Viatec HAC-HDB3100P/N2812AI User manual

HDCVI HD ICR Varifocal (IR) Vandalproof
Analog Dome Camera
User’s Manual
Version 1.0.0

i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Functions .......................................................................................................................1
1.4 Specifications................................................................................................................1
2Framework...................................................................................................................................3
2.1 Dimensions....................................................................................................................3
2.2 Structure ........................................................................................................................3
3Installation ...................................................................................................................................7
3.1 Device Installation Introduction ..................................................................................7
3.2 Device Installation Steps.............................................................................................8
3.2.1 General Installation ...............................................................................................8
3.2.2 Manual Varifocal Lens Operation .....................................................................11
3.2.3 Side Cable Exit ....................................................................................................12
3.2.4 Cable Connection................................................................................................13
4Menu...........................................................................................................................................14
Appendix Toxic or Hazardous Materials or Elements ...............................................................17

ii
Welcome
Thank you for purchasing our analog camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC (24V AC) in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series analog camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
The working temperature ranges from -30℃to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance

iv
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

1
1General Introduction
1.1 Overview
This series megapixel analog HD camera conforms to the HDCVI standard. It supports video
signal high-speed long distance transmission without any delay. It can be controlled by the
DVR conforming to the HDCVI.
1.2 Features
zHigh-performance image sensor, megapixel definition.
zHDCVI analog port, support 75-3 coaxial transmission without any loss. 720P resolution
supports over 500m and 1080P supports as long as 300m.
zHigh speed, long distance real-time transmission.
zSupport HD video/audio, 485 control signal coaxial transmission.
zSupport OSD (on-screen display), suitable for user self-defined setup.
zSupport IO alarm, RS-485 control.
zSupport privacy mask, image digital zoom.
zSupport DC12V/AC24V power supplying.
zSupport 3D noise reduction(denoise),excellent performance in low illumination
environment.
zIP66 compliance.
zSupport ICR switch to realize surveillance both in the daytime and at night.
zSupport IR function. (For IR series product only.)
1.3 Functions
HDCVI Specification
HDCVI（High Definition Composite Video Interface）is an over-coaxial –cable analog HD
video transmission standard. The technology renders two HD video formats: 1920H
(1920*1080) &1280H (1280*720) by progressive scanning.
OSD
User-friendly on-screen display for you to select the different functions.
RS-485
Can connect to peripheral device via 485 serial port. Support various control protocols to
realize rear-end device activation.
ICR
The IR cut removal is to filter the IR light in the daytime and then auto switch to the general
fitter at night. This function allows the camera to output the high sensitivity and clear video.
1.4 Specifications
Please refer to the following sheet for specification.

2
HDCVI HD Megapixel ICR Varifocal (IR) Vandalproof Analog Dome Camera
Model
Parameter HAC-
HDB3100P/N-
2812AI
HAC-
HDBW3100P/N-
IR2-2812AI
HAC-
HDB3200P/N-
3312AI
HAC-
HDBW3200P/N-
IR2-3312AI
Video Processor 1/3"-inch CMOS 1/2.9"-inch CMOS
Video Format PAL/NTSC
Effective Pixel 1280 (H)*720 (V) 1920 (H) *1080 (V)
Resolution 720P 1080P
Min Illumination 0.05Lux/F1.4(Color mode),
0Lux(IR light on)
0.1Lux/F1.4(Color mode),
0Lux(IR light on)
Electronic Shutter Support slow shutter. 1/1s~1/10000s.
Video Frame Rate PAL:1280*720@25fps
NTSC: 1280*720@30fps
PAL:1920*1080@25fps
NTSC: 1920*1080@30fps
Lens Type φ14 port 2.8-
12mm varifocal
auto aperture
lens
φ14 port 2.8-
12mm varifocal
auto aperture
lens
φ14 port 3.3-
12mm varifocal
auto aperture
lens
φ14 port 3.3-
12mm varifocal
auto aperture
lens
Day/Night Switch Auto.
Video Output 1-channel BNC analog high definition video output.
Audio Output Reuse video output channel.
SNR Above 50 dB(AGC OFF)
Max IR Distance / 30m / 30m
OSD Menu Control Support
SCENE INDOOR/OUTDOOR/WDR
EXPOSURE AUTO/AUTO IRIS/AUTO SHUTTER/MANUAL
FUNCTION WB/WDR/NR/MIRROR/DAY&NIGHT/HLC/BLC
IMAGE MODE/COLOR CNT/SHARPNESS/SHARP
CNT/BRIGHTNESS/SATURATION/HUE/GAMMA
ADVANCED MOTION DETECT/DIGITAL ZOOM/PRIVACY MASK/FREEZE/RS-
485/CAMERA ID/LANGUAGE/SYSTEM INFO
OSD
EXIT INDOOR/CAMERA RESTART/BACK
Communication Port 1-channel RS485 port (Support PELCOD, PELCOP, and industrial protocol.)
Working Temperature -30℃~+60℃
Working Humidity 20%~90%RH
Power AC24V/DC12V
Power Consumption 7W Max 10W MAX 8W MAX 11W Max
Dimension(mm) ¢151×119
Weight 1000g 1100g 1000g 1100g

