Videoswitch CMOR-D18? CMOR-D26 User manual

Page 1
CMOR
Professional Dome
User Manual
Product ranges covered by this manual
CMOR-D18 & CMOR-D26
Professional Dome
CMOR-PSU-1 CMOR-ALM-16 Options
Document Reference Date Firmware
Vc601e.doc 18/02/2009 From Vc001A82
Videoswitch Telephone [phone]
Ocean House, Redfields Industrial Park Fax [phone]
Redfields Lane, Church Crookham Email [email protected]
Hants GU52 0RD Web www.videoswitch.co.uk

Page 2
Configuring the Dome....................................................4
1.1 Removing the DIP switch cover.............................................................................................4
1.2 Setting the dome address......................................................................................................5
1.3 Setting the dome protocol....................................................................................................10
1.4 Setting the baud rate............................................................................................................10
1.5 Setting the RS485 termination.............................................................................................11
1.6 Replacing the DIP switch cover...........................................................................................11
2Installing the Dome ................................................13
2.1 Fixing the mounting ring.......................................................................................................13
2.2 Securing the bracket............................................................................................................14
2.3 Attaching the CMOR Dome .................................................................................................15
2.4 Attaching the umbilical cable ...............................................................................................15
2.5 Fitting the bracket cover.......................................................................................................16
3Installing Power Supply.........................................17
3.1 Fixing power supply to wall..................................................................................................17
3.2 Power Supply Connections..................................................................................................18
3.2.1 Mains Input ......................................................................................................................18
3.2.2 Connections to dome.......................................................................................................18
3.2.3 Connections to DVR ........................................................................................................19
3.3 Alarm Module Connections..................................................................................................20
3.3.1 Alarm Inputs.....................................................................................................................20
3.3.2 Alarm Grounds.................................................................................................................20
3.3.3 Relay Connections...........................................................................................................20
4Configuring the Alarm Module..............................21
4.1 Normally Open or Closed Alarm Inputs ...............................................................................21
4.2 RS485 Termination..............................................................................................................21
4.3 Setting the alarm module protocol .......................................................................................21
4.4 Setting the alarm module baud rate.....................................................................................22
5Menus......................................................................23
5.1 Menu Navigation..................................................................................................................23
5.1.1 Entering Menu..................................................................................................................23
5.1.2 Moving cursor ..................................................................................................................23
5.1.3 Select...............................................................................................................................23
5.1.4 Cancel..............................................................................................................................23
5.1.5 Exit Menu.........................................................................................................................24
5.2 Login ....................................................................................................................................24
5.3 Setup....................................................................................................................................25
5.3.1 Enter date/time.................................................................................................................25
5.3.2 Daylight Saving................................................................................................................25
5.3.3 Language.........................................................................................................................25
5.3.4 Display.............................................................................................................................25
5.3.5 Passwords .......................................................................................................................25
5.3.6 Datum Check ...................................................................................................................26
5.3.7 Install date/time................................................................................................................26
5.3.8 Clear Settings ..................................................................................................................26
5.4 IR..........................................................................................................................................27

