Volfoni ACTIVHUB CINEMA User manual
ACTIVHUB CINEMA
Model : VPES-01000
Document : MUV120135-B00 ActivHub_Cinema_User_Manual
Compatible with EDGE1.2 glasses (VPEG-01100)
I.
PRESENTATION
1.
General presentation
2.
Composition
II.
PRODUCT DESCRIPTION
1.
IR emitter
2.
Tester
3.
Synchronizer
III.
FASTENING
IV.
CONNECTION&SYNCHRONIZATION
V.
WARRANTY
VI.
REGULATORY STANDARDS
VII.
CONTACTS
1. GENERAL PRESENTATION
The ActivHub Cinema kit allows easy integration in less than 30
minwith existing digital theaters using a standard screen
The system is compatible with EDGE1.2 glasses provided by
Volfoni.
The complete system includes following parts :
ActivHub Cinema (1 synchronizer + 2 IR emitters)
1 SUB-D37/SUB-D9 cable
2 SUB-D9/SUB-D9 cables
2 Universal mount fastening
1 Power supply adapter
1 Power supply cable
1 Activ 3D glasses tester with 3 batteries
1 User guide
Systems are provided with a new universal mount making
installation even faster (installation process is the same
as described in section III) :
IR EMITTER
+ fixing
+ wire
TESTER
S
Y
N
C
H
R
O
N
I
Z
E
R
+ power cord
+
G
P
I
O
s
y
n
c
h
r
o
n
i
z
e
r
cable
SYNC IN(DB9)
Before starting, please check if the following parts are included in
the package.
1.
IR EMITTER
Long Range IR Emitter
L
o
n
g
R
a
n
g
e
I
R
E
m
i
tt
e
r
V
A
I
K
-
0100
i
s
a
c
o
m
p
a
c
t
a
n
d
p
o
w
e
r
f
u
l
un
i
t
.
T
h
e
emitter,withmanybuilt-ininfraredLEDs,allowscoveragealltypesof theater
rooms, regardless of the number of seats. 4 emitters can be linked up.
T
h
a
n
k
s
t
o
i
t
s
li
g
h
t
w
e
i
g
h
t
de
s
i
g
n
,
V
A
I
K
-
0100
e
nh
a
n
c
e
s
t
h
e
h
e
a
t
d
i
ss
i
p
a
t
i
o
n
(LEDlifeprotection).It isprovidedwithauniversalmountingheadforsecurity,
and is easy to install. It is simple to target the screen with the emitter laser pointer.
Please do not put the emitter in front of the audience.
Emitter at a Glance
Mounting Hole Power LED
Laser: Max Output: 0.5mW, Wavelength: 650 nm± 10
Dimension:
361 mm x 70 mm x 44 mm
W
A
R
N
I
N
G
:
T
h
e
l
a
s
e
r
p
o
i
n
t
e
r
o
f
t
h
i
s
e
m
i
tt
e
r
e
m
i
t
s
C
l
a
ss
III
A
l
a
s
e
r.
PleaseDO NOT stare into beam or view directly with optical instruments.
2.
TESTER
Battery Room
Active 3D Glasses VAIK-0300 is a handy unit to be carried by a cinema
technician to check performance of 3D glasses. Turn on the power, then
the tester emits low rate IR signal to activate 3D glasses. Working 3D
glasses will then show a flickering.
Additional Specification
Power supply: 3xAA batteries
IR SignalLED
Power LED
Power Switch
3. SYNCHRONIZER
Power Module
Multi-function Distribution Module
Themulti-function DistributionModuleisa unit specially designed for mid
size and large digital 3D cinemas. This unit is plugged into the digital
p
r
o
j
e
c
t
o
r
a
n
d
r
e
c
e
i
v
e
s
f
r
a
m
e
s
y
n
c
h
r
o
n
i
z
i
n
g
s
i
g
n
a
l
v
i
a
G
P
I
O
(
D
B
-
37
)
.
I
t
e
x
t
e
n
d
s
to four DB-9 emitter outputs. It also supports the extension of the Distribution
Module thanks to a DIN-3 cable, that simplifies cinema wiring. Each port is
equipped with an error diagnosis indicating LED.
II.
