Vestil PEL-Series User manual

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 1 of 17
PEL-Series Pallet Handlers
Instruction Manual
Receiving instructions:
After delivery, IMMEDIATELY remove the packaging from the product in a manner that preserves the packaging and
maintains the orientation of the product in the packaging; then inspect the product closely to determine whether it
sustained damage during transport. If damage is discovered during the inspection, immediately record a
complete description of the damage on the bill of lading. If the product is undamaged, discard the packaging.
Notes:
1) Compliance with laws, regulations, codes, and mandatory standards enforced in the location where the product is
used is exclusively the responsibility of the end-user.
2) VESTIL is not liable for any injury or property damage that occurs as a consequence of failing to apply either:
a) Instructions in this manual; or b) information provided on product labels.
Vestil Manufacturing Corp.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: [phone] -or-Toll Free [phone]
Fax: [phone]
Web: www.vestilmfg.com e-mail: [e-mail]
Table of Contents:
Signal Words……………………………………………..……………………………………………………………..………….. 2
Safe Use Recommendations……………..……………………………………………..…………………………..…….………2
Specifications…………………………………..…………………………………………………………..………………………. 3
FIG. 1: PEL-88 & PEL-100 exploded parts diagram & bill of materials…………..……………………………..………... 4, 5
FIG. 2: PEL-88-A & PEL-100-A exploded parts diagram & bill of materials………………………………………………… 6
FIG. 3: PEL-400-57 & PEL-400-72 exploded parts diagram & bill of materials………...………………….……………..7, 8
FIG. 4: PEL-100-A-SWA exploded parts diagram and bill of materials……………………………………………………… 9
Accessory carriage attachments…………………………………………………………………………………………………10
Installing accessory carriage attachments……………………………………………………………………………………... 10
FIG. 5: Electrical circuit diagram………………………………………………………………………………………………… 11
Operation Instructions……………………………………………………………………………………………………………. 12
Chain tension adjustment procedure (PEL-88 & PEL-100)………………………………………………..………………… 12
Chain tension adjustment procedure (PEL-400-57 & PEL-400-72)…………………………………………………………. 13
Battery Charger Operation………………………………………………………………………………………………………. 14
Inspections & Maintenance……………………………………………………………………………………………………… 15
Labeling Diagram…………….....…………………………………………………………………………………………………16
Limited Warranty…...…………………………………………………………………………………………………………..….17
Aluminum models
(PEL-88-A & PEL-100-A)
Steel models
(PEL-88, PEL-100, & PEL-400)

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 2 of 17
Signal Words:
This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable seriousness of
those injuries, if the product is misused in the ways described. Other signal words call attention to uses of the product likely
cause property damage. Each signal word used in this manual is defined below.
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS
INJURY.
Identifies actions likely to result in product/property damage, such as operation that might damage
the product.
Safe Use Recommendations:
Vestil strives to identify foreseeable hazards associated with the use of its products. However, material handling is
dangerous and no manual can address every conceivable risk. The end-user ultimately is responsible for exercising sound
judgment at all times.
If this product is used or maintained improperly serious personal injuries or death might result. ALWAYS
use the product properly.
•Failure to read and understand the entire manual before assembling, using or servicing the product
constitutes misuse.
•Read the manual to refresh your understanding of proper use and maintenance procedures whenever necessary.
•DO NOT attempt to resolve any issue with the product unless you are certain that it will be safe to use afterwards.
•DO NOT modify the product in any way. Unauthorized modifications might make the lifter unsafe to use and
automatically void the Limited Warranty (see p. 17).
•DO NOT exceed the capacity of your unit. Refer to the “Specifications” table on p. 3 as well as label 287 (see
“Labeling diagram” on p. 16) on the product for capacity information.
•Inspect the product according to the instructions on p. 15. Replace each part that is not in normal condition. DO NOT
use the product until it is fully restored to normal condition. ONLY use manufacturer-approved replacement parts.
•Cycle the deck all the way up and all the way down. Listen for unusual sounds as the deck rises and lowers. Watch
the deck for unusual movement.
•DO NOT use the lifter unless all machine guards are in place, i.e. the mast guard that conceals the chain(s).
•This product is NOT a personnel lift. DO NOT use it to lift or transport people.
•DO NOT walk or stand beneath the load deck at any time.
•DO NOT leave the lifter unattended when it is loaded. Lower the deck and unload it before leaving the lifter
unattended.
•ONLY transport loads with the deck no higher than necessary to support the load and avoid obstacles.
•DO NOT continue to push the “UP” button on the hand control if the forks do not respond. Remove the unit from
service and report the problem to maintenance personnel.
•Always lift pallets properly. Drive forward until the edge of a pallet contacts the heels of the forks.
•ONLY use this lifter on even, level ground.
•NEVER change the setting of the pressure relief valve.
•ALWAYS carefully watch the pallet handler and the load while lifting and transporting loads.
•DO NOT use this device UNLESS all labels (see “Labeling Diagram” on. p. 16) are in place, readable, and
undamaged.