Page 3
5.4.1 IR Mode ...........................................................................................................................27
5.4.2 IR ON level.......................................................................................................................27
5.4.3 IR Off level hysteretic.......................................................................................................27
5.4.4 Auto IR delay ...................................................................................................................27
5.4.5 IR ON times .....................................................................................................................27
5.4.6 IR Power ..........................................................................................................................27
5.5 Camera ................................................................................................................................28
5.5.1 Main camera settings.......................................................................................................28
5.5.2 Context Camera...............................................................................................................29
5.5.3 Invert Image.....................................................................................................................29
5.6 Keyboard..............................................................................................................................29
5.6.1 Restore Mode (Preset & Tours).......................................................................................29
5.6.2 Restore delay (Preset & Tours) .......................................................................................29
5.6.3 Joystick/Speed Curve......................................................................................................29
5.6.4 Zoom Ratio ......................................................................................................................30
5.6.5 Max Joystick Speed.........................................................................................................30
5.6.6 Pan Limits........................................................................................................................30
5.6.7 Iris key usage...................................................................................................................30
5.7 Presets.................................................................................................................................30
5.7.1 Set Preset........................................................................................................................30
5.7.2 Preset Titles.....................................................................................................................30
5.7.3 Preset Speed...................................................................................................................31
5.8 Tours....................................................................................................................................31
5.9 Privacy .................................................................................................................................32
5.10 Alarms..................................................................................................................................32
5.10.1 New alarm dwell...............................................................................................................32
5.10.2 Alarm cycle time...............................................................................................................32
6Technical Data........................................................33
6.1 CMOR-D18 Dome................................................................................................................33
6.1.1 Camera ............................................................................................................................33
6.1.2 IR Illumination..................................................................................................................33
6.1.3 Power requirements.........................................................................................................33
6.1.4 Physical and Environmental.............................................................................................33
6.2 CMOR-PSU-1 Power Supply...............................................................................................33
6.2.1 Power requirements.........................................................................................................33
6.2.2 Physical and Environmental.............................................................................................33
6.2.3 Safety...............................................................................................................................33
6.3 CMOR-ALM-16 Alarm Module.............................................................................................34
6.3.1 Alarm Inputs/Outputs .......................................................................................................34
6.3.2 Physical and Environmental.............................................................................................34
6.4 Brackets and Cables............................................................................................................34
6.4.1 Wall bracket.....................................................................................................................34
6.4.2 Corner adaptor.................................................................................................................34
6.4.3 Swan-neck bracket ..........................................................................................................34
6.4.4 Pendant bracket...............................................................................................................34
6.4.5 Cables..............................................................................................................................34
6.5 CE Marking ..........................................................................................................................34

Page 4
Configuring the Dome
The CMOR dome is supplied with DIP switches set for the following configuration:
Twisted pair: Address: 1
Protocol: Videoswitch VXP4
Baud rate: 9600 baud,
Termination: ON
Up-the-coax: BBV compatible
8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8
1 1 0 0 0 0 0 0 0
6-way DIP switch
Protocol, baud, termination 123456
VXP4&Coax/9600 baud/On 0 0 0 0 0 1
1.1 Removing the DIP switch cover
If you need to change DIP switch settings, you may do so either before or after the dome is
mounted on its bracket, whichever is more convenient.
•Using a large flat bladed screwdriver, unscrew the DIP switch access screw (A) on
the rear of the dome by turning counter-clockwise

Page 5
1.2 Setting the dome address
•Set the 8-way switch (A) to the required address (camera number) of the dome as
per the table below. “0” represents OFF (down) and “1” represents ON (up).
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
not used 0 0 0 0 0 0 0 0 16 0 0 0 0 1 0 0 0
1 1 0 0 0 0 0 0 0 17 1 0 0 0 1 0 0 0
2 0 1 0 0 0 0 0 0 18 0 1 0 0 1 0 0 0
3 1 1 0 0 0 0 0 0 19 1 1 0 0 1 0 0 0
4 0 0 1 0 0 0 0 0 20 0 0 1 0 1 0 0 0
5 1 0 1 0 0 0 0 0 21 1 0 1 0 1 0 0 0
6 0 1 1 0 0 0 0 0 22 0 1 1 0 1 0 0 0
7 1 1 1 0 0 0 0 0 23 1 1 1 0 1 0 0 0
8 0 0 0 1 0 0 0 0 24 0 0 0 1 1 0 0 0
9 1 0 0 1 0 0 0 0 25 1 0 0 1 1 0 0 0
10 0 1 0 1 0 0 0 0 26 0 1 0 1 1 0 0 0
11 1 1 0 1 0 0 0 0 27 1 1 0 1 1 0 0 0
12 0 0 1 1 0 0 0 0 28 0 0 1 1 1 0 0 0
13 1 0 1 1 0 0 0 0 29 1 0 1 1 1 0 0 0
14 0 1 1 1 0 0 0 0 30 0 1 1 1 1 0 0 0
15 1 1 1 1 0 0 0 0 31 1 1 1 1 1 0 0 0

