visplay Invisible 3 User manual

play it smart
Invisible 3
Assembly and operating instructions
USA & CANADA

2
General Instructions
1/2019 (US)
Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning, installation
and/or use of our products must be carefully read
and observe these instructions of use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports with
anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding 200 mm/
7.874" must be subjected to abrasive cleaning using
detergents specifically developed for this purpose. The
cleaning agents developed for abrasive cleaning contain
very finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.
Copyright
This manual is protected by copyright. Its use is
permissible as part of the use of the product. Any use
other than this is not permitted without written consent of
the manufacturer.
Our General Terms and Conditions apply for all orders.
www.visplay.com | [e-mail]
Dimensions are generally shown in millimeters and
inches.

3
Invisible3
ø 3.6
0.142”
20
0.787”
5
0.197”
20
0.787”
40
1.575”
50
1.969”
27
1.063”
(13)
(0.512”)
(17.75)
(0.699”)
(19.25)
(0.758”)
1.9
0.075”
4.2
0.165” 4.2
0.165”
1.5
0.059”
6.1
0.240”
100 ±0.5
3.937”±0.020
3100 / lto (min. 250–max. 3100)
122.047” / lto (min. 10”–max. 122”)
100 ±0.5
3.937”±0.020
3
+0.1
– 0.05
3”
+0.004”
– 0.002”
0
-0.5
0
-0.020”
0
-0.5
0
-0.020”
(3.1)
(0.122“)
(8)
(0.315“)
2 x 3.1 /2 x 0.122“
Length of groove = length of profile +
Length of profile
+0.4
–0.1
+0.5
0 +0.020“
0
2 x 7.25 /2 x 0.285“
Length of groove = length of profile +
Rear
+0.5
0 +0.020“
0
+0.016“
–0.004“
0
- 0,2
0
- 0.008“
R 3.1
0.122“
+0.2
0
+0.008“
0
R 7.4
0.291“
+0.2
0
+0.008“
0
14.8
0.583“
+0.3
0
+0.012“
0
6.3
0.248“
+0.2
0
+0.008“
0
40
1.575”
(12.3)
(0.484”)
(18.9)
(0.74 4”)
16
0.630”
3.7
0.146”
(A – 6)
(A – 0.236“)
(A)
1/2019 (US)
Examples of fixation
Assembly dimensions / Layout - Invisible profile for  mm wooden panel
Reinforcement Reinforcement Reinforcement
Substructure
Layout
Panels and sub-structures must be
toughened against bowing. Wooden
ledges or angle sections are suitable for
this purpose.
glued and screwed

4
Invisible3
4.7
0.185“
(12.3)
(0.484“)
16
0.630“
4.2
0.165“
+0.2 0
+0.008“ 0
3.7
0.146“
0
-0.2
0
-0.008“
+0.0.016“
–0.004“
+0.4
-0.1
2.7
0.106“
+0.2 0
+0.008“ 0
1.5
0.059“
+0.2
0
+0.008“
0
3.7
0.146“
0
-0.2
0
-0.008“
16
0.630“+0.0.016“
–0.004“
+0.4
-0.1
ABC
25
0.984”
ø 4.5
0.177”
150
5.906”
18
0.709”
33.3
1.311”
22
0.866”
40.5
1.594”
48
1.890”
6.5
0.256”
33.3
1.311”
29.7
1.169”
100
3,937”
117.5
4.626”
3100 / lto (min. 250–max. 3100)
122.047” / lto (min. 10”–max. 122”)
0
-0.5
0
-0.020”
3100 / lto (min. 250–max. 3100)
122.047” / lto (min. 10”–max. 122”)
0
-0.5
0
-0.020”
34
1.339”
33.3
1.311”
33.3
1.311”
33.3
1.311”
29.5
1.161”
231.5
9.114”
66.7
2.626”
24.4
0.961”
100
3,937”
1/2019 (US)
Assembly instructions
The following steps must be carried out when assembling the Invisible  profile for  mm/" wooden panel:
 Screw first profile to the lowest panel from the rear using  x mm/" x " wood screws - see »A« for edge contour.
 Screw pre-mounted panel to substructure from the front. The indicated bore holes must be countersunk in the profile. The profile is screwed to the
substructure using countersunk screws - see »B«.
 All further profiles are to be pre-assembled according to steps  and  fitted to the lower profile and screwed together. See »C« for bottom panel
groove.
Assembled directly onto the wall Assembled onto
substructure
e.g. Fixation profile
Invisible3 profiles are available in two dierent versions:
• Single sided (18mm/0.709") assembled on wooden panels
• Double sided (34mm/1.339") assembled between profile frames (min. 35 mm/1.378")
Assembly dimensions / Layout - Invisible profile single sided and double sided
Invisible3 profile double-sided
Invisible3 profile single sided

