi jotta
saavutetaan riittävä upotussyvyys
betonianturoille
Varmista myös että on riittävästi tilaa
jotta teline voidaan sijoittaa
asianmukaisesti.
Kiinnitä puutukikehys maahan paaluja
käyttäen välttääksesi kehyksen
liikkumisen sinä aikana kun betoni
valutetaan ja kovettuu.
(Vaihtoehtoinen)

NET JUMPER
NET JUMPERNET JUMPER
NET JUMPER By Lappset Group Oy
By Lappset Group OyBy Lappset Group Oy
By Lappset Group Oy
200220 / 220220
200220 / 220220200220 / 220220
200220 / 220220
Perustuksen kaava
Perustuksen kaavaPerustuksen kaava
Perustuksen kaava
Ankkurilevyn asemointi jalustaan
[CF] 'L" ankkurin aukko
Ankkurilevyn etureuna täytyy asentaa
4” / 100mm betonijalustuksen reunasta.
Huom! Etäisyys
kappaleen etupuolelta
seuraavan kappaleen
etupuoleen
on 7’ 10” (2400mm).
Metrinen/imperiaalinen
vaihdos:
1200mm = 3' 11-1/4"
2400mm = 7' 10-1/2"
2800mm = 9' 2-1/4"
5600mm = 18' 4-1/2"
GSWeb Playground Equipment 5
55
5
Kuva 5: Betonijalus- ja ankkurilevykaavio
Metrinen/imperiaalinen vaihdos:
100mm = 4" 550mm = 1' 9-5/8"
250mm = 9-7/8" 600mm = 1' 11-1/2"
500mm = 1' 7-5/8" 1600mm = 5' 3"