Page 6
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
32 0 0 0 0 0 1 0 0 48 0 0 0 0 1 1 0 0
33 1 0 0 0 0 1 0 0 49 1 0 0 0 1 1 0 0
34 0 1 0 0 0 1 0 0 50 0 1 0 0 1 1 0 0
35 1 1 0 0 0 1 0 0 51 1 1 0 0 1 1 0 0
36 0 0 1 0 0 1 0 0 52 0 0 1 0 1 1 0 0
37 1 0 1 0 0 1 0 0 53 1 0 1 0 1 1 0 0
38 0 1 1 0 0 1 0 0 54 0 1 1 0 1 1 0 0
39 1 1 1 0 0 1 0 0 55 1 1 1 0 1 1 0 0
40 0 0 0 1 0 1 0 0 56 0 0 0 1 1 1 0 0
41 1 0 0 1 0 1 0 0 57 1 0 0 1 1 1 0 0
42 0 1 0 1 0 1 0 0 58 0 1 0 1 1 1 0 0
43 1 1 0 1 0 1 0 0 59 1 1 0 1 1 1 0 0
44 0 0 1 1 0 1 0 0 60 0 0 1 1 1 1 0 0
45 1 0 1 1 0 1 0 0 61 1 0 1 1 1 1 0 0
46 0 1 1 1 0 1 0 0 62 0 1 1 1 1 1 0 0
47 1 1 1 1 0 1 0 0 63 1 1 1 1 1 1 0 0
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
64 0 0 0 0 0 0 1 0 80 0 0 0 0 1 0 1 0
65 1 0 0 0 0 0 1 0 81 1 0 0 0 1 0 1 0
66 0 1 0 0 0 0 1 0 82 0 1 0 0 1 0 1 0
67 1 1 0 0 0 0 1 0 83 1 1 0 0 1 0 1 0
68 0 0 1 0 0 0 1 0 84 0 0 1 0 1 0 1 0
69 1 0 1 0 0 0 1 0 85 1 0 1 0 1 0 1 0
70 0 1 1 0 0 0 1 0 86 0 1 1 0 1 0 1 0
71 1 1 1 0 0 0 1 0 87 1 1 1 0 1 0 1 0
72 0 0 0 1 0 0 1 0 88 0 0 0 1 1 0 1 0
73 1 0 0 1 0 0 1 0 89 1 0 0 1 1 0 1 0
74 0 1 0 1 0 0 1 0 90 0 1 0 1 1 0 1 0
75 1 1 0 1 0 0 1 0 91 1 1 0 1 1 0 1 0
76 0 0 1 1 0 0 1 0 92 0 0 1 1 1 0 1 0
77 1 0 1 1 0 0 1 0 93 1 0 1 1 1 0 1 0
78 0 1 1 1 0 0 1 0 94 0 1 1 1 1 0 1 0
79 1 1 1 1 0 0 1 0 95 1 1 1 1 1 0 1 0

