Vogue 360172 Wiring diagram

360172/360173
Washing Machine And Dryer All In One
10kg Front Loading Vogue

2
5
7
washer-dryer
9
Troubleshooting guide 12
10
3

1
Safety Notices Before Use
Read and understand thoroughly these safty instructions before use.
The items indicated here are very important safety precautions,which
must be followed .We cannot be held liable for damage caused by
non-compliance with the warning and safety instructions of resulting
from incorrect use of operation.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical sensory or mental capablilities of lack of experience and knowledge if they have been
given supervison of instruction concerning used of the appliance in a safe way and understand
the hazards involved.Children shall not paly with appliance.Cleaning and user maintenance
shall not be made by children without supervision.Children of less than 3 years should be kept
away unless continuously supervised.
WARNING
Technical safty
Before setting the washer-dryer,check it for any externally visible damage.
Do not install or use a damaged washer-dryer .
Before connceting the washer-dryer,ensure that the connection data on the
plate(voltage and current)match the electricity supply.if in any doubt,consult a
qualifiled electrician.
The electrical safety of this washer-dryer can only be guaranteed when
continuity is complete between it and an effective earthing system which complies
with current local and national safety regulations.It is most important that this basic
safety requirement is present and regularly tested,and where there is any doubt the
household wiring system should be inspected by a qualified electrician. The manufacturer cannot be
heldliable for the consequences of an inadequate earthing system.
Unauthorized repairs could result in unforeseen dangers for the user,for which manufacturer can not
accept liability. Repairs should only be undertaken by an approved service technician.Ensure current is not
supplied to the machine until after maintenance of repair work has been carried out.
If the connection cable is damaged or broken, it must only be replaced by an approved service technician
to protect the user from danger.
Faulty components must only be replaced by genuine manufacturer original spare parts.Only when these
parts are fitted can the saftey standards of the machine be guaranteed.
THIS WASHER-DRYER MUST BE EARTHED.
Correct use
Do not connect the washer-dryer to the mains electricity supply by an extension lead.Extension
leads do not guarantee the required safety of the appliance.
To avoid the risk of personal injury of damage the washer-dryer,do
not install it in place where it is damp and where it suffers from rainfall.
Do not install the washer-dryer in place where if suffers from the sun
directly,in which plastic or components will be damaged .It will be shortened
the life of your washer-dryer .
Do not install the washer-dryer in place where temperatures below freezing
may occur.Frozen hoses may burst or split.The reliability of the elecronic control
unit may be impaired at temperatures below freezing point.
Do not shoot the wash with water when you clean it.er-dryer
Keep the wash away from fire or heat sources.er-dryer
Safety Notices Before Use
Before using the wash for the first time,check that the transit bolts at the rear of the machine er-dryer
have been removed.During spinning,transit bolts which is still in place may result in damage to both the
machine and adjacent furniture or appliances.
Turn off the tap if the machine is to be left any length of time (e.g.holiday),especially if there is no floor
drain(gully) in the immediate vicinity.
Take care to ensure that foreign objects(e.g.nails,pins,coins,paper clips) do not find their way into the
machine with the laundry.These may damage components of the machine (e.g.drum),which in turn can
result in damage to the laundry.
Do not wash water-repellent things(e.g.raincoats) with wash .er-dryer
Only remove laundry from the wash once the drum has stopped turning.Reaching into aer-dryer
moving drum is extremly dangerous and could result in injury.
Safety with children
Keep children away from the wash at all times.To avoid the er-dryer
risk of injury do not allow children to play on or near it or to play with its
controls.Supervise children whilst you are using it.
Older children may only use the wash if its operation haser-dryer
been clearly explained to them and they are able to use it safety,
recongnising the dangers of misuse.
For machine with a "prothole"door,remember that the porthole glass
will be hot when washing at very high temperatures.Do not let children
touch it.
Unscrew the drain pump filter to let water run out when the
machine is not used for a long time.