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 3 of 17
Specifications:
Dimensions and other specifications appear in the diagrams and table below.
Model A B
Net
Weight
Capacity
PEL-88 655/16” 57” 172 lb. 175 lb.
PEL-100 805/16” 72” 179 lb. 125 lb.
Model A B
Net
Weight
Capacity
PEL-88A 57” 703/16” 144 lb. 175 lb.
PEL-100A 72” 853/16” 157 lb. 125 lb.
Model A B
Net
Weight
Capacity
PEL-400-57
671/4” 57” 373 lb. 400 lb.
PEL-400-72
821/4” 72” 392 lb. 400 lb.
PEL-400 -57 and PEL-400-72
PEL-88-A and PEL-100-A
PEL-88 and PEL-100

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 4 of 17
FIG. 1: PEL-88 and PEL-100 exploded parts diagram
NOTE: Bill of materials appears on following page

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 5 of 17
Item
Part no.
Description
Quantity
1
21-514-050
21-514-051
Subassembly, frame:
PEL-88
PEL-100
1
1
1.1
21-514-055
21-514-056
Weldment, frame:
PEL-88
PEL-100
1
1.2
21-042-020
Roller
4
1.3
21-113-027
Spacer, sleeve, rollers
4
1.4
21-516-003
Weldment, bracket, center rollers
1
1.5
16-132-164
Caster, front
2
1.6
16-132-163
Caster, rear
2
1.7
10896
HHCS tap bolt, 1/2” – 13UNC x 6”, fully threaded
1
1.8
36109
Hex nut, grade A, plain finish, 1/2” – 13UNC
3
1.9
33012
Flat washer, low carbon, zinc finish, 1/2”
1
1.10
11111
HHCS #2, zinc plated, 3/8” – 16 x 2”
3
1.11
37024
Nylon insert lock nut, grade 2, zinc finish, 3/8” – 16
5
1.12
11112
3/8” – 16 x 21/4” HHCS bolt
2
1.13
21-146-004
Spring, compression
1
1.14
33622
Split lock washer, carbon steel, medium zinc finish, 3/8”
4
1.15
36106
Hex nut, grade A, zinc plated, 3/8” – 16
4
1.16
33006
Flat washer, zinc plated, USS, 5/16”
1
2
21-139-001
Battery, 12V DC
2
3
21-641-005
Motor with gearbox, shaft and key stock
1
4
21-034-010
Accessory, electric, battery charger, 24V
1
5
15-016-068
Bracket, battery charger mount, formed
1
6
33004
Flat washer, USS, zinc plated, 1/4”
8
7
11003
Hex bolt, grade A, zinc plated, 1/4” – 20 x 3/4”
4
8
37018
Nylon lock nut, grade 2, zinc finish, 1/4” – 20
2
9
21-034-006
Circuit breaker, 15amp
1
10
21-156-006
Accessories, electrical, control box
1
11
21-034-025
Flanged inlet sleeve with locking ring
1
12
21-145-008
Specialty hardware, eyebolt
2
13
21-024-016
Cap, square ribbed inserts
2
14
99-034-013
Strap, battery box, with buckle
1
15
21-156-002
Control, touchpad, electronic
1
16
20-042-009
Sprocket drive
1
17
33618
Medium split lock washer, 1/4”
6
18
21-524-001
Weldment, cover, top sprocket
1
19
21-024-038
Handle, grip, flexible vinyl round cap
2
20
21-024-012
Cover, front, formed
1
21
21-024-014
Cover, back, right side, formed
1
22
21-024-013
Cover, back, left side, formed
1
23
31802
Screw, self-tapping
14
24
15-025-006
Grip, handle
2
25
31959
Hex washer head self-drilling screw
4
26
36102
Hex nut, grade A, zinc plated, 1/4” – 20
4
27
34308
Split shaft collar, low carbon steel, black oxide finish, 3/4”
1
28
21-042-012
21-042-013
#35 roller chain:
[PEL-88] x 337P w/2 CL
[PEL-100] x 417P w/2 CL
1
29
21-513-025
Subassembly, carriage with deck
1
29.1
21-538-035
Subassembly, carriage
1
29.1.1
21-538-034
Weldment, carriage
1
29.1.2
37021
Nylon insert lock nut, grade 2, zinc finish, 5/16” – 18
4
29.1.3
20-110-008
Bearing, roller
4
29.2
21-513-089
Subassembly, deck
1
29.2.1
21-513-024
Weldment, deck
1
29.2.2
21-013-057
Deck, top
1
29.2.3
24213
Flat head socket cap screw #10-32 x 1” long
4
29.2.4
37015
#10-32 Nylock nut, zinc plated
4
29.3
11107
Hex bolt, grade A, zinc finish, 3/8” – 16 x 11/4”
4
29.4
33008
Flat washer, low carbon, USS, zinc plated, 3/8”
8
29.5
33622
Split lock washer, carbon steel, medium zinc finish, 3/8”
4
29.6
36106
Hex nut, grade A, zinc plated, 3/8” – 16
4

