visplay Xero 4 User manual

play it smart
Xero 4
Assembly and operating instructions
USA & CANADA

2
General Instructions
1/2019 (US)
Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning, installation
and/or use of our products must be carefully read
and observe these instructions of use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports with
anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding 200 mm/
7.874" must be subjected to abrasive cleaning using
detergents specifically developed for this purpose. The
cleaning agents developed for abrasive cleaning contain
very finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.
Copyright
This manual is protected by copyright. Its use is
permissible as part of the use of the product. Any use
other than this is not permitted without written consent of
the manufacturer.
Our General Terms and Conditions apply for all orders.
www.visplay.com | [e-mail]
Dimensions are generally shown in millimeters and
inches.

3
Xero4
Xero 4 Xero 4 T
15
0.591"
17
0.669"
16
0.630"
64.5
2.539"
42.5
1.673"
26.5
1.043"
54.5
2.146"
+ 0.3 0
+ 0.012" 0
15
0.591"
17
0.669"
35
1.378"
11.8
0.465"
26
1.024"
16
0.630"
R 6
0.236"
6
0.236"
22
0.866"
25
0.984"
± 0.1
± 0.004"
25
0.984"
± 0.1
± 0.004"
± 0.1
± 0.004"
+ 0.3 0
+ 0.012" 0
22
0.866"
25
0.984"
± 0.1
± 0.004"
25
0.984"
± 0.1
± 0.004"
R 6
0.236"
6
0.236"
12 + 0,5
0
0.472"+ 0.020"
0
12+ 0,5
0
0.472"+ 0.020"
0
4.4+ 0.1
0
0.173"+ 0.004"
0
4.4+ 0.1
0
0.173"+ 0.004"
0
Example: rect
angular tube
50 x 40/1.969" x 1.575"
16
0.630"
Assembly axis = fixing axis: 617.5/1242.5 / 24.311"/48.917"
Assembly axis –40/–1.575"
1/2019 (US)
Xero Aluminium extrusions can be hung on various bases on the wall and in mid-floor.
All ranges of accessories in chrome and silk can be used.
Powder-coated accessories can not be used.
Assembly dimensions / Layout
Assembly dimensions
Please observe the indications concerning weight loads and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.

4
Xero4
A 617.5
24.311"
A 617.5
24.311"
A 617.5
24.311"
A 1242.5
48.917"
1 2 3
3x
929-226.21
170
6.693“
16
0.630“
glued and screwed
A 609.6 mm/24" Accessories Xero 4 (ø 25/0.984") A 406.4 mm/16" + Accessories Xero 4 (ø 15/0.591")
150
5.906"
2138.4
84.189"
2438.4
96"
150
5.906"
406.4
16"
203.2
8"
304.8
12"
406.4
16"
406.4
16"
406.4
16"
1219.2
48"
1219.2
48"
609.6
24"
609.6
24"
609.6
24"
1/2019 (US)
Please note the dierent
assembly axes. With Xero
profiles, accessories cannot be
used over two axes.
Recommendation for grid arrangement
Inserting the panels into Xero  profile
Layout
Panels and sub-structures must be
toughened against bowing.
Wooden ledges or angle sections are
suitable for this purpose.

5
Xero4
342-830.31
362-079.31
Xero 4 T
Xe
ro 4 981-479.05/.06 981-479.05/.06
930-087.08
930-088.08
929-225.65
930-087.08
930-088.08
929-225.65
1
1 2
2
929-225.65
929-225.65
333-868.05/.06
333-381.05/.06
333-869.05/.06
16
0.63
0"
16
0.630"
333-382.05/.06
337-021.05/.06
12 + 0.5
- 0
0.472"+ 0.020"
- 0 R 6
0.236"
12 + 0.5
- 0
0.472"+ 0.020"
- 0 R 6
0.236"
1/2019 (US)
The aluminium profile must be fixed to the panel.
Assembly instructions
Shelf dimension for bracket 342-830.31
Shelf dimension for single bracket 362-079.31
Production drawings of glass
wooden are available for downloading
on www.visplay.com or can be received
on request.
Drawing no. 247-734
Production drawings of glass
wooden are available for downloading
on www.visplay.com or can be received
on request.
Drawing no. 247-138
Assembly on wooden panels
Please note that the fixing set 929-225.65 cannot be attached to Xero4T profiles. Panels with these profiles are to be attached to the wall
e.g. with wedge gibs.
Please observe the indications concerning weight loading and ensure that the substructure of the wall units and their fixtures can support
the expected loads.
Screw tho profile Xero  or Xero T on to the panel from the rear. Fit fixing sets to the Xero profile () or wooden ledges (). The wooden ledge ()
must be fixed to the panel (glued and screwed) near the Xero  T profile. Fix the profile end caps above and down to the profile, before the profile is
installed to the panel.