3
2Framework
2.1 Dimensions
Please refer to the following figures for the dimension information. The unit is mm. See Figure
2-1 and Figure 2-2.
Figure 2-1
Figure 2-2
2.2 Structure
For the non-IR series product, the interface is shown as in Figure 2-3 and Figure 2-4.

4
Figure 2-3
Figure 2-4
For the IR manual varifocal series product, the interface is shown as in Figure 2-5 and Figure
2-6.

5
Figure 2-5
Figure 2-6
Please refer to the following sheet for detailed information.

6
SN Component
Name Function
1
Standard
definition video
output and 5-
direction button
input port
/
2 DC12V/AC24V
power port
/
3 External cable
exit
/
4 High definition
video output port
/
5 I/O port It includes alarm output, audio input, 485 control signal,
standard definition video output.
6 5-direction
buttons
These five buttons are for OSD menu operation.
Please use the up/down button to select the item and
use the left/right button to select the option. The button
in the middle is to confirm current operation.
7 Power and
system indicator
light
The light becomes yellow when the power supplying is
OK.
The light becomes red when system properly loaded.
8 Power input port /
9
High definition
video output port BNC port. Output high definition analog video signal.
Please refer to the following sheet for I/O port cable function information.
Port SN Port Name Function Description
1 ALARM_COM Alarm output public end.
2 ALARM_NO Alarm signal output port. Output alarm
signal to alarm device.
3 GND Ground end.
4 AUDIO_IN Input audio signal. It is to receive analog
audio signal from devices such as pickup.
5 GND Ground end.
6 485_B RS485 control signal input end B.
7 485_A RS485 control signal input end A.
8 GND Ground end.
9 VIDEO_SD_OUT Output standard definition video signal.

7
3Installation
Important
zBefore you complete the installation and setup, do not remove the electrostatic
attraction film on the transparent enclosure. Otherwise it may result in injury.
zAfter remove electrostatic attraction film, do not touch dome enclosure in case it
may leave stain.
zThe dome camera mainly uses the in-ceiling installation. Before the installation,
please make sure the installation surface can sustain at least 3X weight of the
bracket and the camera.
3.1 Device Installation Introduction
Please refer to Figure 3-1 and Figure 3-2 for device installation space information. You can
use screws (diameter is less than 4.5mm) to secure the device. You can see there are
installation position map and installation screws in the accessories bag for you to install the
device conveniently.
Figure 3-1
Figure 3-2

8
3.2 Device Installation Steps
3.2.1 General Installation
The general interface is shown as in Figure 3-3.
Figure 3-3
Step 1
Take the installation position map from the accessories bag and then paste it on the
installation ceiling or the wall according to the monitor area. Please dig three bottom holes of
the plastic expansion bolts according to the map. Take three expansion bolts from the
accessories bag and then insert them to the holes you just dug and then fix firmly. If you need
to dig a hole to pull through the cable, you need to dig a cable exit hole (The diameter is more
than 28mm) on the installation surface according to the installation positioning map.
Step 2
Use the inner hex wrench from the accessories bag to unfasten the 3 hex screws on the dome
camera enclosure to open it.
Step 3
Please remove the device cable port (Provided) and the power terminal (②and ④in chapter
2.2.) Use the inner hex wrench (Provided) to remove the 2 inner hex screws from the dome
driver module. Then please follow the prompt on the device to push the metal hook to two
sides. Remove the dome driver module from the chassis. See Figure 3-4.