Parts and features Before Use
2
Connection Cable
cold water inlet valve
Door glass
Door seal
Drainage pump damper

Parts and features Before Use
Backout packing
Remove all the packing(include the foam base) or the vibration
and noise may occur.
Dispose all the wrappage safety and keep them out of the
reach of children.Danger of suffocation!
It is normal that water drops appear on the packing plastic
bag and the door glass,which are resulted from the water
left in the tub for checking out.
Accessories
Make sure that you have received all of the items shown below.
“U” piece
Removing transit bolts
Remove all the transit bolts at the back of the machine with tools.
Plug the holes with the transit bolts caps supplied.
Strong vibration,noise or failures may occur if hte transit
boltsare not removed.
The drawing of machine in the manual is only use for instruction.
It may be vary from the model you buy.
Keep the transit bolts for future transportation.whenever the machine is
transported,the transit bolts must be refitted.
Installation Before Use
Installation place requirement
A concrete floor is the most suitable installation surface for a washer-
dryer,being far less prone to vibration during the spin cycle than
wooden floorboards or carpeted surface.
The machine must be level and securely positioned. The distance
between the machine and wall must be more than 10 cm .
To avoid vibrations during spinning.the machine should not be
installed on softfloor coverings.
Level adjustment
The machine must stand perfectly level on all four feet to ensure
safe and proper operation.Incorrect installation may increase
electricity and water comsuption and may cause the machine to
move about.
To do these when the machine is not level:
Using the spanner turn locknut in clockwise direction. Then turn
locknuts together with adjust feet to unscrew.
To avoid vibrations during spinning.the machine should not be
installed on softfloor coverings.
To avoid vibrations during spinning.the machine should not be
installed on softfloor coverings.
Vibration and noise may occur if the locknuts do nut sit firmly up
against the houses.
Drain hose connection
1.Direct into a sink
If the outlet spigot has not been used before,remove any blanking plug that may be in place.
If required,the drain hose can be extended to a length of 4 m.
Push the drain hose onto the spigot and secure with a clip if required,ensure a loop is formed in
the drain hose to prevent waste from the sink entering the wash .er-dryer
Loop
2.Connected securely to a standpipe
Firstly form a hook in the end of the drain hose using “U” piece supplied.
Place the drain hose into your standpipe,which should have an internal diameter of apporoximately
30mm thus ensuring there is an air break between the drain hose and standpipe.
When discharging into a standpipe ensure that the top fo the standpipe is no more than 90cm and
no less than 60cm above floor level.
“U” piece
supplied
34
30cm
60cm
90cm
Installation Before Use

Installation Use process
Water inlet connection
Connect the inlet hose supplied with the machine to a tap with a 3/4" thread.
Do not use previously employed hoses.
Installation should comply with local water authority and building regulations ‘ requirements.
Connect a water supply to the inlet valve at back of the machine.Follow the indication of
the picture below to complete the connection.
inlet hose for cold water with a white nut
inlet valve for cold water
Functions of the control panel Use process
5
The operation panel.
2.Dry
Select the time for drying. If you want to dry laundries after washing, select this button.
Press the button repeatedly to select drying times orderly: 0,60,90,120,150,180,210,240,270,
300,330 ,360,390 minutes. The required lamp will light up for identification.
3
5
6
6
6
You can press this button for 3 seconds to pause wash cycle and add clothes, but if the water
level or the temperature of the drum is high, the door will not open.
