Visa Lighting CB5513 User manual

SHINE
CB / OW5513
CB / OW 5515
CB / OW 5517
CB / OW 5524
Drawing:
762250XX
Rev:
B
Sheet:
1 of 5
Eng:
SLN
Date Drawn:
10/14/15
INSTALLATION INSTRUCTIONS
Model: CB5513 / 5515 / 5517 / 5524, OW5513 / 5515 / 5517 / 5524
Fixture Family: SHINE (LED)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
SHINE Series Luminaires

DAMP LOCATION INSTALLATION
MAIN
LENS
INNER LED
LENS
LAMP PLATE
MOUNTING
SCREWS (2)
LED LAMP
PLATE
MOUNTING SCREWS
(SUPPLIED BY OTHERS)
HOUSING
JUNCTION
BOX
MOUNTING
SURFACE
1 Slide off main lens by pulling forward.
2. Remove inner LED lens by gently squeezing top and bottom and pulling away from LED lamp plate.
3. Remove LED lamp plate by unscrewing (2) lamp plate mounting screws.
4. Feed electrical wires through wire access hole in housing.
5. WHILE CHECKING FOR LEVEL, secure housing to wall with screws (supplied by others).
6. Make electrical connections per code.
7. Resecure LED lamp plate with provided lamp plate mounting screws (2).
8. Resecure inner LED lens and gently reinstall main lens.
Drawing:
762250XX
Rev:
B
Sheet:
2 of 5
Eng:
SLN
Date Drawn:
10/14/15
INSTALLATION INSTRUCTIONS
Model: CB5513, CB5515, CB5517 & CB5524
Fixture Family: SHINE (LED)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
SHINE Series Luminaires

AUXILARY
MOUNTING SCREWS
(SUPPLIED BY OTHERS)
LED LAMP
PLATE
MOUNTING
SURFACE
JUNCTION
BOX
HOUSING LAMP PLATE
MOUNTING
SCREWS (2)
INNER LED
LENS
MAIN
LENS
DAMP LOCATION INSTALLATION
WITH JUNCTION BOX COVER PLATE
(JBC OPTION)
1 Slide off main lens by pulling forward.
2. Remove inner LED lens by gently squeezing top and bottom and pulling away from LED lamp plate.
3. Remove LED lamp plate by unscrewing (2) lamp plate mounting screws.
4. Feed electrical wires through wire access hole in housing.
5. WHILE CHECKING FOR LEVEL, secure housing to wall with screws (supplied by others).
6. Make electrical connections per code.
7. Resecure LED lamp plate with provided lamp plate mounting screws (2).
8. Resecure inner LED lens and gently reinstall main lens.
Drawing:
762250XX
Rev:
B
Sheet:
3 of 5
Eng:
SLN
Date Drawn:
10/14/15
INSTALLATION INSTRUCTIONS
Model: CB5513, CB5515, CB5517 & CB5524
Fixture Family: SHINE (LED)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
SHINE Series Luminaires

MAIN
LENS
INNER LED
LENS
LAMP PLATE
MOUNTING
SCREW (2)
LED LAMP
PLATE
LENS
HOLD DOWN
PLATE (2)
HOUSING
W/ GASKETS
LENS HOLD DOWN
FLAT HEAD SCREWS
MOUNTING
SURFACE
WET LOCATION INSTALLATION
JUNCTION
BOX
MOUNTING
FASTENERS
(BY OTHERS)
1 Remove lens hold down plates (2).
2. Slide off main lens by pulling forward (Caution - take care not to rip gasket on housing at perimeter of lens opening).
3. Remove inner LED lens by gently squeezing top and bottom and pulling away from LED lamp plate.
4. Remove LED lamp plate by unscrewing (2) lamp plate mounting screws.
5. Feed electrical wires through wire access hole in housing.
6. WHILE CHECKING FOR LEVEL, secure housing to wall with screws (supplied by others)
NOTE: If wall is not smooth, secure a bead of silicone around perimeter of fixture.
7. Make electrical connections per code.
8 Resecure LED lamp plate with provided lamp plate mounting screws (2).
9. Resecure inner LED lens and gently reinstall main lens. (taking caution not to rip gasket while sliding it back on)
10. Reattach lens hold down plates (2) with provided flat head screws. (quantity of screws will vary depending on
fixture length)
Drawing:
762250XX
Rev:
B
Sheet:
4 of 5
Eng:
SLN
Date Drawn:
10/14/15
INSTALLATION INSTRUCTIONS
Model: OW5513, OW5515, OW5517 & OW5524
Fixture Family: SHINE (LED)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
SHINE Series Luminaires

MAIN
LENS
INNER LED
LENS
LAMP PLATE
MOUNTING
SCREWS (2)
LED LAMP
PLATE
JBC MOUNTING
#8 KEPS NUTS (4)
HOUSING
W/ GASKETS
LENS
HOLD DOWN
PLATE (2)
LENS HOLD DOWN
FLAT HEAD SCREWS
JUNCTION BOX
COVER PLATE
JUNCTION
BOX
MOUNTING SURFACE
WET LOCATION INSTALLATION
WITH JUNCTION BOX COVER PLATE
(JBC OPTION)
1 Remove lens hold down plates (2).
2. Slide off main lens by pulling forward (Caution take care not to rip gasket at perimeter of lens opening).
3. Remove inner LED lens by gently squeezing top and bottom and pulling away from LED lamp plate.
4. Remove LED lamp plate by unscrewing (2) lamp plate mounting screws.
5. Remove junction box cover plate from housing by loosening and removing junction box #8 keps nuts.
6. Feed electrical wires through junction box wire access hole in housing.
7. WHILE CHECKING FOR LEVEL, secure junction box cover plate to wall with screws (supplied by others)
NOTE: If wall is not smooth, secure a bead of silicone around perimeter of junction box cover plate.
8. Resecure junction box cover plate to housing with provided #8 keps nuts.
9. Make electrical connections per code.
10. Resecure LED lamp plate with provided lamp plate mounting screws (2).
11. Resecure inner LED lens and gently reinstall main lens. (taking caution not to rip gasket while sliding it back on)
12. Reattach lens hold down plates (2) with provided flat head screws. (quantity of screws will vary depending on
fixture length)
Drawing:
762250XX
Rev:
B
Sheet:
5 of 5
Eng:
SLN
Date Drawn:
10/14/15
INSTALLATION INSTRUCTIONS
Model: OW5513, OW5515, OW5517 & OW5524
Fixture Family: SHINE (LED)
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
Read all instructions carefully before installing and save for future use. •
Make sure all connections are in accordance with the National Electrical Code and local regulations. •
To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture •
Service should be performed by qualified personnel. •
These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. •
Document Description: Installation Instructions for
SHINE Series Luminaires