Vision3 Lighting PA7 User manual

- Page 1 -
Installation Instructions
©2005-2016 Vision3 Lighting™ P.O. Box 607, Fowler, CA 93625 [phone] [phone] fax www.vision3lighting.com
revision 5/12/16
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
(Failure to follow the warnings and instructions on this sheet could result in re, injury, failure of product, and/or voiding of warranty.)
MR16 Bollard Path Light MODEL PA7
12-24 Volt AC/DC, 10 Watt, LED
12 Volt, 50 Watt Max., MR16 Halogen
1. Do not touch luminaire while lamp is on. Turn off/unplug and allow to cool
before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch hot lens, faceplate, cover, or body.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from your skin may
damage lamp.
6. Do not operate with damaged or missing parts.
7. Do not disassemble beyond cover/faceplate and cap removal to facilitate lamp
and/or accessory installation or replacement.
8. Remove any debris accumulated in the cap periodically.
9. Do not install within 10 feet of a pool, spa, or fountain.
10. Have installed in accordance with all applicable installation codes and
standards by a person familiar with the construction, operation, and hazards
involved.
11. Use only cable properly rated for the application. Cable buried more than 6”
must be suitable for direct burial. Direct burial cable may be ordered from
Vision3 Lighting.
Notes:
• This xture requires a remote transformer.
• LED models should only be powered by a magnetic transformer or Vision3
Lighting approved electronic transformer. Contact Vision3 Lighting for
further information.
• LED module requires up to 13W at startup, which must be allowed for when
designing system.
• LED may come with High/Low switch (10W/6.7W @ 12VAC). See ‘LED
Switching’ instructions on next page. Switch, if any, will be set to ‘High’
setting at the factory, unless otherwise specied when ordered.
• LED ratings subject to change without notice. See website or contact V3 for
most current info.
Installation:
1. Unpack the PA7 Bollard Path Light from its shipping container.
2. Check to make sure that there are no damaged or missing components.
3. Loosen, but don’t remove, the four Body Mount Screw’s using a 1/8” hex
tool.
4. Remove the Body from the Mount Base.
5. At the desired location, prepare an appropriate size hole in the ground (if
using a Stake Mount Base) or create the proper mount hole pattern on the
surface (if using a surface mount base).
6. Run appropriate power supply cable (not supplied) to the xture.
7. Feed the power supply cable through the bottom of the Stake, if used, and
the Mount Base.
8. Secure the Mount Base by lling in the hole (if using the Stake Mount
Base) or by installing and tightening the mount screws (if using the
Surface Mount Base. Mount screws not supplied).
9. Connect the socket leads from the Body to the power supply cable using
the appropriate connectors per applicable codes. Vision3 recommends
using water tight wire nuts suitable for in-grade applications.
10. Push the connectors and as much of the wiring as possible down in to
the stake or cable hole to keep it protected.
11. Slide the Body over the Mount Base and on to the Body Mount Screws,
being careful to not pinch or cut any of the wiring.
12. Tighten the four Body Mount Screw’s using a 1/8” hex tool.
13. Install any required lamp or accessories as described below.
Caution! Fixture will be hot if lamp is on. Remove power and allow xture to
cool before performing any adjustments or maintenance.
Lamp Maintenance:
1. Remove power from xture and let cool before touching. Caution!
Luminaire may still be hot!
2. Loosen the Cover Set Screws (3X) using a 3/32” hex tool (do not
remove screws) and remove the Cover from the Faceplate. Note: Not all
xtures have the cover option. In this case, skip this step.
3. Loosen the Faceplate Screws (2X) with a 1/8” Hex tool and remove the
Faceplate Assembly from the Body. Note: Be careful with the socket
leads when removing the Faceplate Assembly.
4. Loosen the Faceplate Set Screw using a 3/32” hex tool – do not remove
screw!
