Vivo STAND-RACE1A User manual

Racing Steering Wheel Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-race1a
SKU: STAND-RACE1A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
Peel the backing o of So Pads (D) and apply to the bottom of Feet (C). Screw Feet (C) into bottom
of Stand (A).
PACKAGE CONTENTS
44lbs
(20kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x1)
Stand
B(x1)
Upright Support
Plate
C(x4)
Foot
J (x1)
Shier Plate
K (x4)
M6x12 Screw
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D(x4)
So Pad
E(x2)
Cable Clip
F (x4)
M8x16 Screw
G(x6)
Ziptie
H (x1)
5mm Allen
Wrench
I (x1)
Shier Support
Bracket
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
STEP 2
Loosen the knobs on the middle of the post on Stand (A), then extend the post.
Remove the two knobs locking the post in the folded position. Raise the post, then
install the Upright Support Plate (B) to the base and post using M8x16 Screws (F)
and the previously removed knobs. Tighten screws with 5mm Allen wrench (H).
STEP 3
Tilt the wheel plate on Stand (A) up to the desired angle, then insert M8x16 Screws (F) to secure the
tilt angle. Tighten with 5mm Allen Wrench (H).
A
H
11
2
BFH

4
STEP 4
STEP 5
Adjust the foot plate on Stand (A) to the desired angle and reinsert the previously removed knobs.
Remove the knobs from the foot plate in Stand (A). Remove the screws using 5mm Allen wrench (H),
move the foot plate to the desired position (1-5), then reinstall the screws.
A
H
A
1 2 3 4 5

5
STEP 6
Adjust the post on Stand (A) to the desired height, then tighten the knobs to secure the height.
Install Shier Support Bracket (I) to the le or right side of the wheel support plate on Stand (A) using
M6x12 Screws (K). Tighten with 5mm Allen Wrench (H).
STEP 7
A
A

6
STEP 8
STEP 9
Attach Cable Clips (E) to the post on Stand (A) for cable management.
Mount Shier Plate (J) to Shier Support Bracket (I) using M6x12 Screws (K) and tighten with 5mm
Allen wrench (H). Shier Plate (J) may be installed to the close or far position depending on user
preference.
I
H
A

7
STEP 10
FOLDING INSTRUCTIONS
Remove the lower two knobs (A1) from the UprightSupport Plate (B) and gently fold the post down.
Loosen the knobs on the middle of the post to extend for clearance if needed. Reinsert the previously
removed knobs into the sides to lock the post in the folded position.
A1
B

LAST UPDATED: 08/05/2021
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303