5
Invisible3
22
0.866”
122
4.803”
150
5.906"
150
5.906"
Recommendation:
bar to support
bottom profile edge
19
0.748"
(16)
(0.630")
13.5
0.531"
B
Recommendation:
fit screw at least every
300 mm/11.811"
A
ACountersunk screw M5 x 30 mm/1.181"
BPan-head screw 4 x 5 mm/0.157"x 0.197"
Recommendation:
use all fixation points, i.e. fit
screw every 150 mm/5.906"
33.3
1.311”
22.4
0.882”
66.7
2.626”
66.7
2.626”
1/2019 (US)
Assembly instructions Invisible3 profile panels one-sided
The following steps must be carried out when
assembling a one-sided profile:
1. Fasten the lowest profile to the wooden pa-
nel (min. 16 mm/0.630") from the front using
a 4 x 15 mm/0.591" screw and from the rear
using a M5x20mm/0.787" screw.
2. Insert a profile into the top of the bottom pro-
file - making sure that the profile is correctly
locked into place - and fasten to the wooden
panel with 4x15mm/0.591" screw.
3. Insert Invisible 3 end profile - making sure
that the profile is securely locked in place.
4. Attach frame to support panel.
Frame
Assembly instructions Invisible3 profile panels double-sided
The following steps must be carried out when
assembling a two-sided profile:
1. Connect double-sided Invisible3 profile
panels to one another - making sure that
each profile is securely locked in place.
2. Fit the end profile at the top - making sure
that it is securely locked in place.
3. Popular frame solutions (e.g. wood) are to
be screwed to the Invisible3 profiles with M5
screws from the side.

6
Invisible3
1250
49.213"
1240
48.819"
1250
49.213"
900
35.433"
350
13.780"
350
13.780"
350
13.780"
350
13.780"
350
13.780"
450
17.717
"
1540
60.630"
555
21.850"
2500
98.425"
60
2.362" 640
25.197"
640
25.197"
655
25.787"
50
1.969“
8
0.315“
3.5
0.138“
1x45°
0.5
0.020“
0.5
0.020“
15.3
0.602“
2.2
0.087“
6.6
0.260“
1.7
0.067“
11
0.433“
6.1
0.240“
1/2019 (US)
Weight loads
Invisible3 panel (one-sided)
Panel with aluminium frame, to be attached with fixing set
(fixing sets per panel are required).
Max. load
Profile per  mm/" lbs
Profile panels one-sided per  mm/"split over all grooves  lbs
Profile panels double-sided per  mm/"split over all grooves  lbs
Front arms Ømm/5⁄16" lbs
Side hanging frame Ø 15 x 400 mm/5⁄8" x "  l b s
Hooks Ømm/1⁄4" lbs
Hooks Ømm/⁄" lbs
Looped hooks Ømm/⁄" lbs
Glasses holder  lbs
Clamp bracket for glass shelf per bracket  lbs
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please observe that max. weight loads decreases as the merchandise support increases in length.
Please observe that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports produce an uneven overall appearance of the goods display.
The max. weight loads of Invisible3 depends on the nature of the wall, on the number of fixation points as well as on the fixation material
used. All fixation points are to be used with a maximum weight load.
Please also observe the weight loads indicated in our sales documentation.
Instructions of use
The Invisible accessories/shelves are
inserted in to the holders or profile at a slight
angle until the limit stop is reached.
Then lower the accessory/shelf.
Check that the accessory is correctly clicked
into the profile.
Assembly dimensions - Invisible profile double sided for gondolas
Also glue with PUR rigid foam