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 6 of 17
FIG. 2: PEL-88-A and PEL-100A exploded parts diagram and bill of materials
Item
Part no.
Description
Qty.
Item
Part no.
Description
Qty.
1 42-514-002
42-511-003
Weldment, frame:
PEL-88A
PEL-100A
1
1
17 21-156-006 Accessory, electrical control box 1
2
42-525-001
Weldment, handle
1
18
21-024-042
Cover, motor
1
3 42-513-002 Weldment, deck 1 19 21-641-008
21-641-009
Screw drive:
PEL-88A: 645/8” length
PEL-100A: 75
3
/8” length
1
1
4
21-013-057
Deck, top
1
20
21-034-025
Flanged inlet sleeve with locking ring
1
5
42-538-001
Weldment, carriage
1 21
11012
Hex bolt, gr. A, zinc finish, 1/
4
”-
20x2
1
/4”
4
6
16-132-163
Caster with brake, PP-3/1.25-STM-
TTL
2 22
21-034-004
Circuit breaker
1
7
16-132-164
Caster, swivel, PP-3/1.25-STM
2
23
42-111-001
Bearing, sleeve
1
8
37024
Nylon insert lock nut, grade 2,zinc
finish,
3
/8”-16
4 24 42-024-002 Cover/guard, top cap 1
9
42-110-001
Bearing, roller
4
25
33618
Medium split lock washer, 1/4”
2
10
24213
Flat head socket cap screw #10-32x1”
6
26
33004
Flat washer, USS, zinc-plated, 1/4”
2
11
37015
10-32 lock nut, zinc plated
4
27
33006
Flat washer, USS, zinc plated, 5/16”
4
12
11105
Hex bolt, grade A, zinc plated, 3/
8
”- 16
x 1”
4 28
37018
Nylon lock nut, gr. 2, zinc finish 1/
4
” -
20
2
13
111003
Hex bolt, grade A, zinc plated, 1/
4
”-20 x
3
/4”
4 29
64137
Spring pin, AISI 1070-1095, pain
finish,
3/
16” x 1
1/
2”
1
14
21-156-002
Control, touchpad, electronic
1
30
21-024-038
Handle, grip, flexible vinyl round cap
2
15
21-139-001
Battery, 12VDC
2
31
15-025-006
Grip, handle
2
16
21-034-010
Accessory, battery charged, 24V
1
32
42-027-002
Brush seal, standard PP flex
2

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 7 of 17
FIG. 3: PEL-400-57 and PEL-400-72 exploded parts diagram
NOTE: Bill of materials appears on following page

