VIDEOTRACK VT-DOM372 User manual
Attention
►Do not connect cables when power is on! ►Please use DC 12V, currency no less than 1.5A.
Do not connectcables when poweris on!
DC12V/1.5A
►All uncovered cable should be less than 5mm, to avoid exceptional device damage.
►Network cable quality will influence the communication distance. Please use repeater when exceeding
network communication distance.
123
Uncovered cableshould beless than 5mm
Pleaseuserepeater when exceeding 80m
►When camera is installed outside, please put it in thunder-proof place. Do not touch the camera when
lightning.
►Camera working environment: Temperature -20 ℃～+55 ℃,humidity 10% ～95%RH.
Note: Please pay attention to above notices, otherwise the device can not work normally and
even get damaged seriously.
TCP/IP
①②③④ ⑤
PC
Microphone
Audio input Detective
Alarminput Loudspeaker
Audio input Alarmoutput
Warning lamp Remotedevice
R 485S
①External radio collectors like microphone to realize voice collection function
②External alarm input devices like detector to realize setting up defense function on spot
③External radio play devices like active loudspeaker to realize broadcast function
④External alarm output devices like alarming lamp to realize remote alarm linkage function
⑤Remote controlling camera through PTZ to realize one-in-all surveillance.
Based on TCP/IP network, it is convenient to manage and control terminal devices.
Notes: ①Please refer to user manual for details concerning cable interface.
②For other information not mentioned here, please read related user manual.
Wall mount installation method:
②③
④
⑤
①Affix the paper template to the wall and drill holes according to the marked circles in the paper
template.
②Affix the pedestal to the wall by 4 screws.
③Hang the camera in the pedestal and tighten the 4 screws, to fix the camera in related pedestal..
④Take off the transparent cover from camera by screwdriver, and adjust the lens angle to appropriate
surveillance area.
⑤Tighten the screws to fix the transparent cover.
Chapter 2: How to install IP camera
Chapter 1: Diagram for IP camera video surveillance
IR Vandal-proof Dome IPC Installation Guide
Version：1.0 Date：October, 2011
①
Wall mount installation paper template
www.VideoTrack.us
www.VideoTrack.us
Ceiling mount installation method:
①Affix the paper template to the ceiling and drill holes according to the marked circles in the paper
template.
②Affix the camera and pedestal to the ceiling by 3 screws.
③Adjust the lens angle to appropriate surveillance area.
④Tighten the screws to fix the transparent cover.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1. Power supply: Connect with power adaptor
2. RJ.45: Ethernet port for 10/100M. Through this port, you can connect the camera with other network
devices like switcher, hub, router, etc.
3. Reset button: Long press this button for more than 30 seconds when power on, the camera will
recover to default configuration. Default IP address is 192.168.1.88, user name “admin” and password
“admin”.
4. Alarm: Connect with external alarm input & output devices. See below detailed information.
Note: Different alarm input device should use different software configuration. Please refer to the user
manual for details.
IN
123 4 5
NC
COM
NO
GND
Alarminput
Alarmoutput
123
485+
485-
GND
Picture 1 Picture 2
5. RS485: Supports standard 485 PTZ protocols, for remote device control. Please see above picture 2.
6. Audio input: Connects with external voice collectors like microphone to realize voice collection function.
7. Audio output: Connects with external play devices like act loudspeaker to realize broadcast function.
8. Analog video output: For project adjustment use on spot. Please refer to related user manual for
details.
For the first network conection, please follow the sollowing steps to configur your nectwork.
1. Use cable to connect camera with computer.
2. When connecting with 10M network, the orange indicator will be on, when connecting with 100M
network, the green indicator will also be on.
3. If your computer IP address is in different gateway with that of camera, please change your computer
IP address in the same gateway as camera, for example, 192.168.1.87.
4. In the IE browser, please input camera IP address (default IP “192.168.1.88”) and enter, then below
dialog table will come out.
Picture 3 Picture 4
5. After input the user name and password (default user name “admin” and password “admin”), below
activeX controls will show in the screen. This is a prerequisite activeX and controls for this application,
without any danger information. Please run it according to above picture 4.
6. After finish the activeX and controls installation, please refresh the web page and below picture will
come out.
7. If you want to change the camera IP address, please refer to the user manual.
Note: Please adjust the IP address well first and then install the camera.
Chapter 4: Network connection
Chapter 3: Introduction on cable interface
②
④
③
Ceiling mount installation paper template
①
www.VideoTrack.us
www.VideoTrack.us