The selectable options and functions of different programs
Program
Weight
(kg)
Time
(min)
Drum Clean
Spin
Rinse/Spin
Quick
Dry: the logo will be bright when selected the dry function, the logo will be flicked
during the drying process.
when
10
10
7
6
4
10
0
10
10
5
3.5
1
6
4
1
76
197
49
131
66
99
109
11
16
51
18
42
60
35
60
Icon explanation
Temp
Rinse times
Spin speed(rpm) Dry time(min)
0/60/90/120/150/180/210/240/270/300/330
0/20/40/60/95
0/20/40/60/95
20
95
0/20/40
0/20/40/60
60/95
0/20/40/60
0
0
0/60/90/120/150/180/210/240/270/300/330
0/60/90/120/150/180/210/240/270/300/330
0/60/90/120/150/180/210/240/270/300/330
0/60/90/120/150/180/210/240/270
42
60/90/120/150/180/210/240/270/300/330/360/390
42
35
35
2/3/4/5
2/3/4/5
2/3/4/5
2/3/4/5
3/4/5
3/4/5
2
1/2/3/4
2/3/4
2/3/4
2/3/4
0/400/600/800/1000/1200/1400
0/400/600/800/1000/1200/1400
0/400/600/800/1000/1200
0/400/600/800/1000
0/400/600/800
0/400/600/800/1000/1200
600
0/400/600/800/1000/1200/1400
0/400/600/800/1000/1200/1400
0/400/600/800
0/400/600/800/1000/1200
0/400/600/800/1000/1200
0/1400
0
6
6

When washing cycle is finished, the machine will change into standby mode.
And the power will be off after 10 minutes without any control on the control panel.
Programme chart
The machine is fitted with a balance control device, which ensures the machine is stable
during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed
in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen
several times before the unbalance disappears and normal spinning can resume. If, after
15 minutes, the laundry is still not evenly distributed in the drum, the machine will not spin.
In this case, redistributed the load manually and reselect the spin programme.
8
3. Place the drain hose well.
1. Sort the laundry by colour and by care label. Most garments have a textile
care label in the collar or side seam.
2. Make sure all the pockets are empty, Foreign objects (e.g. nails, coins, paper
clips, etc.) can cause damage to garments and components in the machine.
3. Close any zips, fasten hooks and eyes etc before washing.
4. Dark textiles often contain excess dye and should be washed separately several times
before being included in a mixed load. Always wash whites and coloureds separately.
5. Badly soiled areas, stains etc. should be pre-treated with liquid detergent,stain removers etc.
6. Turn over the clothes which pill easily and is with woolen surface before putting them
into the machine.
Unfold the laundry and load loosely in the drum. Mixing both large and small items
gives better wash results and also helps distribute the load evenly during spinning.
The most efficient use of energy and water is achieved when a full load is washed.
However, do not overload as this causes creases and reduces cleaning efficiency.
Make sure that no garments are caught between the door and the seal.
It can remove the water which is left in the tub because of manufacturer’s checking out.
,turn the knob to position “D ” and press aily “start/pause”.
It is recommended to use low foaming powder for all washing temperature programs.
How to use washer-dryer
Use process
7
1. Open the drawer and add adequate detergent into main wash
compartment marked “ ” or “ ”.
2. Add the fabric softener into compartment marked “ ” or “ ” .
Do not exceed the maximum level mark.
3. Add the detergent into the pre-wash compartment marked
“ ” or “ ”according to the programme you select.
4. Close the drawer.
The right amount to dispenser will depend on the following:
The quantity of laundry
The soiling level of the laundry
Main wash compartment
Fabric softener compartment
Pre-wash compartment
- Normally soiled: visibly dirty and/or just a few slight stains.
- Heavily soiled : visible dirt and stains and/or dried on soiling.
The water hardness level.
- Lightly soiled : no visible dirt or stains. Possibly slight body odour.
1.Turn on the water tap, and connect the power.
2.Open the door, and put the cloth into the drum one by one.
3.Close the door, and put suitable amount of detergent and fabric softener into the
dispenser, then close the drawer.
4.Choose a programme you need by turning the knob .
5.Press the “Temp.” button and select a wash temperature.
6.Press “ Start/Pause” button to start the washer-dryer.
7.When the cycle is finished, there is a warning tone sounds.
