vYSoo MR600 User manual

Mobile Router MR600
User Guide
HANTZ + PARTNER
The Upgrade Company! www.hantz.com
www.hantzundpartner.com/3grouter

2
1. Connections and LEDS
The following pictures show you various connectors and status LED indicators on the MR600 Mobile Router.
Power LED
Status LED
PC Card Slot
www.hantzundpartner.com/3grouter

3
Default Button
Ethernet LAN Port
Power Jack
USB Port (Optional)
WiFi Secure
Set Button
www.hantzundpartner.com/3grouter

4
2. Getting Start
Before getting started, make sure your 32-bit PC Card or USB Data Card supports and compatible with
broadband service. (Subject to services and Service terms available from your carriers).
STEP 1 : Insert Data card to PC card slot or USB Port
ou or
www.hantzundpartner.com/3grouter

5
STEP 2 : Plug in power adapter
When connect the power adapter to back panel power Jack, the power LED turns ON
to indicate power has been applied.
Power LED
www.hantzundpartner.com/3grouter

6
STEP 3 : Check Status LED
When power on MR600, it will auto-detect and initial your date card. Status LED Will Flash ON and OFF One by one
when MR600 performs initialization and Internet connection process. MR600 will be auto-configured properly for
your Internet Service Account. This process takes a few minutes.
When complete, the status LED illuminates in GreenPlease refer the below Status
LED Activity table for each State
www.hantzundpartner.com/3grouter

7
3. Congratulation! You have Connected With Wireless Internet
MR600 is PnP for your Data card. It configures and enables wireless LAN automatically. If you have any
problem or need more advanced feature setting, please refer to chapter 5 for more details.
4. Advance Setting through Web page
STEP 1 : Connect your PC/Notebook to MR600
www.hantzundpartner.com/3grouter

8
STEP 2 : Open your web browser such as IE or Netscape and type Press Enter http://192.168.1.1 in address bar.
STEP 3 : Login Mobile Router
• Enter your user name in the Username box. The default user name is admin..
• Enter your password in the Password box. The default password is admin.
• Click OK.
www.hantzundpartner.com/3grouter

9
STEP 4 : Once logged in the following screen is displayed
STEP 5 : Click WWAN for WAN Networking Setting
www.hantzundpartner.com/3grouter

10
Note : The WAN fields may not be necessary for your connection. Information on this page will only be used
when your service provider requires you to enter User Name and Password to connect to the broadband
Network.
Please refer to your Data Card documentation or service provider for addition
Note : The WAN fields may not be necessary for your connection. Information on this page will only be used
when your service provider requires you to enter User Name and Password to connect to the broadband
Network.
Please refer to your Data Card documentation or service provider for addition
Dial Number The default is *99#. This field should not be altered unless required
by your service provider.
User Name Enter the new User Name for your Data card connection.
Password Enter the new Password for your Data card connection.
APN Enter the name of your service Provider Network.
www.hantzundpartner.com/3grouter

11
STEP 6 : Click WLAN for wireless network setting
www.hantzundpartner.com/3grouter

12
STEP 7 : Click LAN for Local Network setting
SSID Enter your SSID name in the field provided. SSID names can contain up to 32 ASCLL characters.
Encryption You may select from two levels of encryption to secure your wireless Network : None or WEP.
Key Length Two levels of wireless encryption are available64 bits and 128 bits
Key Type Two type of WEP KeyHex or ASCII. choose the proper one for key Setting.
Key1~Key4 You can enter the WEP key by manually and choose Key1~Key4 for enable.
www.hantzundpartner.com/3grouter

Note : When DHCP server IP address range is set , it must be assured that there is no other
device in the network to use the IP address located in this address range , such as printer
server , file server , etc . Otherwise there is
Note : When DHCP server IP address range is set , it must be assured that there is no other
device in the network to use the IP address located in this address range , such as printer
server , file server , etc . Otherwise there is
DHCP Server This setting is used to configure MR600’s Dynamic Host Configuration Protocol
(DHCP) server function. MR600 can be used as a DHCP server for the internal
LAN network. The DHCP server automatically assigns an IP address to each
computer in the LAN network. If you choose to enable MR600 s DHCP server
option, you must configure all of PCs in the LAN network to connect to this DHCP
server (MR600), and make sure there is no other DHCP server on your network.
Start IP Address Enter the values for start IP address. The default start IP address is 192.168.1.100
End IP address Enter the values for end IP address. The default end IP address is 192.168.1.200
IP address The IP Address of the LAN. The default IP address is 192.168.1.1
Net mask The subnet mask of the LAN
Österreich:
Tel.: 01 / 58 55 430
Fax: 01 / 58 55 460
Deutschland:
Tel.: 0761 / 59 21 00
Fax: 0761 / 58 52 28
Schweiz:
Tel.: 061 / 27 311 - 31
Fax: 061 / 27 311 - 39
HANTZ + PARTNER
The Upgrade Company! www.hantz.com