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 8 of 17
Item
Part no.
Description
Quantity
1
21-002-059
21-002-060
Final assembly without power unit:
PEL-400-57
PEL-400-72
1
1
1.1
21-514-068
21-514-069
Frame, weldment:
PEL-400-57
PEL-400-72
1
1
1.2
21-516-009
Weldment, bracket, sprocket
1
1.3
10896
HHCS tap bolt 1/2” – 13UNC x 6” fully threaded
1
1.4
21-146-005
Spring, compression
1
1.5
33012
Flat washer, low carbon, zinc finish, 1/2”
1
1.6
36209
1/2” – 13 hex jam nut, plain
3
1.7
21-113-033
Spacer, 23/32” length
2
1.8
26356
SHSCS, 1/2” x 21/2” shoulder, 3/8” – 16 THD
2
1.9
37024
Nylon insert lock nut, grade 2, zinc finish 3/8” – 16
4
1.10
21-113-032
Spacer, 9/16” length
2
1.11
21-042-018
Sprocket, idler
6
1.12
26353
Socket head shoulder bolt, 1/2” x 13/4” with 1/4” hex, 3/8” – 16UNC threads
1
1.13
26358
3/8” – 16 SHSB, 1/2”x 3” shoulder
1
1.14
21-113-030
Spacer, 1/4” length
2
1.15
16-132-342
Stem caster, welded, rigid
2
1.16
16-132-156
4” stem caster with brake
2
1.17
21-024-024
Cover, left side, formed
1
1.18
21-024-023
Cover, right side, formed
1
1.19
37032
1/2” nylon insert jam nut
4
1.20
31802
Self-tapping screw
14
2
21-024-029
Guard, top, formed
1
3
15-025-006
Grip, handle
2
4
21-145-004
Bolt, chain, adjustment, 1/2” – 13 x 21/4”
4
5
36209
1/2” – 13 hex jam nut, plain
8
6
11055
Hex bolt, grade A, zinc plated, 5/16” – 18 x 1”
2
7
37021
Nylon insert lock nut, grade 2, zinc finish, 5/16” – 18
2
8
21-139-002
Battery, 12V DC
2
9
15-016-068
Bracket, battery charger mount, formed
1
10
33004
Flat washer, USS zinc plated, 1/4”
6
11
11003
Hex bolt, grade A, zinc plated, 1/4” – 20 x 3/4”
4
12
37018
Nylon lock nut, grade 2, zinc finish, 1/4” – 20
3
13
21-034-010
Accessory, electric battery charger, 24V
1
14
21-156-004
Control, motor, electronic, 1228
1
15
27402
RHSMS #8-32 x 1” long
2
16
01-022-001
Limit switch with roller arm
1
17
22804
Flat countersunk head elevator bolt, plain finish, 1/4” – 20 x 11/2”
1
18
21-641-002
Leeson motor/gearbox
1
19
21-156-002
Control, touchpad, electronic
1
20
21-034-025
Flanged inlet sleeve with locking ring
1
21
21-034-004
Circuit breaker
1
22
21-042-019
Gearbox sprocket
1
23
11107
Hex bolt, grade A, zinc finish, 3/8” – 16 x 11/4”
4
24
37024
Nylon insert lock nut, grade 2, zinc finish, 3/8” – 16
4
25
21-024-038
Handle, grip, flexible vinyl, round cap
2
26
99-034-013
Strap, battery box, with buckle
1
27
33618
Medium split lock washer, 1/4”
2
28
21-042-017
21-042-021
Chain:
PEL-400-57: #40-1R x 265 links
PEL-400-72: #40-1R x 325 links
2
2
29
21-513-036
Subassembly, carriage with deck
1
29.1
21-538-037
Subassembly, carriage
1
29.1.1
21-538-036
Weldment, carriage
1
29.1.2
21-112-008
Pin, rollers
4
29.1.3
21-527-003
Assembly, roller bearing
4
29.1.4
64135
Pin, roll pin, 3/16” x 11/4”
4
29.2
21-513-090
Subassembly, deck
1
29.2.1
21-513-035
Weldment, deck
1
29.2.2
21-013-064
Deck, top
1
29.2.3
24213
Flat head socket cap screw #10-32 x 1” long
4
29.2.4
37015
10-32 Nylock nut, zinc-plated
4
29.3
33008
Flat washer, low carbon, USS, zinc plated, 3/8”
8
29.4
11107
Hex bolt, grade A, zinc finish, 3/8” – 16 x 11/4”
4
29.5
33622
Split lock washer, carbon steel, medium zinc finish, 3/8”
4
29.6
36106
Hex nut, grade A, zinc plated, 3/8” – 16
4
30
21-037-020
Stop, rubber bumper
2
31
31807
Self-drilled screw, steel, zinc-plated, #8-18 x 11/4”
4
PEL-400-57 and PEL-400-72 bill of materials:

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 9 of 17
FIG. 4: PEl-100-A-SWA exploded parts diagram
NOTE: Bill of materials on following page
Detail A: Housing removed to show internal components
Item
Part no.
Description
Quantity
Item
Part no.
Description
Quantity
1 42-514-003
Weldment, frame (upright portion
referred to as the “Mast”)
1
15 16-132-155
Caster, swivel, stem, HR-4/1.25-SLB-
S
2
2 42-538-001 Weldment, carriage
1
16 16-132-156
Caster, swivel with brake, HR-4/1.25-
SLB-S
2
*3 20-110-008 Roller bearings
4
17 11109
3/
8
” – 16 x 11/
2
” HHCS #2 zinc-plated
bolt
4
4
11003
1/4” – 20 x 3/4” hex head bolt
4
18
16-132-009
Wheel, PP-4/1.25-W
4
5 11105 3/8” – 16 x 1in. hex head bolt
4
19 11109
3/
8
” – 16 x 4” HHCS#2 zinc-plated hex
head bolt
2
6
37024
3/4” lock nut
6
20
37018
1/4” – 20 lock nut
2
7
21-135-001
Motor
1
21
37030
1/2” – 13 lock nut
4
8 21-156-002 Electronic touchpad control
1
22 20-538-002
Assembly, carriage, stretch wrap
carrier
1
9
21-034-010
24V battery charger
1
23
20-016-076
Bracket, roller
2
10
21-139-001
12V battery
2
24
20-525-001
Weldment, handle
1
11
21-034-025
Flanged inlet sleeve with locking ring
1
25
33011
1/2” flat washer
4
12 11012
1/
4
” – 20 x 21/
4
” HHCS #2 zinc-plated
bolt
4
26 21-156-006
Accessories, electrical control box,
Curtis 1210-2401
1
13
33004
1/4” type A narrow flat washer
2
27
21-024-042
Motor cover
1
14
33008
3/8” flat washer
20
*28
20-522-004
Hand control switch, pressure sensor
1
*Not shown in exploded parts diagram.
Detail A

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 10 of 17
Accessory carriage attachments:
The following carriage attachments can be purchased separately and replace the standard load deck when installed.
See “Installing accessory carriage attachments” on page 11 for installation instructions.
Installing accessory carriage attachments:
Each attachment (except PEL-VBLK) includes a carriage mounting plate with 8 bolt holes as shown in the diagram below.
Use the wider bolt pattern (see red rectangle) to mount your attachment to the carriage of any steel quick lift. To mount an
attachment to an aluminum quick lift, use the narrow bolt pattern (shaded blue).
Dimensions of mounting plate:
Step 1: Remove the 3/
8
” – 16 x 11/
2
” bolts that fasten the deck
to the carriage.
Bolt
Carriage
Step 2: Fasten the mounting plate of your attachment to the carriage
using the hardware removed during step 1. The correct top-to-bottom
orientation of each attachment is indicated in the “Accessory carriage
attachments” section above.
Attachment (PEL-RR shown):
Mounting
plate
PEL-DSPIN
Weight = 20 lb.
Capacity:
PEL-88 & PEL-88-A = 175 lb.
PEL-100 & PEL-100-A = 125 lb.
PEL-400-57/72 = 400 lb.
PEL-HOOK
Weight = 9 lb.
Capacity:
PEL-88 & PEL-88-A = 175 lb.
PEL-100 & PEL-100-A = 125 lb.
PEL-400-57/72 = 400 lb.
PEL-PAIL
Weight = 20 lb.
Capacity = 125 lb.
PEL-RR
Weight = 40 lb.
Capacity = 125 lb.
PEL-SPIN
Weight = 11 lb.
Capacity:
PEL-88 & PEL-88-A = 175 lb.
PEL-100 & PEL-100-A = 125 lb.
PEL-400-57/72 = 400 lb.
PEL-VBLK
Weight = 27 lb.
Capacity:
PEL-88; PEL-88-A
= 175 lb.
PEL-100; PEL-100-A
= 125 lb.
PEL-400-57/72
= 400 lb.
PEL-CONV
Weight = 40 lb.
Capacity = 175 lb.
Installing attachment PEL-VBLK:
1. Disconnect the deck
from the carriage
arms by removing
the 10-32 x 1” flat
head bolts.
2. Center the
attachment on the
arms and align bolt
holes in the VBLK
with the bolt holes in
the carriage arms.
Use the bolts to
fasten the VBLK
attachment to the
carriage arms.
Bottom side of
PEL-VBLK
Bolt
Carriage
arms
NOTE: The PEL-VBLK can be mounted with the groove
facing forward or to the side.