PRODUCTDESCRIPTION
LOC AL IR EMI TTE RS
LASER POINTER
O N OFF
LOCAL IR EMITTERS
O N OFF
SETUP FRA ME SYNC
Laser Pointer ON/OFF
Local IR Emitters ON/OFF
PO WER
OUTPUT TO IR EMITTERS
QUIC K FR AME SYN C
ON OFF
EYE ROT ATI ON
O N OFF
Frame SYNC Setup Switch
Eye Rotation Switch
CH1 CH2 CH3
CH4
FRAME SYNC FROM PROJECTOR
Distribution Module Extension Port
P
o
w
e
r
I
n
p
u
t
P
o
r
t
Power Switch
CH1,2,3,4SYNCPort toIREmitter
F
r
a
m
e
S
Y
N
C
F
r
o
m
P
r
o
j
e
c
t
o
r
Switch Function Description:
LASER POINTER: ON/OFF switch for each emitter laser / If
synchronization cable connected to synchronizer and if a signal is
detected, laser pointer do not work
LOCAL IR EMITTERS:
N/A
SETUP FRAME SYNC: Switch on to detect frame synchronizing range
EYE INVERSION: Switch left/right eye image
POWER: Turn ON/OFF the power of the Distribution Module
I
n
d
i
c
a
t
i
o
n
LED
status
definition:
POWER: LED lights come on (fixed red) when power is on, otherwise
light is out
Channels 1/2/3/4 : Off if emitter not connected / Fixed green when
emitter connected and signal from projector detected by synchronizer
LEDs from emitters: fixed red when emitter connected to synchronizer
SETUP FRAME SYNC:
Off in 2D mode / Fixed or blinking green
depending on 3D mode settings from projector
FRAME SYNC FROM PROJECTOR:
LED light on (fixed or green blinking)
when signal from projector is detected by synchronizer
Basic Specification:
Power Input:24VDC, 3A
D
e
f
a
u
l
t
S
y
n
c
I
n
:
P
I
N
9
(+)
and
PIN28
(-)
o
f
G
P
I
O
(
D
B
-
37
)
Dimension
:106 mm x 36 mm x 23 mm
WALL FASTENER
Before installing the emitter in the front of the screen, make sure you
have all theneeded tools and the instruction manual. This wall fixing
part is provided with all the screws and wall anchors you might need.
Follow the instructions to fasten this kit.
1 2 3 4 5
Parts
Qty
2
2
1
1
1
Product description
Mounting plate
Screw covers
Extension
Adjusting Knuckle
Emitter plate
Wall types and holes sizes
III.
FASTENING
STEP1
use the wall base to
mark each holeto drill
with a pencil.
INSTALLATION
STEP2
drilltheholeswiththegivenbit
(forwoodsurfaceonly)
(Forsolid concreteanddrywallonly)
STEP
Insertwallanchors
STEP4
tightly screw the base to the wall
STEP5
assemble the arm to the base
andthenscrewtheemitteronit
IV.
Digital Projector
GPI/O(DB37-F) GPI/O Extension
(DB37-M)
Power Adapter
24VDC/3A PowerAdapter
24VDC/3A
Distribution Module Distribution Module(Extension)
DIN-3
DIN-3 Extension Cable
Distribution Module
Cable
DB-9
IR Emitter 3
IR Emitter Cable
DB-9
DB-9
IR Emitter 2
IR Emitter 1
TECHNICAL SPECIFICATIONS
Fall time
Rise time
Contrast
Transmission in the clear state
Chromaticity
Standard parameters
E
D
G
E
T
M
1
.
2
Double flash (4.2)
500µs
1.5ms
> 200 (no ghosting)
33%
Color correction not mandatory
Dark time:
500
Delay:
-320
Triple flash (6.2) Dark time:
800
Delay:
-320
Weight
Battery
Autonomy
56g
Disposable
800 hours
Warning: Depending on your equipment and the room configuration,
you may have to adjust these parameters. We recommend that you confine
the setup of 3D parameters and color adjustments directly to integrators.
Forfurtherinformationpleasevisitourwebsite
www.volfoni.com
,
or send us an email to support@volfoni.com.
These parameters are for information purpose only. They may
be adapted if necessary.
V. WARRANTY
The ActivHub Cinema is warrantied to the original purchaser for three
years according to local legislation. Infra-red emitters and cables
should be returned in original box along with original proof of
purchase. Infra-red emitters which are broken or scratched are not
covered.
Emitters & Synchronizers : « Volfoni does not cover uninterrupted or
error-free operation of the product under warranty ».
VI. REGULATORYSTANDARDS
European Union –Disposal Information
According to local laws and regulations your product should be
disposed of separately from household waste. When this product
reaches its end of life, take it to a collection point designated by
local authorities.
Some collection points accept product for free. The separate
collection and recycling of your product at the time of disposal will
help conserve natural resources and ensure that it is recycled in a
manner that protects human health and the environment.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interferences that may cause
undesired operation.
CE Certification
This device complies with CE Certification.
Electrical Safety (IEC 60950-1)
This device complies with IEC 60950-1
Table of contents
