Vigon MP-955IR-WM User manual

Vicon part number 8009-8194-68-01 Section 3 Rev 1009
XX194-68-01
MP-955IR-WM WALL MOUNT OPTION
FOR MP-955IR BULLET CAMERA
Copyright © 2009 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: [phone] WEB: www.vicon-cctv.com

XX194-68-00 Rev 909 MP-955IR-WM Introduction •1
Introduction
The information in this instruction manual covers the installation of the MP-955IR-WM Wall Mount for the MP-
955IR Bullet Camera. This mount should only be installed by a qualified technician using approved materials
and wiring practices in accordance with the National Electrical Code ANSI/NFPA 70, state, and local electrical
codes. Read these instructions thoroughly before beginning an installation.
The MP-955IR-WM is used when installation requires wall-mount configurations. The mount allows moving
the camera both horizontally (pan) and vertically (tilt). The accessory kit contains all necessary hardware for
installation.
Installation
Installation Preparation
Cabling should be run to the installation site before the mount is installed. Refer to instruction manual XX194-
1X for complete instructions on camera installation, wiring and adjustment.
Note: Verify that the selected mounting location is free of obstacles such as wiring or pipes.
Caution: Mount these units only to structural materials with sufficient strength to carry the overall weight of
the mount and unit.
Wall-Mount Installation
The MP-955IR-WM is used when the MP-955IR is to be installed onto a wall or ceiling. The wall mount
includes hardware necessary for installation.
1. Using the wall mount as a template, mark the location of the four (4) mounting holes; two of the holes are
slotted. Drill holes at these locations and insert the anchors provided.
2. If not already done, route all necessary cables to the installation location.
3. Route the cables through the cable access hole in the wall mount
4. Secure the mount to the wall with the screws provided.
5. Install the camera onto the mount, aligning the mounting holes on the bottom of the camera with the slots
on the mount head.
6. Loosen the screws to allow adjustment of position (pan and tilt). Retighten screws when finished.
7. Follow the directions in the camera manual to make all necessary cable connections.
Completed Installation
Mounting Holes
(4X)
Cable Access
Hole
Loosen Screws
to Adjust Pan/Tilt
Position

2 •Shipping Instructions XX194-68-00 Rev 909 MP-955IR-WM
Shipping Instructions
Use the following procedure when returning a unit to the factory:
1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name
of the Vicon employee who issued the R.A.
Vicon Industries Inc.
89 Arkay Drive
Hauppauge, NY 11788
Phone: 631-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV (2288)
For service or returns from countries in Europe, contact:
Vicon Industries (U.K.) Ltd
Brunel Way
Fareham, PO15 5TX
United Kingdom
Phone: [phone]; Fax: [phone]
2. Attach a sheet of paper to the unit with the following information:
a. Name and address of the company returning the unit
b. Name of the Vicon employee who issued the R.A.
c. R. A. number
d. Brief description of the installation
e. Complete description of the problem and circumstances under which it occurs
f. Unit’s original date of purchase, if still under warranty
3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.
4. Mark the R.A. number on the outside of the carton on the shipping label.

XX194-68-00 Rev 909 MP-955IR-WM Technical Information •3
Technical Information
MECHANICAL
Application: Outdoor.
Dimensions: See Figure below.
Mounting: Wall/ceiling.
Construction: Aluminum alloy; silver finish.
Dimensional Drawing

4 •Vicon Standard Equipment Warranty XX194-68-00 Rev 909 MP-955IR-WM
Vicon Standard Equipment Warranty
Vicon Industries Inc. (the “Company”) warrants your equipment to be free from defects in material and workmanship under
Normal Use from the date of original retail purchase for a period of three years, with the following exceptions:
1. VCRs, all models: Labor and video heads warranted for 120 days from date of original retail purchase. All other
parts warranted for one year from date of original retail purchase.
2. Video monitor CRT (cathode ray tube) and LCD monitors, all models: One year from date of original retail
purchase.
3. Uninterruptible Power Supplies: Two years from date of original retail purchase.
4. VDR-408 and VDR-416 Recorder Series: One year from date of original retail purchase.
5. V5616MUX: One year from date of original retail purchase.
6. S10-CH: 18 months from date of original retail purchase.
7. Normal Use excludes prolonged use of lens and pan-and-tilt motors, gear heads, and gears due to continuous
use of “autopan” or “tour” modes of operation. Such continuous operation is outside the scope of this warranty.
8. Vicon Security Management Systems (SMS) All Models: All hardware is warranted for two years from date of
original retail purchase.
9. Any product sold as “special” or not listed in Vicon’s commercial price list: One year from date of original retail
purchase.
Date of retail purchase is the date original end-user takes possession of the equipment, or, at the sole discretion of the
Company, the date the equipment first becomes operational by the original end-user.
The sole remedy under this Warranty is that defective equipment be repaired or (at the Company’s option) replaced, at
Company repair centers, provided the equipment has been authorized for return by the Company, and the return shipment
is prepaid in accordance with policy.
The Company will not be obligated to repair or replace equipment showing abuse or damage, or to parts which in the
judgment of the Company are not defective, or any equipment which may have been tampered with, altered, misused, or
been subject to unauthorized repair.
Software supplied either separately or in hardware is furnished on an “As Is” basis. Vicon does not warrant that
such software shall be error (bug) free. Software support via telephone, if provided at no cost, may be
discontinued at any time without notice at Vicon’s sole discretion. Vicon reserves the right to make changes to
its software in any of its products at any time and without notice.
This Warranty is in lieu of all other conditions and warranties express or implied as to the Goods, including any
warranty of merchantability or fitness and the remedy specified in this Warranty is in lieu of all other remedies
available to the Purchaser.
No one is authorized to assume any liability on behalf of the Company, or impose any obligations on it in connection with
the sale of any Goods, other than that which is specified above. In no event will the Company be liable for indirect, special,
incidental, consequential, or other damages, whether arising from interrupted equipment operation, loss of data,
replacement of equipment or software, costs or repairs undertaken by the Purchaser, or other causes.
This warranty applies to all sales made by the Company or its dealers and shall be governed by the laws of New York
State without regard to its conflict of laws principles. This Warranty shall be enforceable against the Company only in the
courts located in the State of New York.
The form of this Warranty is effective August 1, 2009.
THE TERMS OF THIS WARRANTY APPLY ONLY TO SALES MADE WHILE THIS WARRANTY IS IN EFFECT. THIS
WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE
COMPANY’S WEBSITE, WWW.VICON-CCTV.COM. IN THAT EVENT, THE TERMS OF THE POSTED WARRANTY
SHALL APPLY EXCLUSIVELY.
Vicon Part Number: 8006-9010-03-07 Rev 809

XX194-68-00 Rev 909 MP-955IR-WM Vicon Standard Equipment Warranty •5
Notes

Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
Vicon Europe
Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
[phone]
Fax: [phone]
Germany
vin-videotronic infosystems gmbh
Lahnstrasse 1
D-24539 Neumuenster
Phone: [phone]
Fax: [phone]
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: [phone]
Internet Address: www.vicon-cctv.com