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 11 of 17
FIG. 5: Electrical circuit diagram

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 12 of 17
Operation Instructions:
Place a load on the load deck. The weight of the load must not exceed the capacity of your lifter. Capacity
information appears “Specifications” diagrams on page 3 as well as on label 287 (see “Labeling diagrams” on p. 16).
Always center the load on the deck before raising it, and make sure that the load does not hang over the sides of the
deck.
Deck position and raising/lowering speed are controlled by inputs from the touchpad controller or optional
handheld pendant control. To elevate or lower the deck, press and hold either the “RAISE” button or the “LOWER”
button on the touchpad. If your lifter is equipped with a pendant control, press the left button to raise the deck or the
right button to lower it. Deck travel speed is also adjustable. Press the “FASTER” button to increase speed or the
“SLOWER” button to decrease speed. The percentage of battery charge remaining is displayed in a small window in
the touchpad as well.
Chain tension adjustment procedure:
[NOTES: Unload the deck before beginning the adjustment.]
PEL-88 & PEL-100 model lifters:
1. Raise the deck halfway.
2. Locate the tensioning bolts. A bolt is present
at each end of the chain.
3. Using 7/16” crescent wrenches loosen the 2
jamb nuts (2) by turning them
counterclockwise. Loosen the jamb nuts so
that they are close to the ends of the bolts.
4. Raise the deck to the top of the mast.
5. Turn each tensioning nut (3) until the chain
can be pulled ~3in. away from the mast at the
midpoint of the mast. Turn both nuts equally.
6. Lower the deck by pressing the LOWER
button. Continue to hold the button for 2
seconds after the deck reaches the lower
travel limit and stops moving. If the chain
jumps on the sprocket, raise the platform to
the top of the mast. Tighten one of the
tensioning nuts by another half turn. Repeat
the first part of this step. If the chain no longer
jumps on the sprocket, proceed to step 7.
7. Raise the deck halfway up the mast. Turn the
jamb nuts by hand until they are firmly pressed
against the tensioning nuts. Then, wrench-
tighten each jamb nut.
Tensioning bolt
Tensioning nut
Jamb nut
*Mast cover not
shown to improve
visibility of
fasteners
Midpoint of mast
(see step 5)

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 13 of 17
Chain tension adjustment procedure:
[NOTES: 1) Unload the deck before beginning the adjustment. 2) Numbers in parentheses correspond to item numbers
in the diagram.]
PEL-400 series lifters:
8. Raise the deck halfway.
9. Locate the chain holding nuts. Turn the four
holding nuts counterclockwise to loosen
them. Loosen the nuts until they are close to
the head of the chain holding bolts. Use a 3/4”
wrench to loosen the nuts and a 1/2” wrench
to hold the chain to prevent it from turning.
10. Raise the deck to the top of the mast.
11. Use the 3/4” and 1/2” wrenches to tighten all of
the chain tensioning nuts (i.e. wind them
further onto the bolts). Turn all of the nuts
equally. Tighten the nuts until the chains can
only be pulled ~2.5 inches from the front of
the mast. Slack in both chains should be
equal.
12. Lower the deck by pressing the LOWER
button. Continue to hold the button for 2
seconds after the deck reaches the lower
travel limit and stops moving. If the chain
jumps on the sprocket, raise the platform to
the top of the mast. Tighten the tensioning
nuts by another half turn; then repeat the first
part of this step. If the chain no longer jumps
on the sprocket, proceed to the next step.
13. Raise the deck halfway up the mast. Turn all
four of the holding nuts by hand until they are
firmly pressed against the tensioning
brackets. Wrench-tighten each nut to make
sure that the connections are secure.
Chain holding nut (1)
Tensioning bracket (3)
Chain tensioning nut (4)
Chain holding bolt (2)
1
2
4