Page 7
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
96 0 0 0 0 0 1 1 0 112 0 0 0 0 1 1 1 0
97 1 0 0 0 0 1 1 0 113 1 0 0 0 1 1 1 0
98 0 1 0 0 0 1 1 0 114 0 1 0 0 1 1 1 0
99 1 1 0 0 0 1 1 0 115 1 1 0 0 1 1 1 0
100 0 0 1 0 0 1 1 0 116 0 0 1 0 1 1 1 0
101 1 0 1 0 0 1 1 0 117 1 0 1 0 1 1 1 0
102 0 1 1 0 0 1 1 0 118 0 1 1 0 1 1 1 0
103 1 1 1 0 0 1 1 0 119 1 1 1 0 1 1 1 0
104 0 0 0 1 0 1 1 0 120 0 0 0 1 1 1 1 0
105 1 0 0 1 0 1 1 0 121 1 0 0 1 1 1 1 0
106 0 1 0 1 0 1 1 0 122 0 1 0 1 1 1 1 0
107 1 1 0 1 0 1 1 0 123 1 1 0 1 1 1 1 0
108 0 0 1 1 0 1 1 0 124 0 0 1 1 1 1 1 0
109 1 0 1 1 0 1 1 0 125 1 0 1 1 1 1 1 0
110 0 1 1 1 0 1 1 0 126 0 1 1 1 1 1 1 0
111 1 1 1 1 0 1 1 0 127 1 1 1 1 1 1 1 0
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
128 0 0 0 0 0 0 0 1 144 0 0 0 0 1 0 0 1
129 1 0 0 0 0 0 0 1 145 1 0 0 0 1 0 0 1
130 0 1 0 0 0 0 0 1 146 0 1 0 0 1 0 0 1
131 1 1 0 0 0 0 0 1 147 1 1 0 0 1 0 0 1
132 0 0 1 0 0 0 0 1 148 0 0 1 0 1 0 0 1
133 1 0 1 0 0 0 0 1 149 1 0 1 0 1 0 0 1
134 0 1 1 0 0 0 0 1 150 0 1 1 0 1 0 0 1
135 1 1 1 0 0 0 0 1 151 1 1 1 0 1 0 0 1
136 0 0 0 1 0 0 0 1 152 0 0 0 1 1 0 0 1
137 1 0 0 1 0 0 0 1 153 1 0 0 1 1 0 0 1
138 0 1 0 1 0 0 0 1 154 0 1 0 1 1 0 0 1
139 1 1 0 1 0 0 0 1 155 1 1 0 1 1 0 0 1
140 0 0 1 1 0 0 0 1 156 0 0 1 1 1 0 0 1
141 1 0 1 1 0 0 0 1 157 1 0 1 1 1 0 0 1
142 0 1 1 1 0 0 0 1 158 0 1 1 1 1 0 0 1
143 1 1 1 1 0 0 0 1 159 1 1 1 1 1 0 0 1

Page 8
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
160 0 0 0 0 0 1 0 1 176 0 0 0 0 1 1 0 1
161 1 0 0 0 0 1 0 1 177 1 0 0 0 1 1 0 1
162 0 1 0 0 0 1 0 1 178 0 1 0 0 1 1 0 1
163 1 1 0 0 0 1 0 1 179 1 1 0 0 1 1 0 1
164 0 0 1 0 0 1 0 1 180 0 0 1 0 1 1 0 1
165 1 0 1 0 0 1 0 1 181 1 0 1 0 1 1 0 1
166 0 1 1 0 0 1 0 1 182 0 1 1 0 1 1 0 1
167 1 1 1 0 0 1 0 1 183 1 1 1 0 1 1 0 1
168 0 0 0 1 0 1 0 1 184 0 0 0 1 1 1 0 1
169 1 0 0 1 0 1 0 1 185 1 0 0 1 1 1 0 1
170 0 1 0 1 0 1 0 1 186 0 1 0 1 1 1 0 1
171 1 1 0 1 0 1 0 1 187 1 1 0 1 1 1 0 1
172 0 0 1 1 0 1 0 1 188 0 0 1 1 1 1 0 1
173 1 0 1 1 0 1 0 1 189 1 0 1 1 1 1 0 1
174 0 1 1 1 0 1 0 1 190 0 1 1 1 1 1 0 1
175 1 1 1 1 0 1 0 1 191 1 1 1 1 1 1 0 1
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
192 0 0 0 0 0 0 1 1 208 0 0 0 0 1 0 1 1
193 1 0 0 0 0 0 1 1 209 1 0 0 0 1 0 1 1
194 0 1 0 0 0 0 1 1 210 0 1 0 0 1 0 1 1
195 1 1 0 0 0 0 1 1 211 1 1 0 0 1 0 1 1
196 0 0 1 0 0 0 1 1 212 0 0 1 0 1 0 1 1
197 1 0 1 0 0 0 1 1 213 1 0 1 0 1 0 1 1
198 0 1 1 0 0 0 1 1 214 0 1 1 0 1 0 1 1
199 1 1 1 0 0 0 1 1 215 1 1 1 0 1 0 1 1
200 0 0 0 1 0 0 1 1 216 0 0 0 1 1 0 1 1
201 1 0 0 1 0 0 1 1 217 1 0 0 1 1 0 1 1
202 0 1 0 1 0 0 1 1 218 0 1 0 1 1 0 1 1
203 1 1 0 1 0 0 1 1 219 1 1 0 1 1 0 1 1
204 0 0 1 1 0 0 1 1 220 0 0 1 1 1 0 1 1
205 1 0 1 1 0 0 1 1 221 1 0 1 1 1 0 1 1
206 0 1 1 1 0 0 1 1 222 0 1 1 1 1 0 1 1
207 1 1 1 1 0 0 1 1 223 1 1 1 1 1 0 1 1

