Vivo STAND-V103C User manual

Flush to Wall Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v103c
SKU: STAND-V103C
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Clamp
C(x3)
VESA Plate
J (x1)
So Pad
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x2)
Arm
E(x2)
Arm Extension
F (x2)
Side VESA
Bracket
G(x1)
Center VESA
Bracket
H (x1)
Bracket Plate
I (x1)
Arm Support
Bracket
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
L (x1)
Pole Cable Clip
M (x4)
Arm Cable Clip
N (x1)
Pole Cap
S-A (x3)
M6x10mm
Thumbscrew
S-B (x2)
M4x5mm
Screw
S-C (x1)
M8x50mm
Screw
S-D (x2)
M8 Washer
S-E (x1)
M8 Nut
K (x1)
Grommet Plate
S-F (x4)
M6x27mm
Screw
S-G (x3)
M6x16mm
Flathead Screw
S-H (x1)
M5x16mm
Flathead Screw
M-A (x12)
M4x12mm
Screw
M-B (x12)
M4x16mm
Screw
M-D (x12)
M5x16mm Screw
M-E (x12)
M5 Washer
M-F (x12)
Spacer
T-A (x1)
4mm Allen
Wrench
T-B (x1)
6mm Allen
Wrench
T-C (x1)
Wrench
M-C (x12)
M5x12mm
Screw
S-I (x2)
M8x42mm
Screw

3
ASSEMBLY STEPS
OPTION A: Clamp Installation
Attach Upper Clamp (B1) to Pole (A) using the
M6x16mm Flathead Screws (S-G) and 4mm Allen
Wrench (T-A). Peel the protective lm o of So
Pad (J) and place it onto Upper Clamp (B1).
Separate Clamp (B) into Upper Clamp (B1) and Lower Clamp (B2) using 4mm Allen Wrench (T-A).
OPTION B: Grommet Base Installation
Remove the screw from the top of Lower Clamp
(B2) using a Phillips screwdriver, and set aside
Clamp Bolt (B3) and Support Plate (B4). Cut
So Pad (J) along the perforated lines. Peel the
protective lm o of So Pad (J) and place the
pieces onto Grommet Plate (K) as shown below.
TOOLS NEEDED
15.4lbs
Per Monitor
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
STEP 1
B
T-A
B1
B2
T-A
B1 S-G
A
J
B2 B3
J
K
B4

4
STEP 2 (Continued)
OPTION A: Clamp Installation
For thinner desktops (10-50mm), re-attach
Lower Clamp (B2) to Upper Clamp (B1)and
tighten the screws using the 4mm Allen Wrench
OPTION B: Grommet Installation
If not using an existing through-hole, using a
10mm (⅜”) drill bit, drill through the desktop at
least 2” away from the edge. Attach Pole (A) and
Grommet Plate (K) to the desktop using Support
Plate (B4) and Clamp Bolt (B3) as shown below.
B2
B1
T-A
A
K
B4
B3
For thicker desktops (40-85mm), disassemble
Lower Clamp (B2) using a Phillips screwdriver
as shown below. Flip the L-bracket over and
reassemble. Then re-attach Lower Clamp (B2) to
Upper Clamp (B1) and tighten the screws using
4mm Allen Wrench (T-A). Tighten the clamp
assembly to the desktop.
B1
T-A
B2

5
STEP 4
Slide Side VESA Brackets (F) onto Arm Extensions (E). Tighten the screw on the back of Side VESA
Brackets (F) using 4mm Allen Wrench (T-A) to secure them in place. Install M4x5mm Screws (S-B) into
Arm Extensions (E) using a Phillips screwdriver.
STEP 5
Install the arm assembly onto Pole (A) and
tighten the screw on the back of Arm Support
Bracket (I) using 4mm Allen Wrench (T-A) to
secure it in place. Attach Pole Cap (N) to the
top of Pole (A).
Assemble Arms (D), Arm Support
Bracket (I) and Bracket Plate (H)
using M6x27mm Screws (S-F) and
4mm Allen Wrench (T-A). Secure
Arm Extensions (E) to Arms (D)
using M8x42mm Screws (S-I)
and 6mm Allen Wrench (T-B).
Mount Center VESA Bracket (G) to
Bracket Plate (H) using M8x50mm
Screw (S-C), M8 Washers (S-D),
and M8 Nut (S-E) with 6mm Allen
Wrench (T-B) and Wrench (T-C).
STEP 3
D
I
H
S-F T-A
E
S-I
T-B
G
S-C
S-D
S-E
T-C
F
E
T-A
S-B
AI
T-A
N

6
STEP 6
Assemble Arm Cable Clips (M) to Arms (D) and Arm Extensions (E). Attach Pole Cable Clip (L) to Pole (A).
STEP 7
Attach VESA Plates (C) to the back of the monitor using Screws (M-A through M-D) and Washers (M-E).
If needed, use Spacers (M-F).
STEP 8
Slide monitors with VESA Plates (C) onto Side VESA Brackets (F) and Center VESA Bracket (G). Use
M6x10mm Thumbscrews (S-A) to secure them in place.
M
D
E
L
A
C
F
G
S-A

7
STEP 9
Manage cables using Arm Cable Clips (M) and Pole Cable Clip (L).
STEP 10
Adjust tilt, height, and horizontal orientation using Allen Wrenches (T-A and T-B) as shown below.
Store Allen Wrenches (T-A and T-B) in Pole Cable Clip (L).
M
L
T-B
T-B
L
T-B
T-A
T-A

LAST UPDATED: 01/31/2022
REV1
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303