Fabric
Programme
Cottons, linens or cotton mix fabrics, e.g. towelling, underwear, T-shirts etc.
This program can be used for rinsing items which can be washed in a
Cotton program. Do not add any detergent.
Separate spin for cotton and linen items
Cottons, linens or cotton mix fabrics, e.g. table linen, underwear, T-shirts etc.
Washing clothes at
95℃ , which would help for sterilization and disinfection.
Quick
.Cottons, linens or cotton mix fabrics
This program can be used to remove the peculiar smell and folds of clothes.
This program is used to clean the drum. Don’t put any clothes into the
drum while running this program.
New clothes or a small amount of clothes which is not that dirty.
This program can be used to dry a small amount of clothes.
Washing symbol
Synthetic or mixed fabrics, underwear, coloured garments, non-shrink shirts.
Note: 1.These kinds of clothes should not be used for the dry program: clothes
has the logo “ ”,woollen clothes, silk, clothes contains leather or foam
rubber, clothes washed by volatile solvent such as detergents and gasoline.
2.For drying the clothes washing by hands, please choose the highest spin
speed to spin the clothe , then choose the suitable dry program to dry the
clothe.
3.The clothes using to dry should not more than the weight marked in the
table on page 6.
4.The drying must use the tap water ,so be sure the tap is be opened and
the water is cold.
5.If drying to much clothes at one time, the drying effect is not ideal and the
time may be long. If the clothes is not fully dry, please dry the clothes in
several parts.
6.For preventing burns, the machine will reduce the temperature of the drum
before the dry program ended. It is normal that the time stops reducing on
the display. Do not stop the machine during the cooling, since the temperature
of the drum is still high, the door will not be opened.
7.If you select the dry function, the default spinning speed and time will be
the max. You can select the speed and time by yourself, according to the
clothes washed.
8.The program “Refresh” is using the dry function to refresh the clothes, so please
make sure the water tap is open and don not put any detergent or softener into
the machine.
Drum Clean
Spin
Rinse/Spin
This program can be used to dry clothes.
Clothes with large volume
Down jacket or down coat.
This program can be used to wash and dry a small amount of clothes.

Cleanness and maintenance
After Use
Disconnect the machine from the mains electricity supply and withdraw the plug from
the socket before cleaning the machine.
The wash must not be hosed down.er-dryer
Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a well wrung-out
cloth. Wipe dry with a soft cloth.
Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.
These might damage plastic surfaces and other components because of the chemicals
they contain.
Clean the drum every 3 months by using the “ ” program.
Cleaning the drawer
Remove detergent residues regularly. Clear the drawer following these:
Pull out the drawer until a resistance is felt. Press down the release
catch and at the same timepull the drawer right out of the machine.
Remove the siphon from compartment and clean it.
Clean the dispenser using a brush and warm water.
Use pointed nose pliers to with draw the plastic filter.Clean, put back and secure. These filter should
be checked every 6 months or so, or more often if there are frequent interruptions to the water supply.
The filter should be
cleaned every 2
months or so, or
when thereis fault
that the “E03” is on
the screen.
Cleaning the drawer housing
Use a bottle brush to remove detergent residuesinside the drawer housing.
The filter must be
put back in place
after cleaning.
Important:
If the machine is exposed to temperatures below 0°C, certain precautions
should be taken.
1. Turn off the water tap.
2. Unscrew the inlet hose.
3. Unhook the drain hose from the rear support and position the end of this
hose and that of the inlet hose in a bowl. Run the spin programme.
4. Disconnect the appliance.
5. Screw the inlet hose and reposition the drain hose.
6. When you intend to start the machine up again, make sure that the room
temperature is above 0°C.
1. Disconnect the machine from
the mains electricity supply and
open the lower cover with a
screwdriver.
2. Place a container under
the pump.Unscrew and r
emove the filter.
3. Clean the filter carefully
When the machine is started, the door lock is locked though you press the “Start/Pause” button.