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 14 of 17
Battery Charger Operation (DC-powered units only):
Working on lead-acid batteries is dangerous. Batteries contain sulfuric acid and produce explosive
gases. A battery explosion could result in loss of eyesight or serious burns.
•DO NOT smoke near the battery or expose the battery to a spark or flame.
•ONLY charge batteries in dry, well-ventilated locations.
•DO NOT lay tools or metallic items on top of a battery. NEVER touch both terminals simultaneously! Remove personal
items such as rings, bracelets, necklaces, and watches. A battery can produce enough voltage to weld jewelry to metal.
•Always have plenty of fresh water and soap nearby in case contact with battery acid occurs.
•Operating the battery with low voltage can cause premature motor contact failure.
•The charger is equipped with an external ground wire (small green wire). To properly ground the charger, ensure that this
wire is always connected to the frame of the lifter.
•Confirm that all battery connections are sound and clean. Remove all accumulated deposits on the terminals.
•Replace defective electrical cords and wires immediately.
•DO NOT use the charger if the flanged inlet is damaged.
•DO NOT connect the charger to a damaged extension cord.
Every DC powered PEL is equipped with an onboard battery charger with a flanged electrical inlet. The charger is current
limited and will not exceed its rated output even if loads are placed on the battery while it is charging. The charger fuse will break
if it is connected in reverse polarity.
To charge the battery:
1.) Plug the charger into an 115V, 60 Hz receptacle by connecting the flanged inlet on the charger to an extension cord. Plug the
other end of the cord into a wall socket. Use a short, thick extension cord.
2.) When properly connected, the charge LED will indicate the status of charge current flowing to the battery.
•If only the red LED is on, the charger is providing full output to the battery.
•If both the red and green LED's are on, the charger is "topping off" the battery.
•When only the green LED is on, the unit is providing a "float" (maintenance) charge.
•DO NOT leave the charger on for long periods after the battery is fully charged.
3.) Unplug the charger before using the lifter. Failure to do so could cause damage to cords, receptacles, etc.
TROUBLESHOOTING--If the charger does not work:
1) Make sure all battery connections sound.
2) Confirm that the AC power source (e.g. wall socket) is supplying power.
3) Examine the fuse (see diagram above). Replace only with a fuse having the same rating as the original fuse.
4) Determine battery condition. It may take some time before current begins to flow through a highly sulfated battery.
NOTE: Specifications are subject to change
without notice.

