Viking Designer DMOS200SS User manual

VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
[phone]
PARTS INCLUDED IN THE KIT
5) Template: QTY 1
Minimum Cutout Opening Width 24 3/8" (619.13 mm)
Maximum Cutout Opening Width 24 11/16" (627.06 mm)
14 5/16" (363.475 mm)
Minimum Cutout Opening Height 16 3/4" (425.5 mm)
Maximum Cutout Opening Height 17" (431.8 mm)
12 13/16" (325.4 mm)
Distance between holes 25 5/8" (650.75 mm)
Distance between holes 28 5/8" (727.3 mm)
15 29/32" (403.66 mm)
29/32" (23.4 mm)
Center Line
Floor Line of Cutout Opening
BUILT-IN TRIM KIT TEMPLATE
FOR DESIGNER SERIES MICROWAVE OVEN
1. Align the mounting templatecenter line with the center of
the cutout and the floor line with the floor of the cutout.
Tapeit into place.
2. ForDMTK271, predrill 4 holes marked with a HP"drill bit.
ForDMTK301, predrill 4 holes marked with a HP"drill bit.
3. Removetemplate from the cabinet
TINSKB110MRR0
1) Frame Assembly
Front Frame
QTY 1
Back Frame
QTY 1
2) Bottom Duct Assembly: QTY 1
3) Screw A (1-3/16" length): QTY 2 4) Screw B (1 3/4" length): QTY 4
NOTE:
SIDE FLANGES ON
DMTK301 ONLY.
INSTALLATION
INSTRUCTIONS
DESIGNER SERIES
MICROWAVE BUILT-IN TRIM KIT
Retain for Future Reference
IMPORTANT - PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.
Remove the turntable from the oven cavity.
• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future
reference.
THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING MICROWAVE OVENS SPECIFYING BUILT-IN
TRIM KIT DMTK271 OR DMTK301 ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE OVEN CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.

C
B
A
4"(10.2 cm)
4"(10.2 cm)
6"(15.2 cm)
SCREW A
BOTTOM
DUCT ASSEMBLY
MAKE FLANGES
FLUSH
Illustration 1
Illustration 2
Illustration 3
NOTE:
SIDE FLANGES ON
DMTK301 ONLY.
2
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as indicated
on Illustration 1.
NOTE 1: If the Depth (C) dimension is greater than 21"
(53.3 cm), the outlet location may be in any area on the
rear wall.
NOTE 2: The floor of the opening should be constructed
of plywood strong enough to support the weight of the
oven and floor load (approximately 100 pounds). The
floor should be level for proper operation of the oven.
Be sure to check the local building code as it may require
that the opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven does not
require the enclosure.
MOUNTING TEMPLATE
1. Align the mounting template center line with the center
of the cutout and the floor line with the floor of the
cutout. Tape it into place.
2. For DMTK271, only predrill 4 holes marked “A” with
a 1/16" drill bit. For DMTK301, only predrill 4 holes
marked “B” with a 1/16" drill bit.
3. Remove template from the cabinet
BOTTOM DUCT ASSEMBLY
1. Place the Bottom duct in the opening. When the Bottom
Duct Assembly is in the opening correctly, the flanges
will be tightly against the lower edge of the opening.
See Illustration 2.
2. Secure the Bottom Duct Assembly with the two (1-3/16")
screws A. See Illustration 2.
CABINET OR WALL CUTOUT
Cutout Dimensions
Height (A) Minimum 16 3/4" (42.5 cm)
Maximum 17" (43.2 cm)
Width (B) Minimum 24 3/8" (61.9 cm)
Maximum 24 11/16" (62.7 cm)
Depth (C) Minimum 20" (50.8 cm)

Illustration 4
Illustration 6
2" (5.1 cm) For 27" W
and 30" W lower oven
Illustration 7
Illustration 5
SCREW B
SCREW B
SCREW B
SCREW B
SNAP ATTACHMENT
BOTTOM DUCT
ASSEMBLY
FOOT
DUCT RECESS
TABS
3
Position the BACK FRAME to align with the predrilled
holes that were drilled with the mounting template. Check
that it is level and then secure with four SCREWS B. See
Illustration 5.
Place the FRONT FRAME, with tabs on top, onto the
BACK FRAME. Secure the FRONT FRAME to the BACK
FRAME by firmly pushing the front frame onto the back
frame engaging the four (4) snap attachments. See
illustration 6.
FRAME INSTALLATION
OVER OVEN INSTALLATION
See illustration 7.
CABINET INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening.
Plug the power cord into the electrical outlet.
2. Carefully guide the assembled oven into the prepared
opening. Slide the oven on the Bottom Duct Assembly.
See Illustration 3. Avoid pinching the cord between the
oven and the wall. Adjust the position of the oven so
that the feet of the oven are fitted into the recesses of
the Bottom Duct Assembly. See Illustration 4.

Microwave Oven Built-In Trim Kits
DMOS200 DMTK271 DMTK301
Overall Width 24” (60.9 cm) 26-1/2” (67.3 cm) 29-1/2” (74.9 cm)
Overall Height from Bottom 13-3/8” (33.9 cm) 18-1/4” (46.3 cm) 18-1/4” (46.3 cm)
Overall Depth from Rear 19-1/4” (48.9 cm) N/A
Oven Interior Width
Height
Depth
Overall
17-3/8”
10-1/2”
18-5/8”
2.0 cu. ft.
(44.1 cm)
(26.6 cm)
(47.3 cm)
N/A
Cutout Width N/A Min.
Max.
24-3/8”
24-11/16"
(61.9 cm)
(62.7 cm)
Cutout Height N/A Min.
Max.
16-3/4”
17"
(42.5 cm)
(43.2 cm)
Cutout Depth N/A Min. 20” (50.3 cm)
Electrical Requirements 120VAC/60 Hz N/A
Max. Amp Usage 1.5 KW 13 amps N/A
Approx. Shipping Wt. 46 lbs. (20.9 kg) 14 lbs. (6.5 kg) 15 lbs. (6.9 kg)
Viking Range Corporation
111 Front Street • Greenwood, Mississippi (MS) 38930 USA • [phone]
Specifications subject to change without notice.
For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com
F20195B (PS0506VR)
TINSEB466MRR0
BASIC SPECIFICATIONS