Eagle Group QuadPLUS Polymer User manual

ASSEMBLY INSTRUCTIONS
QuadPLUS®Polymer Dunnage Rack
&5*2&%
"(+&..%2&15*$&04*/,&-3"(+&/&$7"-%&3"*+*2/+"6"1&%*5*2*.-2.'"(+&1.4/8#63)&"(+&1.4/
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: [phone] • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637- 100
• Fax: [phone]
CAUTION
! !
SAVE YOUR BOX AND ALL PACKING MATERIALS.
!!!


BEFORE ASSEMBLY, PLEASE READ:
It is recommended to assemble truss frames and/or shelves onto posts—and to secure frame and/or shelf by tapping
with a mallet—BEFORE installing polymer mats. IMPORTANT: DO NOT HIT TRUSS FRAMES AND/OR SHELVES AFTER
POLYMER MATS HAVE BEEN INSTALLED! Remove polymer mats before readjusting truss frame.
(continued on back age)
Thank you for your purchase. Before assembly, read this instruction sheet carefully to ensure correct use.
After reading, be sure to store this instruction sheet in a safe place, should it be needed for future reference.
Stationary Units Mobile Units
1.Assemble 3-sided frame to osts.
A. Snap plastic tapered split sleeves onto each post at the desired
position for the 3-sided frame (see Figure 1a).
Note: Although the 3-sided frame should be mounted as low as
possible for the most stability, NSF requires a minimum of 6˝
clearance below the frame. For NSF-approved installation, mount
frame at the 6th groove or above on each post.
B. Holding the 3-sided frame on its side, insert the posts through the
corner collars until the split sleeves are seated snugly within the
collars (see Figure 1b).
IF YOU ORDERED A MOBILE UNIT, AFFIX CASTERS TO POSTS…
A. Place donut bumper onto bottom end of each post (see Figure 1c).
B. Insert caster stem into bottom of each post. Drive in caster using a
hammer or mallet (see Figure 1d).
Figure 1a
Figure 1b
split sleeves
3-sided
frame
post
post
corner collar
Figure 1c
caster
post
caster
stem
bumper
Figure 1d

"(+&..%2&15*$&04*/,&-3"(+&/&$7"-%&3"*+*2/+"6"1&%*5*2*.-2.'"(+&1.4/8#63)&"(+&1.4/
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: [phone] • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637- 100
• Fax: [phone]
ASSEMBLY INSTRUCTIONS
QuadPLUS®Polymer Dunnage Rack
(End)
IMPORTANT!
Figure 2b
3-sided
frame
post
wire shelf
Figure 2c
Figure 3a
QuadPLUS®shelf mats
2.Attach wire shelf to ost/frame assembly.
A. Stand the post/frame assembly upright, and snap the
split sleeves onto each post at the topmost groove (see
Figure 2a).
B. Mount the wire shelf, inserting the posts through the
corner collars of shelf (see Figure 2b) until the split
sleeves are seated snugly within the collars.
C. Securely seat wire shelf using a board and hammer at
each corner (see Figure 2c).
3.Attach QuadPLUS®shelf mats.
A. Position polymer mats onto wire shelf accordingly (see
Figure 3a).
B. Gently push each mat down along the front and rear to
snap them into place.
Assembly is complete.
notch in
end mat
notch in end mat
Note:
Notches
indicate
end mats.
Figure 2a
post split sleeves