Veto VT-AD5500 User manual

User Manual
FCC Statement
This device complies with part15 ofthe FCC Rules. Operation is subject to the condition that this device
does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by theparty responsible for compliancecould void the
user's authorityto operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part15 ofthe FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency
energyand, ifnotinstalled and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged totry to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consultthe dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated
with minimum distance between 20cm theradiator your body: Use only the supplied antenna.
FCC ID：2AUYQ-VT-AD5500
User Manual:FCC
Product:55 inch Commercial LCD Display
Model:VT-AD5500(CM)
Trade Mark: VETO
Shenzhen VETO Technology Co.,Ltd.
I. Precautions during use
Improper operation maycause electric shock or fire accident. To prevent dangerous situations, please
follow the instructions when installing, using or cleaning. To ensure your safetyand extend the service
life of the touchall-in-one machine, please carefully read the following safetyprecautions before use:
1. Read and understand all instructions before use.
2. Keep the operation manual properlyfor future needs.
3. The warning instructions on the machine and its operation manual must be strictly followed.
4. Allinstructions must be followed during operation.
5. Do not use accessories not recommended by the manufacturer. Accidents may occur due to
improper nearbydevices.
6. Before connecting the AC power cord to the power socket, check whether the power requirements

specified by the touch all-in-one machine are suitable for the local power supply conditions. If you are
unsure of the type ofpower supply youare using, consult your local dealer or power department.
7. Do not press or wind the power cord with anything. Brokenpower cord can cause electric shock or
fire.
8. Do not attempt to repair the machine by yourself. Due to the high-voltage device and other easily
damaged devices in the machine, it will cause various hazards to human bodyor touch the integrated
machine itself. When the touch all-in-one machine fails, it is necessary to find a professional
maintenance personnel for maintenance.
9. When the parts of the machine need to be replaced, please use the parts specified by the
manufacturer or with the same performance as the original parts. Improper use of accessories may
cause fire; danger of electric shock and damage to touch all-in-one machine.
10. To mount the machine on the wall, please installit in the wayrecommended by the manufacturer.
11. Please shut down and unplug the power plug before cleaning the machine. Please use a slightly
wet and soft cloth to clean the machine. Do not use liquid cleanser or spraycleaner whencleaning.
12. When you do not use the machine for a long time, please shut down and unplug the power plug.
13. Please ensure that the air around the machine is smooth and the air vent of the machine cannot
be covered or blocked.
14. Please ensure the infrared touch screenis cleanand tidy to avoid touch failure.
15. Do not put the machine near direct sunlight or heat source, such as radiator, heating equipment
and other hot objects.
II. Product specifications
LCD
PANEL
Sizes
43 inch
49 inch
55 inch
65 inch
Display area(mm)
700×394mm 16:9
930×523mm 16:9
1018x573mm 16:9
1210×682mm 16:9
Resolution
1920×1080 or 3840×2160
Display color
16.7M
Viewing angle
170°/170°
Brightness
450cd/㎡
Contrast ratio
4000：1
Response time
4ms
Life time(hrs)
≥60000
Touch
Screen
Touch points
10 points touch
Positioning accuracy
±2mm
Transmittance
≥92%
Hardness
7H
Response time
≤10ms
Service life
Single point more than 60 million times
PC
System
Win7 /Win8/Win10 (Optional)
Main board
H81/H110 (Optional)
CPU
Core I3-4150 /I5-7200 ect (Optional)
RAM
4GB/8GB/16GB (Optional)
Hard Disk
500G HHD/128G SSD (Optional)

Graphics card
Intel HD Graphics (Optional)
Speaker
8Ω5W ×2
input voltage
AC 100～240v 50/60HZ
Power
Maximum power
consumption
≤75W
Standby power
≤3W
≤80W
≤100W
≤120W
Material
Cold drawn steel SPCC / aluminum panel / custom made, metal baking paint,
independent power supply, internal components plating, rust proof,
antimagnetic, antistatic.
Appear
ance
Color
Silver / Black / custom made
Installation mode
Floor standing
Operating
temperature / humidity
0℃～50℃/20%～80%
Environ
ment
Storage temperature /
humidity
-10℃～60℃/5～95%
Remarks
Multi point function: support to enlarge, shrink, rotate, move and other
multimedia content such as 3D model, picture, video, song,etc. operation
functions can be added according to customer requirements.
*Motherboard. CPU, hard disk, memory, touch screen all can be optional.
*The above parameters are for reference only,andthe specific data is subject to
the real object.
III.equipment list
1. Manual (one)
2. Kiosks Host (one)
3. Base (one)
4. AC power line (one)
5. Product warrantycard (one copy)
6. Product certificate (one)
7. Mounting screws (several)
IV.Installation diagram
1. Lay the kiosk host on a flatsurface (screen face up);
2. Then align the hole in the base with the screw hole in the kiosk host
3. Tightenall screws
＋ ＝

DC IN
USB
DVI /OUT
HDMI /OUT
AUDIO /OUT
MIC /OUT
LAN
V. key and interface description
POWER LAN USB ON/OFF AC100-240V
The key and interface are for reference only. Please refer to the material object.
VI. troubleshooting
Whenthe machine fails, please check the phenomena listed in the following table to see whether
itis caused byoperationproblems or the machine itself. After confirming the cause of the fault, if it is
caused by improper operation, you can handle it by yourself according to the prompts in the table
below. If it is the fault of the machine itself, please contact the after-sales service center or the dealer.
Fault phenomenon
Cause of failure
Resolvent
No screen response (black
screen) no image display
No power supply for the machine
Check whether the power supply is
normal and whether the power socket is
in good contact; check whether the
machine power switch is on
The machine is not turned on
Check whether the computer switch is
on (red button)
Computer standby
Double click the touch screen
Machine damage
Contact the dealer or manufacturer
No response from touch
screen (inaccurate
positioning)
There are foreign objects stuck
on the touch screen
Clean the touch screen; restart the
computer
Touch screen positioning error
Recalibrate the touch screen
Touch screen cable loose
Check the connecting wire to ensure
good contact
Touch screen damage
Contact dealer or manufacturer
Unable to access the system
System damage
Repair system
Enter auto repair
Select "start Windows normally" with the
keyboard

Machine damage
Contact the dealer or manufacturer
No voice
Sound card drive failure;
computer set to mute; speaker
problem
Check whether the sound card driver is
installed; check whether the volume of
the computer is mute; replace the
speaker
No internet access
Network card drive failure;
network cable interface is not
contacted well
Check whether the driver of the network
card is installed; check whether the
network cable is connected (whether the
indicator light of the network interface is
on)
Incorrect network configuration
Set up the correct network configuration
Touch screen calibration method:
1. Select the touch screen calibration program of win7;Open the control panel → hardware and
sound → Tablet PC settings → calibration screen → calibrate as prompted
2. Ask the supplier for touchscreen calibrationsoftware