Viking VMDD5306SS User manual

1E
Installation Guide
Convection/Speed
Microwave Oven
VMDD5306SS

2
E
ENGLISH
IMPORTANT–Please Read and Follow!
• Before beginning, read these instructions thoroughly
and carefully.
• Because the kit includes metal parts, caution should
be used in handling and installation to avoid the pos-
sibility of injury.
• Do not remove permanently affixed labels, warnings or
plates from the product as this may void the warranty.
• Observe all local and national codes, requirements
and ordinances.
• Installers should leave these instructions with the con-
sumer who should retain them for the local inspector’s
use and for future reference.
ELECTRICAL GROUNDING INSTRUCTIONS
This oven must be electrically grounded in
accordance with local codes or, in the absence
of local codes, with the National Electrical Code,
ANSI/NFPA 70 – latest edition.
DO NOT USE AN EXTENSION CORD
WITH THIS APPLIANCE. SUCH USE MAY RESULT
IN FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
IMPORTANT SAFETY
INSTRUCTIONS
• WARNING: If the information in this manual is not
followed exactly, a fire or electrical shock may result
that could cause property damage, personal injury
or death.
• This appliance must be electrically grounded in ac-
cordance with local codes.
• Make sure the wall coverings and the cabinets around
the oven can withstand the heat generated by the
appliance.
• WARNING: Never leave children alone or unattended
in the area where a appliance is in use.
• Do not use the oven as a storage space. This creates
a potentially hazardous situation.

3E
ENGLISH
Unpacking your oven
• Remove all packing materials from inside the oven.
• Check the oven for any damage, such as misaligned or
bent oven, damaged oven seals and sealing surfaces
or dents inside the cavity or on the front side of the
oven. If there is any damage, do not operate the oven
and contact your AUTHORIZED SERVICER.
Important Notes to the
Installer
• Read all of the Installation Guide before installing
the oven.
• Remove all packing material before connecting the
electrical supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
Important Notes to the
Consumer
Keep this manual with your Use and Care Manual for
future reference.
• As when using any oven generating heat, there are
certain safety precautions you should follow. These
are listed in the Use and Care Manual. Read all and
follow carefully.
• Be sure your oven is installed and grounded properly
by a qualified installer or service technician.
Choosing a Location
Your oven can be built into a cabinet or wall by itself,
above any electric wall oven, warming drawer or below
a cooktop or counter.
Electrical Requirements
Located the electrical supply as shown in the illustrations
on the following pages. The receptacle may also be lo-
cated in an adjacent cabinet within reach of the power
cord. A separate circuit, servicing only the appliance is
required. A ground fault circuit interrupter (GFCI) is not
recommended and may cause interruption of operation.
Electrical Supply 220-240 V AC, 50 Hz
Service 2800 W
Power Cord 47-1/4"
Note:
• If you have any questions about the grounding or
electrical instructions, consult a qualified electrician
or service person.
• Can also be installed using an electrical outlet in an
adjacent cabinet within the area where the provided
electrical cord can reach.
• Always check electrical codes for requirements.
GROUNDING
INSTRUCTIONS
This appliance must be grounded. The oven is equipped
with a cord having a grounding wire with a grounding
plug. It must be plugged into a wall receptacle that is
properly installed and grounded in accordance with the
National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding re-
duces risk of electric shock by providing an escape wire
for the electric current.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Do not use an exten-
sion cord. If the power supply cord is too short, have
a qualified electrician or serviceman install an outlet
near the appliance.

4
E
ENGLISH
Installation Hardware
Oven Measurements
NAME QTY PART CODE
Mounting Screws 4 LANGTB407MRP0
29-1/2”
(749.4 mm) 4-3/16”
(106.9 mm)
21-1/4” (540.1 mm)
BEHIND FRAME
17-1/2”
(446.0 mm)
17-7/8”
(454.0 mm)
1-29/32”
(48.8 mm)
21-3/16”
(538.0 mm)
14-3/16”
(360.0 mm)
OPEN
OVEN DOOR
Figure 1

5E
ENGLISH
Clearances and Dimensions for Standard Surface Mount
A. 22 1/4" cutout
B. 17 5/8" cutout
C. 23 1/2" min. depth
Note: Platform
must be able to
support 125 lbs.
Allow
3
5
/8"
overlap
Allow
3
/8"
overlap
Allow
3
5
/8"
overlap
Figure 2