9
Figure 3-4
Step 4
Adjust the chassis of the device to the proper position and pull the cable to the cable exit of the
installation surface. Line up the holes of the chassis to the three expansion bolt holes you dug
in Step 1. Take three ST3.0 self-tapping screws and secure them in the three plastic
expansion bolts. Now the chassis is secure on the installation surface.
Important
Please earth the device GND hole (GND) to enhance the reliability of the device. The GND
port is near the cable exit of the rear panel. The GND screw thread specification is M3-6mm.
Figure 3-5
Step 5
Please refer to the Step 3 to put the driver module back to the metal hooks of the chassis.
Then use the inner hex wrench to secure the two inner hex screws to the chassis. Then
connect the network cable and the power terminal.
Step 6

10
Adjust the lens to the proper angle according to your monitor requirements.
a) For the IR series product, you can skip current step and go the step b) directly. For the non-
IR series product, push the port slightly to remove the decoration enclosure from the black
plastic enclosure. See Figure 3-6.
Figure 3-6
b) Lens pan rotation angle setup. Please refer to Figure 3-7 to unfasten the lock screw A and
adjust the pan monitor angle to the proper position. Then fix the lock screw A. The pan angle
ranges from 0°~+350°.
Figure 3-7
c). Lens tilt rotation angle. Please refer to Figure 3-8 to unfasten the lock screw B and lock
screw C and adjust the tilt monitor angle to the proper position. Then fix the lock screw B and
lock screw C. The tilt angle ranges from -23°~+73°.
Lock Screw A
Adjust lend pan rotation
angle.

11
d). Image pan rotation angle setup. Please refer to Figure 3-8 to turn lock screw D to adjust
the video pan angle. Then fix the lock screw B and C. The video pan angle ranges from
0°~+350°.
Figure 3-8
e) For the manual varifocal series product, please skip current step. Please refer to chapter
3.2.2 for the lens zoom and focus operation of the manual focus series product.
f) For the IR series product, please skip current step and complete the angle setup directly.
For the non-IR series product, please put back the black plastic decoration enclosure to
complete the angle setup.
Important
Please note Figure 3-7 and Figure 3-8 is based on the IR manual varifocal camera. For
the non-IR series product, the lock screw position and the lens angle adjustment are the
same.
Step 7
Line up the dome camera protection enclosure to the cable exit on the side panel. Put the
enclosure back and then use the inner hex wrench to secure the 3 inner hex screws firmly.
Now the installation is complete.
Note
Usually we recommend, after the installation, please take the three white static protection
gaskets from the accessories bag and insert them to the screw holes of the protection
enclosure. It is to enhance device reliability.
3.2.2 Manual Varifocal Lens Operation
The manual varifocal lens interface is shown as in Figure 3-9.
Step 1
Slightly loosen the adjusting screw E and push the adjust screw E to make it swing. Adjust the
lens focus to the proper position according to the displayed video.
Lock screw B/C
Adjust lens tilt rotation
angle.
Lock screw D
Adjust lend pan rotation
angle.

12
Step 2
Slightly loosen the adjusting screw F and push the adjust screw F to make it swing. Adjust the
lens to get the clear video and then fix the adjusting screw firmly.
Step 3
When you are securing the adjusting screw F, you can see the video may become blur. Please
push the adjusting screw E to adjust the video slightly. Please secure the adjust screw E if you
get a clear video.
Figure 3-9
3.2.3 Side Cable Exit
If you adopt side cable exit when you are installing the device, you need to remove the plastic
decoration plug from the side of the chassis. Use the proper tool to dig through the part
specified in Figure 3-10 to form a cable exit. Put the plastic decoration plug back to the chassis
and then pull the cable through the side panel of the chassis.
Figure 3-10
For some special user, he may need the metal protection tube to protect when he pulls through
the cable from the side cable. There is PG11screw thread port when you pull through the cable
from the side panel. Please remove the plastic decoration plug from the side panel of the
chassis and pull through the cable to the tunnel of the PG11 screw thread. Now secure the
tunnel in the PG11 screw threaded hole of the device.
Dig through here
Adjusting Screw E
Adjusting Screw F

13
3.2.4 Cable Connection
The device reserves two cable exits. The pin diameter shall be less than 15mm. One of the
cable exits has M22 screw thread and can work with the default combination cable to remove
the risk of the dragging and pulling of the cable.
The device has two waterproof airproof plugs (One default position is the cable exit of the
chassis of the device and the other is in the accessories bag.). The waterproof airproof plug
has two functions. One is to fill in the cable exit and pull through the cable. It supports the
cable whose diameter ranges from 4.0~6.0. It is very convenient for you to do the waterproof
work when you pull the cable through your own exit. Please refer to the steps listed.
Step 1
Take the waterproof airproof plug out, pull the cable (diameter ranges from 4.0 to 6.0) through
the waterproof airproof plug. See Figure 3-11.
Figure 3-11
Step 2
Before you go to the Step 4 in the chapter 3.2.1 installation steps, please pull through cable
with the waterproof airproof plug to the device chassis via the installation hole at the bottom of
the chassis and then connect the cable pins.
Step 3
Refer to Step 4 and Step 5 in the chapter 3.2.1 installation steps to install and connect the
cable pin to the device and then follow the proper steps to go on the installation.
Important
This series product has the power connection pin and I/O connection pin for you to pull
through the signal cable.

