Warren SANDPIPER TA3 Parts list manual


TA3
Metallic Construction
Design Level 2

A Unit of IDEX Corporation
800 N. Main St.,
Manseld, Ohio 44902 USA
Telephone [phone]
Fax [phone]
SANDPIPERPUMP.COM
©2017 Warren Rupp, Inc.
Certied Quality
ISO 9001 Certied
ISO 14001 Certied
SERVICE & OPERATING MANUAL
Original Instructions
1: SPECS2: INSTAL & OP3: EXP VIEW4: WARRANTY

sandp ipe rpu mp.c om
ta3mdl2sm-rev0917
Model TA3
IMPORTANT
Read the safety warnings and instructions in this manual
before pump installation and start-up. Failure to comply with
the recommendations stated in this manual could damage the
pump and void factory warranty.
When used for toxic or aggressive uids, the pump should
always be ushed clean prior to disassembly.
Airborne particles and loud noise hazards. Wear eye and ear
protection.
Before maintenance or repair, shut off the compressed air line,
bleed the pressure, and disconnect the air line from the pump.
Be certain that approved eye protection and protective clothing
are worn at all times. Failure to follow these recommendations
may result in serious injury or death.
When the pump is used for materials that tend to settle out
or solidify, the pump should be ushed after each use to
prevent damage. In freezing temperatures the pump should be
completely drained between uses.
Before pump operation, inspect all fasteners for loosening
caused by gasket creep. Retighten loose fasteners to prevent
leakage. Follow recommended torques stated in this manual.
CAUTION
WARNING
Nonmetallic pumps and plastic components are not UV
stabilized. Ultraviolet radiation can damage these parts and
negatively affect material properties. Do not expose to UV light
for extended periods of time.
In the event of diaphragm rupture, pumped material may enter
the air end of the pump, and be discharged into the atmosphere.
If pumping a product that is hazardous or toxic, the air exhaust
must be piped to an appropriate area for safe containment.
This pump is pressurized internally with air pressure during
operation. Make certain that all fasteners are in good condition
and are reinstalled properly during reassembly.
Take action to prevent static sparking. Fire or explosion can
result, especially when handling ammable liquids. The pump,
piping, valves, containers and other miscellaneous equipment
must be properly grounded.
Safety Information
Use safe practices when lifting
kg
RECYCLING
Many components of SANDPIPER®AODD
pumps are made of recyclable materials.
We encourage pump users to recycle worn
out parts and pumps whenever possible,
after any hazardous pumped fluids are
thoroughly ushed.
WARNING
The use of non-OEM replacement parts will void (or negate)
agency certications, including CE, ATEX, CSA, 3A and EC1935
compliance (Food Contact Materials). Warren Rupp, Inc. cannot
ensure nor warrant non-OEM parts to meet the stringent
requirements of the certifying agencies.
UNIVERSAL ALL AODD
ATEX compliant pumps are suitable for use in explosive atmospheres when the equipment is properly grounded
in accordance with local electrical codes. Pumps equipped with electrically conductive diaphragms are suitable for
the transfer of conductive or non-conductive uids of any explosion group. When operating pumps equipped with
non-conductive diaphragms that exceed the maximum permissible projected area, as dened in EN 13463-1: 2009
section 6.7.5 table 9, the following protection methods must be applied:
• Equipment is always used to transfer electrically conductive uids or
• Explosive environment is prevented from entering the internal portions of the pump, i.e. dry running
For further guidance on ATEX applications, please consult the factory.
Grounding ATEX Pumps

sa ndp ipe rpu mp.c om Model TA3 • 3
ta3mdl2sm-rev0917
Table of Contents
SECTION 1: SPECIFICATIONS .........................1
• Materials
• Dimensional Drawings
SECTION 2: INSTALLATION & OPERATION ...5
• Recommended Installation Guide
• Troubleshooting Guide
SECTION 3: EXPLODED VIEW ..........................8
• Composite Repair Parts Drawing
• Composite Repair Parts List
• Material Codes
SECTION 7: WARRANTY & CERTIFICATES . . 15
• Warranty
• CE Declaration of Conformity - Machinery
• ATEX Declaration of Conformity
MODEL SPECIFIC