6
Xero4
1.2
1.3 1.5
1.9
1.9
1.1
1.2
1.1
1.3
Separating tape
1/2019 (US)
Layout information can be found on the drawing 320-143.
1.1 Insert profile end caps 981-479.05 on top and on bottom
1.2 The cross-connections are fixed to the side of the sytem uprights using two M6 x 12/0.472" thread grooving screws —> do not overtighten
screws!
1.3 The bracket of the wall attachment kit is attached to the side of the system uprights using two M6 x 12/0.472" thread grooving screws —> do not
overtighten screws! At least 2 brackets are required per upright - the number depends on the condition of the wall.
1.4 Assemble the uprights into single unit.
1.5 Set up unit, and ensure that it is perfectly aligned in height and that it is perpendicular.
1.6 Mark mounting points.
1.7 Drill holes in wall and insert dowels.
1.8 Reposition wall unit and screw into place. Proceed as described in point 1.5.
1.9 Important: Wind separating tape smoothly around the profile (we recommend: Knauf Trenn-fix 65)
The wall uprights must be screwed to the wall with at least 2 Ø 6mm/0.236“ screws. The wall and its fixtures must be capable of taking a
min. fraction weight of 1.6 kN. Please observe the instructions supplied by the dowel manufacturer.
Assembly in plasterboard
1. Assembling wall upright
Please observe the indications concerning weight loads and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.

7
Xero4
2.1
CW
CW
UW
UW
2.1
CWCW
UW
UW
25
0.984"
A 609.6 / 406.4
A 24" / 16"
105
4.134"
75
2.953"
12.5
0.492"
(142–151)
(5.591"–5.945")
1/2019 (US)
• Upright axis: 609.6 mm/24" and 406.4 mm/16"
• Depth of panel structure: 142–151 mm/5.591"–5.945"
• Layout information can be found on the drawing 320-143
Please observe the indications concerning weight loads and ensure that the substructure of the wall units and their fixtures can support the expected
loads
2.1 Set-up metal frame (UW- and CW-profiles): check that profiles are aligned with UW profile.
The structure of the wall unit is designed for metal frames with a profile width of 75mm/2.953"
2. Assembling metal frame
Dimensions: plasterboard
alignment
UW: UWprofile UW 75 x 40 mm
2.953" x 1.575"
CW: CWprofile CW 75 x 50 mm
2.953" x 1.969"
Single gypsum panels Double gypsum panels

8
Xero4
3.2
3.3
3.1
12.5
0.492“
ACB
D
E
F
1/2019 (US)
3.1 Screw the gypsum panels to the metal frame profile using dry wall screws A(e.g.
Ø3.9x19 mm/0.154"x 0.748").
Also screw the gypsum panels to the slotted rails - dry wall screws with drill bits B
are necessary (e.g. Ø3.5x19 mm/0.138"x 0.748")
Recommendations:
- cover joints Cwith reinforcing tape D.
- add edge safety profiles if necessary.
Final paintwork (finishing)
3.2 Cut-o protuding strips of separating tape E.
3.3 Recommandation:
Apply a finely-structured glass fibre yarn mat to avoid visible cracks.
Cover visible surface of the profile Fwith easily removable masking tape (no residue) before beginning paintwork.
3.4 Final paintwork or other finishes.
3. Covering and smoothing

9
Xero4
1/2019 (US)
Weight loads
Please observe the permissible weight loads of the accessories used.
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please observe that max. weight loads decreases as the merchandise support increases in length.
Please observe that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports produce an uneven overall appearance of the goods display.
The max. weight loads of Xero 4 depends on the nature of the wall, on the number of fixation points as well as on the fixation material used.
All fixation points are to be used with a maximum weight load.
Please also observe the weight loads indicated in our sales documentation.
Max. load
Profile per 1000 mm per 40"  lbs
Front arms Ø 25 mm/1" 55 lbs
Front arms 30 x 15 mm/13⁄16" x 5⁄8" 44 lbs
Front arms Ø 12 mm/½" 22 lbs
Front arms mm/⁄" 22 lbs
Hook Ø 6 mm/1⁄4" 4.4 lbs
Hook Ø 7. 5 m m /9⁄32" 4.4 lbs
Side hanging rail T arm Ø 25, 600 mm/1", 24" 44 lbs
T-bracket Ø 25 mm/1" for wooden or glass shelf per bracket 44 lbs
T-bracket 25 x 4 mm/1" x 5⁄32" for wooden or glass shelf per bracket 44 lbs
Bracket for side hanging rail Ø 25 mm/1" per bracket 44 lbs
Bracket for side hanging rail Ø 25 mm/1" and wooden or glass shelf per bracket 44 lbs
Bracket for side hanging rail Ø 15 mm/5⁄8"per bracket 22 lbs
Bracket  x  mm/⁄" x ⁄" for glass shelf per bracket 44 lbs
Bracket  x  mm/⁄" x ⁄" for wooden shelf per bracket 44 lbs
Bracket Ø 15 mm/5⁄8" for wooden shelf, concealed per bracket 33 lbs
Single bracket Ø 15 mm/5⁄8" for wooden shelf, concealed 33 lbs
Bracket for back bar  x  mm/⁄" x ⁄"per bracket 44 lbs
Clamping bracket for glass shelf 33 lbs
Hook rail for ties, belts etc. 22 lbs

