Vivo STAND-TV86B User manual

Black Steel Easel Studio TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv86b
SKU: STAND-TV86B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
B(x4)
Leg
C(x2)
Pole
D (x1)
Upper VESA Bracket
E (x1)
Lower VESA Bracket
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualied technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specied in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
F (x1)
Security Cable
G (x2)
Security Clip
H(x2)
Security Cable Clamp
T-A (x1)
4mm Allen Wrench
W-A (x4)
ST4.8x38 Screw
W-B (x4)
Concrete Anchor
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting hardware for brick and concrete walls. If unsure, please contact us at
vivo-us.com, email at [email protected]om, or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M5x14mm Screw
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm SCrew
M-E (x4)
M8x50mm Screw
M-F (x4)
Square Washer
M-G (x8)
5mm Spacer
M-H (x8)
15mm Spacer
A(x1)
Base
T-B (x1)
5mm Allen Wrench
TOOLS NEEDED
Phillips Drill Tape Measure Level Pencil
S-A (x4)
M6x30mm Screw
M-I (x2)
M5 Washer
T-C (x1)
2mm Allen Wrench

3
ASSEMBLY STEPS
STEP 1
Remove the cable management covers from Legs (B).
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
132lbs
(60kg)
STEP 2
Assemble Legs (B) to Base (A) using M6x30mm Screws (S-A) and M5mm Allen Wrench (T-B).
STEP 3
B
B
A
S-A
T-B
Thread Poles (C) onto Base (A).
C
A

4
STEP 4
STEP 5
Loosen the collars on Poles (C) using 4mm Allen Wrench (T-A). Adjust collars to hold TV at desired
height, using a tape measure to ensure the rings are adjusted evenly, and tighten with 4mm Allen
Wrench (T-A).
NOTE: Rings should be 2”-6” below the tops of the poles.
C
Remove the screws from Lower VESA Bracket (E) and open the clamps.
T-A
Secure Upper VESA Bracket (D) and Lower VESA Bracket (E) to the
back of the TV using Screws (M-A or M-B) with Square Washers
(M-F) and M5 Washers (M-I), with Security Clips (G) installed in the
top holes.
OPTION A: Flat Back Monitor
OPTION B: Curved Back Monitor Secure Upper VESA Bracket (D) and Lower VESA Bracket (E) to the
back of the TV using Screws (M-C, M-D or M-E) with Square Washers
(M-F) and Spacers (M-G, M-H) with Security Clips (G) installed to
top holes.
D
E
GG
GG
D
E
2”-6”
E
M-I

5
STEP 6
Slide the TV with Upper VESA Brackets (D) and Lower VESA Bracket (E) onto Poles (C). Close the clamps
on Lower VESA Bracket (E) around Poles (C) and secure with previously removed screws.
NOTE: Make sure the TV does not touch Base (A).
STEP 7
Route cables through Legs (B) and secure using the previously removed cable management covers.
B
D
E
C
A

6
STEP 8 (Option A)
Wood Stud Wall:
Using Security Cable Clamps (H) as guides, mark drilling locations on wall at the same height as Upper
VESA Bracket (D). Use of a stud nder is recommended. Drill holes at least 1.6” (40mm) deep using a 1/8”
(3.5mm) drill bit. Mount clamps to wall using ST4.8x38 Screws (W-A). Thread Security Cable (F) through
Security Clips (G) on TV and center holes in Security Cable Clamps (H) as shown, then tighten clamps
using the 2mm Allen wrench (T-C).
H
D
W-A
F
T-C
H
G
H

7
STEP 8 (Option B)
Concrete/Brick Wall:
Using Security Cable Clamps (H) as guides, mark drilling locations on wall at the same height as Upper
VESA Bracket (D), spaced 16” - 26” (400mm - 650mm) apart. Drill holes at least 1.6” (40mm) deep using a
9/32” (7mm) drill bit. Insert Concrete Anchors (W-B) into holes and mount Security Cable Clamps (H) to
wall using ST4.8x38 Screws (W-A). Thread Security Cable (F) through Security Clips (G) on TV and center
holes in Security Cable Clamps (H) as shown, then tighten clamps using the 2mm Allen Wrench (T-C).
H
D
W-B
W-A
H
G
F
T-C
H

LAST UPDATED: 08/29/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303