Visplay Companies
Oces & Showrooms
Visplay Exclusive Dealers / Sales Agents /
Authorized Distributors
Australia
Distributed by MADE Retail Systems
Authorized Distributor
2 Stephenson Street
Cremorne Vic 3121
Melbourne
Australia
T [phone]
[e-mail]
Brazil
Distributed by Instant Shop
Authorized Distributor
Av. Nove de Julho, 5017 # 51
Cj. 51 - 5° Andar
São Paulo, SP - CEP 01407-200
Brazil
T [phone]
[e-mail]
China
Distributed by Okamura Shanghai
Authorized Distributor
15Fax: B block, FutureLand building
No.5 Lane 388, Zhongjiang Road
Putuo District
Shanghai 200062
China
T [phone]
[e-mail]
Greece
Distributed by KYVERNITIS I. SA
Exclusive Dealer
125, G. Papandreou & Adrianiou str.
144 51 Metamorfosi Athens
Greek
T [phone]
[e-mail]
India
Distributed by
Matrix Visual Innovations Pvt. Ltd.
Authorized Distributor
45/1, 2nd Floor, Corner Market,
Malviya Nagar
New Delhi 110017
India
T [phone]
[e-mail]
Italy
Distributed by Zeppelin s.r.l.
Exclusive Dealer
Via Matteucci, 2
61032 Fano PU
Italy
T [phone]
[e-mail]
Japan
Distributed by
Okamura Corporation
Exclusive Dealer
Higashi Ote Bldg.,
1F1-1-7, Uchikanda, Chiyoda-ku
Tokyo 101-0047
Japan
T [phone]
[email protected]
Panama
Distributed by Vidisplay S. A.
Authorized Distributor
Calle Ramon Jurado,
Paitilla Mall, Local 17 Piso 1
Punta Paitilla
Panama
Ciudad de Panamá
T [phone]
[e-mail]
Poland, Czech Republic & Baltics
Distributed by
Meškank Interior Brands
Sales Agent
T [phone]
[e-mail]
Russia
Distributed by ULTIMATHULE
Exclusive Dealer
Business quartel „ARMA“
Nizhniy Susalniy per., 5 bld.18
105065 Moscow
Russia
T [phone]
[email protected]
Saudi Arabia
Distributed by Saudi TKT
Authorized Distributor
P.O. Box 10700
Jeddah 21443
Saudi Arabia
T [phone]
[e-mail]
Turkey
Distributed by
Dekotek Mimarlık Ltd. Sti
Exclusive Dealer
Sair Nigar Sokak 80/8 Osmanbey
34363 Istanbul
Turkey
T [phone]
[e-mail]
For other countries:
Visplay GmbH
Charles-Eames-Str. 2
79576 Weil am Rhein
T [phone]
[e-mail]
Austria
Visplay Austria
Schottenring 12
1010 Wien
Austria
T [phone]
[e-mail]
Belgium
Visplay Belgium
Woluwelaan 137
1831 Diegem
Belgium
T [phone]
[e-mail]
France
Visplay France
So Square Opéra
5, Rue Boudreau
75009 Paris
France
T [phone]
[e-mail]
Germany
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Germany Showroom
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Netherlands
Visplay Netherlands
De Oude Molen 2
1184 VW Ouderkerk aan de Amstel
Netherlands
T [phone]
[e-mail]
Spain/Portugal /Latin America
Visplay Spain
Calle Padilla, 21
28006 Madrid
Spain
T [phone]
[e-mail]
United Arab Emirates
Visplay GmbH (Dubai BR)
Sheikh Zayed Road
P.O. B ox : 21 3 0 3 5
Sheikha Sana Mana
Al Maktoum Building
Oce - M 10
Dubai
T [phone]
[e-mail]
United Kingdom
Visplay United Kingdom
30 Clerkenwell Road
London EC1M 5PG
United Kingdom
T [phone]
[e-mail]
USA
Visplay Inc.
7528 Walker Way
Allentown, PA 18106
USA
T [phone]
[e-mail]