14
4Menu
THE 1ST MENU THE 2ND MENU THE 3RD MENU
SCENE
INDOOR
SCENE
OUTDOOR
SCENE WDR
SCENE
BACK
PAL:MAX SPEED 1/25
NTSC: MAX SPEED
1/30
MIN SPEED 1/10000
PAL:
1/25, 1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425, 1/600,
1/1000, 1/1250, 1/1750, 1/2500,
1/3500, 1/6000, 1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,
1/250,1/350,1/500,1/725,1/1000,1
/1500,1/2000,1/3000,1/4000,1/60
00,1/10000.
PAL:SLOW SHUTTER
1/25
NTSC: SLOW
SHUTTER 1/30
PAL:
1/1 ,1/2 ,1/3,1/6,1/12,1/25
NTSC:
1/1, 1/2, 1/4, 1/8, 1/15, 1/30
SHUTTER
AUTO…
BACK
GAIN 24dB -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS--- It is read-only on auto mode.
EC(+0) OFF,+0,+1,+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC60 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1
00
AUTO
BACK
PAL:
SHUTTER
1/25.
NTSC:SHUT
TER 1/30
PAL:
1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000,
1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,1/250,1/350,1/500,1/725,1/
1000,1/1500,1/2000,1/3000,1/4000,1/6000,1/10000.
GAIN 24dB -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS--- It is read-only on auto iris mode.
EC(+0) OFF,+0,+1,+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC60 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1
00
IRIS
BACK
PAL:MAX SPEED 1/25
NTSC: MAX SPEED
1/30
MIN SPEED 1/10000
PAL:
1/25, 1/50, 1/75, 1/100, 1/120,
1/150, 1/215, 1/300, 1/425, 1/600,
1/1000, 1/1250, 1/1750, 1/2500,
1/3500, 1/6000, 1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,
1/250,1/350,1/500,1/725,1/1000,1
/1500,1/2000,1/3000,1/4000,1/60
00,1/10000.
PAL:SLOW SHUTTER
1/25
NTSC: SLOW
SHUTTER 1/30
PAL:
1/1 ,1/2 ,1/3,1/6,1/12,1/25
NTSC:
1/1, 1/2, 1/4, 1/8, 1/15, 1/30
EXPOSURE
SHUTTER SHUTTER
AUTO…
BACK

15
GAIN 24dB -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS--- It is read-only on auto shutter mode.
EC(+0) OFF,+0,+1.+2,+3,+4,+5,+6,+7,-1,-2,-3,-4,-5,-6,-7
LLC60 0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,1
00
BACK
SHUTTER PAL:
1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425,
1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000,
1/10000
NTSC:
1/30,1/60,1/90,1/100,1/125,1/180,1/250,1/350,1/500,1/725,1/
1000,1/1500,1/2000,1/3000,1/4000,1/6000,1/10000.
GAIN 24dB -1,0,2,4,6,8,10,12,14,16,18,20,22,24,26,28（DB）
LENS--- MODE OPEN, MODE
OFF
EC(+0) It is read-only on manual mode.
LLC60 It is read-only on manual mode.
MANUAL
BACK
AUTO
INDOOR
OUTDOOR
ONE PUSH
ATW
RED GAIN 087 000-255MANUAL…
BLUE GAIN 051 000-255
OUTDOOR
AUTO
SODIUM
AUTO
WB
SODIUM
OFF
INTENSITY2 1-4
MOTION COMP---
WDR
ON…
RETURN
2D-NR2 OFF, 1-5
3D-NR2 OFF, 1-5
NR…
BACK
MIRROR OFF, V-FLI,H-FLIP, CENTRE
SWITCH POINT 7 1-7
TOLERANCE 5 1-6
DAYÆNIGHT 5S 2S-30S
NIGHT ÆDAY 5S 2S-30S
AUTO …
BACK
DAY
D/N
NIGHT
HLC OFF, 1, 2
BLC OFF,1, 2
FUNCTION
BACK
MODE CUSTOM , FLAMBOYANT,SOFT,
Note: For non-custom mode, the rest parameters are read-only.
HUE CNT 00~15
SHARPNESS 00~15
SHARP CNT 00~15
BRIGHT 000~255
SATURATION 000~255
IMAGE
HUE 000~255