Page 9
8-way DIP switch 8-way DIP switch
Dome
Address 1 2 3 4 5 6 7 8 Dome Address 12345678
224 0 0 0 0 0 1 1 1 240 0 0 0 0 1 1 1 1
225 1 0 0 0 0 1 1 1 241 1 0 0 0 1 1 1 1
226 0 1 0 0 0 1 1 1 242 0 1 0 0 1 1 1 1
227 1 1 0 0 0 1 1 1 243 1 1 0 0 1 1 1 1
228 0 0 1 0 0 1 1 1 244 0 0 1 0 1 1 1 1
229 1 0 1 0 0 1 1 1 245 1 0 1 0 1 1 1 1
230 0 1 1 0 0 1 1 1 246 0 1 1 0 1 1 1 1
231 1 1 1 0 0 1 1 1 247 1 1 1 0 1 1 1 1
232 0 0 0 1 0 1 1 1 248 0 0 0 1 1 1 1 1
233 1 0 0 1 0 1 1 1 249 1 0 0 1 1 1 1 1
234 0 1 0 1 0 1 1 1 250 0 1 0 1 1 1 1 1
235 1 1 0 1 0 1 1 1 251 1 1 0 1 1 1 1 1
236 0 0 1 1 0 1 1 1 252 0 0 1 1 1 1 1 1
237 1 0 1 1 0 1 1 1 253 1 0 1 1 1 1 1 1
238 0 1 1 1 0 1 1 1 254 0 1 1 1 1 1 1 1
239 1 1 1 1 0 1 1 1 255 1 1 1 1 1 1 1 1

Page 10
1.3 Setting the dome protocol
•Set sections 1,2 and 3 of the 6-way switch (B) as per the table below to select the
required protocol. “0” represents OFF (down) and “1” represents ON (up).
Protocol 1 2 3
Videoswitch VXP4 and BBV up-the-coax 0 0 0
Videoswitch VXP4 only 1 0 0
PelcoP 0 1 0
PelcoD 1 1 0
spare 0 0 1
spare 1 0 1
spare 0 1 1
spare 1 1 1
If coax telemetry is not being used, a protocol other than the first one should be selected to
minimise the possibility of spurious commands being received.
1.4 Setting the baud rate
•Set sections 4 and 5 of the 6-way switch (B) as per the table below to select the
required baud rate. “0” represents OFF (down) and “1” represents ON (up).
•The default setting is 9600 baud (both switches OFF)
•PelcoD normally uses 2400 baud
•PelcoP normally uses 4800 baud
Baud rate 4 5
9600 0 0
2400 1 0
4800 0 1
19200 1 1

Page 11
1.5 Setting the RS485 termination
Set section 6 of the 6-way switch (B) as per the table below to select the termination of the
RS485 twisted pair input. “0” represents OFF (down) and“1” represents ON (up). The default
position in ON (up).
Termination 6
OFF 0
ON 1
The termination switch should be ON if:
•The dome is the only one connected to the twisted pair
•The dome is the last one of several domes connected to the twisted pair
•An alarm module is fitted into the dome power supply
The termination switch should be OFF if:
•More than one dome is connected to the twisted pair and the dome is not the last in
the line.
1.6Replacing the DIP switch cover
•Replace the DIP switch access screw (A) on the rear of the dome
•Take care that the thread is correctly aligned, that there is no dirt or grit that could
affect the waterproof seal.
•Using a large flat bladed screwdriver turn clockwise to secure the screw.
•Do not over-tighten.