5. Remove the Socket Mount Assembly from the Faceplate Assembly.
6. Replace lamp/LED.
For MR16 Halogen Lamp:
a. Pull lamp straight out. Caution! Lamp may still be hot! Be sure
lamp has cooled before touching.
b. Inspect socket for any damage.
c. Clean inside of xture and Cap with a clean dry cloth.
d. Push new lamp straight in, being careful to align pins. Note:
Replacement lamp must not exceed ratings on Label.
For LED Module:
a. Loosen and remove the LED Module Screws using a 1/16” hex tool.
b. Pull LED straight out. Do not twist or the pins will break off in the
socket. Caution! LED may still be hot! Be sure LED has cooled
before touching.
c. Clean the grease off of the Heatsink top surface using a rag dipped
in alcohol.
d. Inspect the socket for any damage.
e. Apply a thin layer of thermal grease (not supplied) to the surface of
the Heatsink that will contact the bottom of the LED Module.
f. Align the pins on the LED Module with the socket and push straight
in. Do not twist or push in at an angle or the pins may be damaged.
g. Install and tighten the LED Module Screws. Caution! Over
tightening of screws could crack the LED Module case.
7. Re-install Socket Mount Assembly in to Faceplate Assembly.
8. Tighten Faceplate Set Screw with the 3/32” hex tool so that is just bottoms
out.
Mount Base
Body Mount Screws (4X)
Stake (optional)
2 7/8"
1 1/2"
Ø7/16"
Bolt Hole
Surface Mount Base
Hole Pattern
Body
Cover (optional)
Cover Set Screws (3X)
Faceplate Assembly
Label
MR16 Halogen Lamp
Accessory Clip
Accessories Socket Mount Assembly
Faceplate Screws (2X)
LED Version
LED Module
LED Module Screws
Socket
Heat Sink &
Socket Mount

- Page 2 -
Installation Instructions
©2005-2016 Vision3 Lighting™ P.O. Box 607, Fowler, CA 93625 [phone] [phone] fax www.vision3lighting.com
revision 5/12/16
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
(Failure to follow the warnings and instructions on this sheet could result in re, injury, failure of product, and/or voiding of warranty.)
MR16 Bollard Path Light MODEL PA7
12-24 Volt AC/DC, 10 Watt, LED
12 Volt, 50 Watt Max., MR16 Halogen
9. Insert the Faceplate Assembly in to the Body. Note: Make sure the wiring
is not kinked or pinched in any way.
10. Use the Faceplate Screws (2X) to attach the Faceplate Assembly to the
Body. Notes: Skip the next steps if your xture does not have a cover
option:
11. Slide the Cover over the Faceplate as far as it will go, and properly orient.
Note: Eyelid should not be pointed up as it will ll with water and debris.
12. Gently tighten each Cover Set Screw against Faceplate.
LED Switching (on certain models):
1. Remove the Faceplate Assembly to gain access to the LED Module as
explained in Lamp Maintenance steps 1 thru 5 above.
2. Inspect for damage. Replace any
damaged parts, if necessary.
3. Clean inside of xture with a clean,
damp cotton cloth.
4. Find LED High/Low Switch on side
of LED Module.
5. Using a pin, small nail, etc, ip the
switch in the desired direction. See
the LED Module Switch sketch for
which direction corresponds to which setting.
6. Re-assemble as explained in Lamp Maintenance steps 7 thru 12 above.
Accessory Maintenance:
1. Remove the Faceplate Assembly to gain access to the accessories, as
explained in Lamp Maintenance steps 1 thru 5 above.
2. Remove Accessory Clip from Cap.
3. Carefully remove Accessories from Cap, if any.
4. Inspect Cap, Accessories, and Clip for damage. Replace if necessary.
5. Clean Cap and Accessories with a clean, damp cotton cloth.
6. Carefully install new Accessories into Cap (Cap may hold up to 2
Accessories).
7. Compress Clip and push into Cap until it holds Accessories tightly in
Cap.
8. Re-assemble as explained in Lamp Maintenance steps 7 thru 12 above.
LED Module Switch
LowHigh
LED Module
LED High/Low Switch
PA7 Heatsink