Visplay Companies
Oces & Showrooms
Visplay Exclusive Dealers / Sales Agents /
Authorized Distributors
Australia
Distributed by MADE Retail Systems
Authorized Distributor
2 Stephenson Street
Cremorne Vic 3121
Melbourne
Australia
T [phone]
[e-mail]
Brazil
Distributed by Instant Shop
Authorized Distributor
Av. Nove de Julho, 5017 # 51
Cj. 51 - 5° Andar
São Paulo, SP - CEP 01407-200
Brazil
T [phone]
[e-mail]
China
Distributed by Okamura Shanghai
Authorized Distributor
15Fax: B block, FutureLand building
No.5 Lane 388, Zhongjiang Road
Putuo District
Shanghai 200062
China
T [phone]
[e-mail]
Greece
Distributed by KYVERNITIS I. SA
Exclusive Dealer
125, G. Papandreou & Adrianiou str.
144 51 Metamorfosi Athens
Greek
T [phone]
[e-mail]
India
Distributed by
Matrix Visual Innovations Pvt. Ltd.
Authorized Distributor
45/1, 2nd Floor, Corner Market,
Malviya Nagar
New Delhi 110017
India
T [phone]
[e-mail]
Italy
Distributed by Zeppelin s.r.l.
Exclusive Dealer
Via Matteucci, 2
61032 Fano PU
Italy
T [phone]
[e-mail]
Japan
Distributed by
Okamura Corporation
Exclusive Dealer
Higashi Ote Bldg.,
1F1-1-7, Uchikanda, Chiyoda-ku
Tokyo 101-0047
Japan
T [phone]
[email protected]
Panama
Distributed by Vidisplay S.A.
Authorized Distributor
Calle Ramon Jurado,
Paitilla Mall, Local 17 Piso 1
Punta Paitilla
Panama
Ciudad de Panamá
T [phone]
[e-mail]
Poland, Czech Republic & Baltics
Distributed by
Meškank Interior Brands
Sales Agent
T [phone]
[e-mail]
Russia
Distributed by ULTIMATHULE
Exclusive Dealer
Business quartel „ARMA“
Nizhniy Susalniy per., 5 bld.18
105065 Moscow
Russia
T [phone]
[email protected]
Saudi Arabia
Distributed by Saudi TKT
Authorized Distributor
P.O. Box 10700
Jeddah 21443
Saudi Arabia
T [phone]
[e-mail]
Turkey
Distributed by
Dekotek Mimarlık Ltd. Sti
Exclusive Dealer
Sair Nigar Sokak 80/8 Osmanbey
34363 Istanbul
Turkey
T [phone]
[e-mail]
For other countries:
Visplay GmbH
Charles-Eames-Str. 2
79576 Weil am Rhein
T [phone]
[e-mail]
Austria
Visplay Austria
Schottenring 12
1010 Wien
Austria
T [phone]
[e-mail]
Belgium
Visplay Belgium
Woluwelaan 137
1831 Diegem
Belgium
T [phone]
[e-mail]
France
Visplay France
So Square Opéra
5, Rue Boudreau
75009 Paris
France
T [phone]
[e-mail]
Germany
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Germany Showroom
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Netherlands
Visplay Netherlands
De Oude Molen 2
1184 VW Ouderkerk aan de Amstel
Netherlands
T [phone]
[e-mail]
Spain/Portugal/ Latin America
Visplay Spain
Calle Padilla, 21
28006 Madrid
Spain
T [phone]
[e-mail]
United Arab Emirates
Visplay GmbH (Dubai BR)
Sheikh Zayed Road
P.O. B o x: 2 1 3 0 3 5
Sheikha Sana Mana
Al Maktoum Building
Oce - M 10
Dubai
T [phone]
[e-mail]
United Kingdom
Visplay United Kingdom
30 Clerkenwell Road
London EC1M 5PG
United Kingdom
T [phone]
[e-mail]
USA
Visplay Inc.
7528 Walker Way
Allentown, PA 18106
USA
T [phone]
[e-mail]