Page 12

Page 13
2 Installing the Dome
These installation instructions assume that a standard wall-mount bracket is being used. For
swan-neck, pendant and corner options, refer to their specific instruction sheet.
2.1 Fixing the mounting ring
•Fix the mounting ring to the wall using four screws (A) of adequate size and
strength to support the weight of the dome and bracket.
•Fit the umbilical cable, entering either through the wall or via a cable gland as
illustrated below.

Page 14
2.2 Securing the bracket
•Secure the bracket (B) to the mounting plate (A) using the 4 screws supplied (C)
•For safety reasons, one of the fixing screws must have washer (D) fitted as shown
below.
•Position the umbilical cable (E) such that the connector (F) is above the dome
support cradle (G)

Page 15
2.3 Attaching the CMOR Dome
•Fully loosen the locking ring (C) by rotating clockwise until it nearly touches the top
of the dome
•Lift the dome (taking care not to lift it using lamps) and place the dome support plate
(A) onto the dome support cradle (B). Note that the curved side of the support plate
goes to the back.
•Rotate the locking ring (C) counter-clockwise to lock the dome firmly in position.
2.4 Attaching the umbilical cable
•Plug the waterproof connector on the umbilical cable into the top of the dome
•Turn the locking ring (A) clockwise to secure the connector

Page 16
2.5 Fitting the bracket cover
•Locate the two plastic sides of the cover on the metal support bracket
•Fix together with the supplied screw using the supplied Allen key

Page 17
3 Installing Power Supply
The CMOR-PSU-1 power is supplied in a weatherproof box that may be mounted externally
or internally.
3.1 Fixing power supply to wall
•Fit the optional alarm module (A) into the power supply using the 4 screws provided.
•For safety reasons never remove the slotted metal cover (B).
•Fix the power supply to a wall using a screw in each of the four corner holes (C).

Page 18
3.2 Power Supply Connections
3.2.1 Mains Input
Identification Mains Power
Live Live (brown) 240Vac 50Hz
Neutral Neutral (blue) 240Vac 50Hz
Earth Earth (Yellow/Green)
3.2.2 Connections to dome
Identification Umbilical lead to dome
CAM2 White Coax signal (dual camera version only)
GND White Coax screen (dual camera version only)
CAM1 Black Coax signal
GND Black Coax screen
RS485 (A) WHITE
RS485 (B) ORANGE
+24V RED
0V BLACK and Cable screen

Page 19
3.2.3 Connections to DVR
Identification DVR
CAM2*
GND
Camera input (dual camera version only)
CAM1*
GND
Camera input
RS485 (A) RS485 (A) or (+) dome output
RS485 (B) RS485 (B) or (-) dome output
Spare Not connection
GND RS485 ground
Identification DVR
CAM2 (BNC)* DVR camera input (dual camera version only)
CAM1 (BNC)* DVR camera input
CAM2 (BNC) Loop-through provided for test monitor (dual camera
version only)
CAM1 (BNC) Loop-through provided for test monitor
*Note that the video connection(s) made be made either using the BNC or the screw
terminals, whichever is more convenient.

Page 20
3.3 Alarm Module Connections
3.3.1 Alarm Inputs
Identification Alarm Inputs
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Connect to NO or NC relay
contact of PIRs or other alarm
sources.
3.3.2 Alarm Grounds
All alarms grounds are connected together and any may be used for the relay common
outputs of the PIRs or other alarm sources.
3.3.3 Relay Connections
Identification Alarm Inputs
NO Connect to DVR alarm input if normally open signal is required
COM Connect to DVR alarm input ground
NC Connect to DVR alarm input if normally closed signal is required