Press the “power” button to switch off the machine and the door lock is unlocked in two minutes.
When the temperature inside the drum is above 53℃, the door lock is locked.
When the water is above a certain level, the door lock is locked.
When the washing cycle is finished, the door lock is unlocked after two minutes.
Important:
Do not try to open the door when the washing cycle is not finished or power supply is cut off
during the washing cycle, because the temperature may be high and you may be scalded.
10
9
Eelctric Diagram
Drum Clean
Water_Heater
Door lock
Inverter Board
LED MODULE
EARTH
Air Inlet NTC1(NC)
S2 VH-5A
Air Outlet NTC2
S1

Technical parameters
Note:
Data can vary from the nominal values given depending on water presurewater hardness,water
inlet temperate,room temperature,type and volume of load,fluctuations in the electricity supply
and any extra options selecetd.
360172/360173
Modle
Parameter
Power
Washing/dry capacity
Rated power
Water pressure
Out dimenssion(WxDxH)mm
Net weight /
gross weight 70kg/75kg
595X665X845
2000W
10kg/6kg
220V-240V~/50Hz
Choose the program set the washing temprature to
Washing cycle:
Drying cycle: Choose the program”Dry” ,set the spin speed to 1400rpm , select
the drying time to 360 (the display will show 6:00 seconds later).
11
1.
it is secure.
Check the connection and ensure
2. Change the temperature sensor.
1. The connection between the
and temperature sensor is not secure.
wire
2. The temperature sensor is damaged.
1. Check the connection and ensure
it is secure.
2. Change the heating tube.
1. The connection between the heating
tube and wire is not secure.
2. The heating tube is damaged.
1. Check the connection and ensure
it is secure.
2. Check if the machine is overloaded.
Switch off the machine, and retry
when the motor becomes cool.
3. Change the motor.
1. The connection between the
motor and wire is not secure.
2. The motor is protected because
of over-heat.
3. The motor is damaged.
1. Change the water inlet.
2. Check the connection and ensure
it is secure.
3. Change the water sensor.
1. The water inlet valve is damaged.
2. The connection between the water
sensor and wire is not secure.
3. The water sensor is damaged.
Possible Cause
The machine
fills overtime.
There is a Door
lock alarm.
1. The water tap is not open.
2. The drain hose is put down.
3. The water inlet valve is damaged.
1. Open the water tap.
2. hook up the hose.
3. Change the water inlet valve.
“E01” is on the
screen.
Problem Error Code
The machine
drains overtime.
Water overflows
the machine.
/ Water sensor
works abnormal.
The motor does
not work.
There is a
heating tube
fault.
There is a
temperature
sensor fault.
1. Check the drain hose.
2. Clean the filter.
3. Check the drainage system
and clean it.
1. The drain hose is squashed or kinked.
2. The drain pump filter is block.
3. The drainage system pipes
are blocked.
1. Lock the door well.
2. Put the garment into the drum.
3. Change the door lock.
1. The door is not locked well.
2. garment is caught between the
door and the seal.
3. The door lock is damaged.
“E02” is on the
screen.
“E04” is on the
screen.
“E03” is on the
screen.
“E05” is on the
screen.
“E06” is on the
screen.
“E07” is on the
screen.
long cooling “Edc” is on the
screen.
1 .The dry cooling time is over ten 1.Check the tap and ensure it’s open.
Inverter fails
to start “E09” is on the
screen.
1. The connection between the
inverter and wire is not secure.
2. The inverter is damaged.
1. Check the connection and ensure
it is secure.
2. Change the inverter
3. restart the machine
minute at the end of drying. 2.Check the water and ensure it’s cold.
Marking explanation
VVolt
WHz
Watt Hertz
Alternating current
risk of fire
~
Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a
tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates
heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or
storing oil-affected items can prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by
hair care products be placed in a tumble dryer they should first be washed in hot water with extra
detergent - this will reduce, but not eliminate, the hazard.
12