Vivo STAND-V002FGL User manual

Monitor and Laptop Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002fgl
SKU: STAND-V002FGL
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
15.4lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Pole
B(x1)
Base
C(x1)
Laptop Arm
I(x1)
Grommet Plate
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualied technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specied in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Monitor Arm
E(x2)
VESA Plate
F (x1)
Laptop Tray
G(x1)
So Pad
H (x1)
Base Plate
K (x1)
Pole Cover
J(x1)
Pole Base
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x4)
M4x8mm
Screw
S-B (x4)
M4 Nut
S-C (x2)
M6 Nut
S-D (x3)
M6x16mm
Screw
T-A (x1)
4mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench
T-D (x1)
Wrench
M-A (x8)
M4x12mm
Thumbscrew
M-B (x8)
M4x30mm
Screw
M-C (x8)
M4 Spacer
L (x1)
Pole Cap
M (x4)
Foot Pad
N (x3)
Arm Cable Clip
O (x1)
Pole Cable Clip
T-B (x1)
5mm Allen
Wrench
S-E (x4)
M6x20mm
Screw
9.9lbs
(4.5kg)
MONITOR ARM LAPTOP
P (x4)
Pad

3
ASSEMBLY STEPS
STEP 1
Assemble Pole Base (J) to Pole (A) using M6x16mm Screws (S-D) and 4mm Allen Wrench (T-A). Insert
Grommet Plate (I) into Pole Base (J).
STEP 2
Remove adhesive backing from So Pad (G) and stick it to the top of Base Plate (H) making sure the
holes in both line up. Assemble Base Plate (H) with Base (B) to the pole assembly using M6x20mm
Screws (S-E) and 4mm Allen Wrench (T-A).
T-A S-D
J
A
I
G
A
B
H
S-E
T-A
H
STEP 3
Remove adhesive backing from Foot Pad (M) and stick
it to the bottom of Base (B). Slide Pole Cover (K) over
Pole (A).
M
B
K
A

4
STEP 4
Remove adhesive backing from Pads (P) and stick them to Foot Pads (M).
STEP 5
Slide Monitor Arm (D) over Pole (A). Secure Monitor Arm (D) at the desired height using 6mm Allen
Wrench (T-C).
D
T-C
A
P
M

5
STEP 6
Slide Laptop Arm (C) over Pole (A). Secure Laptop Arm (C) at the desired height using 6mm Allen
Wrench (T-C). Insert Pole Cap (L) into the top of Pole (A).
STEP 7
Attach Arm Cable Clips (N) to Laptop Arm (C) and Monitor Arm (D), and Pole Cable Clip (O) to Pole
(A).
T-C
L
C
N
O
A
C
D
A

6
STEP 8
Secure VESA Plate (E) to the back of the monitor using M4x12mm Thumbscrews (M-A), or M4x30mm
Screws (M-B) and M4 Spacers (M-C).
STEP 9
Assemble VESA Plate (E) to Laptop Tray (F) using M4x8mm Screws (S-A) and M4 Nuts (S-B).
Tighten using Wrench (T-D) and a Phillips screwdriver.
S-B
T-D
S-A
F
E

7
STEP 11
Place your laptop on Laptop Tray (F). Adjust tilt using 5mm Allen Wrench (T-B).
Slide the monitor with VESA Plate (E) onto Monitor Arm
(D), and VESA Plate (E) with Laptop Tray (F) onto Laptop
Arm (C). Secure VESA Plates (E) with M6 Nuts (S-C).
STEP 10
S-C
T-B
E
E
D
F
C
F
STEP 12
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.

LAST UPDATED: 05/31/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303