VIKTRA BENTE III 28 User manual

BENTE III 28
× 55
× 10
× 12
× 370
× 30
× 30
4×405×70
4×506×1401,4×40
M8×60
Ø 3 mm
Ø 4 mm
Ø 5 mm
Ø 8 mm
1/19
PREPARE THE GROUND, UNWRAP THE PACKAGE,
LAY OUT THE COMPONENTS, FIND THE TOOLS.

BENTE III 28
2/19
MAKE SURE THAT THE FOUNDATION
IS INSTALLED ON A LEVEL SURFACE.
CHECKING ALL DIRECTIONS,
INCLUDING CORNER TO CORNER. 3%
LAY OUT THE FOUNDATION BEAMS
AND SQUARE IT BY MEASURING
FROM CORNER TO CORNER.
IFB
AC
DB
AB=CD
0°

BENTE III 28
× 5× 12
5×70
6×140
Ø 4 mm
Ø 5 mm
3/19
LAY OUT THE BOTTOM LOGS,
ATTACH TO THE FOUNDATION.
THE WALL LOGS WILL HANG OVER
THE FOUNDATION BEAMS BY
APPROXIMATELY 5MM. THIS OVERHANG
IS DESIGNED AS A RAIN DRIP. 5%
2 BL-1
6×140
1 BL-1
1 BL-1
A LG-1
B LG-1
5×70
5mm

BENTE III 28
× 4
5×70Ø 4 mm
× 5
6×140Ø 5 mm
4/19 7%
ATTACH THE FIRST ROW OF
WALL LOGS INTO THE BOTTOM
LOGS WITH SCREWS.
2 LG-5
1 LG-1
1 LG-1
6×140
5×70

BENTE III 28
5/19 12%
AFTER PLACING 3-4 ROWS OF WALL LOGS, TAP EACH
WALL LOG IN PLACE USING A HAMMER AND THE
HITBLOCK PROVIDED, TO TIGHTEN THE LOGS.
HITBLOCK

BENTE III 28
6/19 13%
SLIDE THE DOOR IN,
ATTACH THE HANDLE.
BDD3
3 LOGS IN PLACE

BENTE III 28
7/19 26%
DON`T FORGET TO
TIGHTEN THE LOGS AFTER
EVERY 3-4 ROWS.

BENTE III 28
× 4
6×140Ø 5 mm
8/19 42%
INSTALL THE GABLES WITH LONG SCREWS
TO THE WALL LOGS ON THE FRONT AND
REAR WALLS.
15 LOGS IN PLACE
GABLE
B TL-1
A TL-1

BENTE III 28
× 6
6×140Ø 5 mm
9/19 43%
INSTALL THE ROOF PURLINS AND
ATTACH THEM WITH SCREWS.
RFR
RFB
RFB

BENTE III 28
× 186
4×50
10/19 46%
PLACE THE FIRST ROOFBOARD FLUSH WITH
THE END OF THE PURLINS AND ATTACH
WITH 6 SCREWS, 3 INTO EACH NEXT,
SAW THE LAST BOARD TO MAKE IT FIT.
RB

BENTE III 28
× 28
4×40
11/19 79%
INSERT FOR THE FASCIA TRIMS
SCREWS AFTER EVERY 0,5 METERS.
RR1
RR2

BENTE III 28
× 28
4×40Ø 3 mm
12/19 83%
EAVES EDGES GO ON TOP
OF THE ROOFING*.
*(NOT INCLUDED) RF EE

BENTE III 28
×4
4×40Ø 3 mm
13/19 84%
ATTACH ROMBS WITH SCREWS.
ROMB

BENTE III 28
× 162
4×50
14/19 89%
16 SCREWS INTO THE FIRST FLOORBOARD,
8 INTO EACH NEXT, SAW THE
LAST BOARD TO MAKE IT FIT.
FB

BENTE III 28
× 30
1,4×40
15/19 96%
SAW THE BASEBOARDS
AND ATTACH WITH NAILS
AT EVERY 0,5 METERS.
BB

BENTE III 28
× 12
M8×60
M
8
×
60
Ø 8 mm
16/19 97%
DRILL THROUGH THE WALL, HOLE MUST
BE AT THE BOTTOM OF THE OVAL,
ATTACH WITH BOLT.
4CM
20CM
WINDBOARD

BENTE III 28
90º
90º
17/19 98%
IF DOOR IS TILTED,
PUSH THE DOOR FRAME SO
THAT ALL CORNERS ARE 90º.

BENTE III 28
18/19 99%
IF DOORS ARE IN DIFFERENT HEIGHTS
OR THERE IS A GAP BETWEEN THEM,
ADJUST 3 SCREWS ON DOOR HINGES.

BENTE III 28
19/19
WHEN THE HOUSE IS ASSEMBLED, YOU SHOULD
COVER THE TIMBER WITH WOOD PROTECTIVE SEAL,
PAINT OR STAIN AS SOON AS POSSIBLE TO AVOID
DETERIORATION TO THE WOOD.
100%