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 15 of 17
Inspections & Maintenance:
Regular maintenance is essential to keep this product in normal working order. Before beginning
maintenance, completely unload and lower the deck. Always use this product in accordance with the instructions in
this manual.
oKeep the product clean & dry. Lubricate moving parts at least once per month.
oONLY use manufacturer-approved replacement parts. Vestil is not responsible for issues or malfunctions that
result from the use of unapproved replacement parts.
Inspect the following components at least once per month:
1. Wiring: inspect the electrical wiring for cuts or frays.
2. Casters: examine the casters and confirm normal operating condition.
3. Structure: inspect the base and frame for deformations and cracked welds.
4. Deck, carriage, carriage rollers, and mast: cycle the deck up and down while listening and watching unusual
noise, motion, or binding. Check rollers and retaining hardware for normal condition. If the carriage does not
move smoothly or makes noise as it moves up or down the mast, apply a silicon wax or silicon spray to the
inside of the mast frame.
5. Touchpad and (optional) pushbutton controller: inspect both the touchpad and the handheld controller. Look for
damage that exposes users to risk of electric shock.
6. Battery: check the water level in the battery. (DC models only)
7. Chain: inspect for excessive wear. Particularly examine each chain for stretched, twisted, and cracked links.
Check chain tension and inspect the hardware fastening each chain to the lifting carriage (see pages 12 & 13).
8. Labels (see “Labeling diagram; p. 16): confirm that all labels are in place and easily readable.
9. Surfaces: remove dirt and debris. Remove rust with a steel bristle brush and apply touchup paint to the
affected areas.
Maintenance:
Implement a maintenance program to ensure the proper function and safety of the device. ANSI/ITSDF standard
B56.10, “Safety Standard for Manually Propelled High Lift Industrial Trucks” provides some recommended
maintenance procedures. The standard is freely downloadable from http://www.itsdf.org. The following steps should
be utilized in conjunction with those recommendations.
Step 1: Tag the unit, “Out of Service.”
Step 2: Inspect the lifter as described above. If deformity, corrosion, rusting, or excessive wear of structural members
is present, DO NOT use the lifter. Contact Vestil for instructions.
Step 3: Remove any dirt or other debris from all surfaces.
Step 4: Perform all other necessary adjustments and/or repairs. DO NOT modify the lifter.
Step 5: Make a dated record of the repairs, adjustments and/or replacements.
Replacement Parts:
Our company uses carefully selected parts in our equipment. Whenever parts must be replaced, only use
manufacturer approved replacement parts. To order parts for your equipment, contact Customer Service at the factory.
In any correspondence with the factory please include the Serial Number which is inscribed on the nameplate of the
equipment. Use only the part numbers provided in this Owner's Manual. When ordering parts for AC power units, please
be prepared with the motor phase and voltage of the equipment.

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 16 of 17
Labeling diagram:
Each unit should be labeled at all times as shown in the diagram below. Replace any label that is damaged and/or not
easily readable. Numbers below label images in the diagram correspond to the identification number of each label.
A
A: Label 287
B: Label 454
A
B
E
C
C: Label 208
E: Label 527
D
D
B
C
D: Label 212
E
PEL-88-A
PEL-100-A
PEL-88
PEL-100
PEL-400
F: Label 295
F
F

Rev. 10/3/2019 PEL, MANUAL
Copyright 2018 Vestil Manufacturing Corp. Page 17 of 17
LIMITED WARRANTY
Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship during the
warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the
warranty, after we receive a proper request from the warrantee (you) for warranty service.
Who may request service?
Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized
distributor AND Vestil has been fully paid.
What is an “original part”?
An original part is a part used to make the product as shipped to the warrantee.
What is a “proper request”?
A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the shipping date;
AND 2) a written request for warranty service including your name and phone number. Send requests by any of the following
methods:
Mail Fax Email
Vestil Manufacturing Corporation [phone] [e-mail]
2999 North Wayne Street, PO Box 507 Phone
Angola, IN 46703 [phone]
In the written request, list the parts believed to be defective and include the address where replacements should be delivered.
What is covered under the warranty?
After Vestil receives your request for warranty service, an authorized representative will contact you to determine whether your claim
is covered by the warranty. Before providing warranty service, Vestil may require you to send the entire product, or just the
defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following original dynamic components:
motors, hydraulic pumps, electronic controllers, switches and cylinders. It also covers defects in original parts that wear under
normal usage conditions (“wearing parts”): bearings, hoses, wheels, seals, brushes, batteries, and the battery charger.
How long is the warranty period?
The warranty period for original dynamic components is 1 year. For wearing parts, the warranty period is 90 days. The warranty
periods begin on the date when Vestil ships the product to the warrantee. If the product was purchased from an authorized
distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion, extend the warranty periods
for products shipped from authorized distributors by up to 30 days to account for shipping time.
If a defective part is covered by the warranty, what will Vestil do to correct the problem?
Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact you to
discuss your claim.
What is not covered by the warranty?
1. Labor;
2. Freight;
3. Occurrence of any of the following, which automatically voids the warranty:
•Product misuse;
•Negligent operation or repair;
•Corrosion or use in corrosive environments;
•Inadequate or improper maintenance;
•Damage sustained during shipping;
•Collisions or other incidental contacts causing damage to the product;
•Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written authorization from
Vestil. Modification(s) might make the product unsafe to use or might cause excessive and/or abnormal wear.
Do any other warranties apply to the product?
Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed by law.
Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.