sa ndp ipe rpu mp.c om
4 • Model TA3
ta3mdl2sm-rev0917
Materials
Material Prole: Operating
Temperatures:
Max. Min.
Conductive Acetal: Tough, impact resistant, ductile. Good
abrasion resistance and low friction surface. Generally inert, with
good chemical resistance except for strong acids and oxidizing
agents.
190°F
88°C
-20°F
-29°C
EPDM: Shows very good water and chemical resistance. Has
poor resistance to oils and solvents, but is fair in ketones and
alcohols.
280°F
138°C
-40°F
-40°C
FKM: (Fluorocarbon) Shows good resistance to a wide range
of oils and solvents; especially all aliphatic, aromatic and
halogenated hydrocarbons, acids, animal and vegetable oils.
Hot water or hot aqueous solutions (over 70°F(21°C)) will
attack FKM.
350°F
177°C
-40°F
-40°C
Hytrel®: Good on acids, bases, amines and glycols at room
temperatures only.
220°F
104°C
-20°F
-29°C
Neoprene: All purpose. Resistance to vegetable oils. Generally
not affected by moderate chemicals, fats, greases and many
oils and solvents. Generally attacked by strong oxidizing acids,
ketones, esters and nitro hydrocarbons and chlorinated aromatic
hydrocarbons.
200°F
93°C
-10°F
-23°C
Nitrile: General purpose, oil-resistant. Shows good solvent, oil,
water and hydraulic uid resistance. Should not be used with
highly polar solvents like acetone and MEK, ozone, chlorinated
hydrocarbons and nitro hydrocarbons.
190°F
88°C
-10°F
-23°C
Nylon: 6/6 High strength and toughness over a wide
temperature range. Moderate to good resistance to fuels, oils
and chemicals.
180°F
82°C
32°F
0°C
Polypropylene: A thermoplastic polymer. Moderate tensile
and ex strength. Resists stong acids and alkali. Attacked by
chlorine, fuming nitric acid and other strong oxidizing agents.
180°F
82°C
32°F
0°C
PVDF: (Polyvinylidene Fluoride) A durable uoroplastic with
excellent chemical resistance. Excellent for UV applications.
High tensile strength and impact resistance.
250°F
121°C
0°F
-18°C
Santoprene®: Injection molded thermoplastic elastomer with
no fabric layer. Long mechanical ex life. Excellent abrasion
resistance.
275°F
135°C
-40°F
-40°C
UHMW PE: A thermoplastic that is highly resistant to a broad
range of chemicals. Exhibits outstanding abrasion and impact
resistance, along with environmental stress-cracking resistance.
180°F
82°C
-35°F
-37°C
Urethane: Shows good resistance to abrasives. Has poor
resistance to most solvents and oils.
150°F
66°C
32°F
0°C
Virgin PTFE: (PFA/TFE) Chemically inert, virtually impervious.
Very few chemicals are known to chemically react with PTFE;
molten alkali metals, turbulent liquid or gaseous uorine and
a few uoro-chemicals such as chlorine triuoride or oxygen
diuoride which readily liberate free uorine at elevated
temperatures.
220°F
104°C
-35°F
-37°C
Maximum and Minimum Temperatures are the limits for which these materials can be operated.
Temperatures coupled with pressure affect the longevity of diaphragm pump components.
Maximum life should not be expected at the extreme limits of the temperature ranges.
Metals:
Alloy C: Equal to ASTM494 CW-12M-1 specication for nickel and nickel alloy.
Stainless Steel: Equal to or exceeding ASTM specication A743 CF-8M for corrosion
resistant iron chromium, iron chromium nickel and nickel based alloy castings for
general applications. Commonly referred to as 316 Stainless Steel in the pump industry.
For specic applications, always consult the Chemical Resistance Chart.
CAUTION! Operating temperature limitations are as follows:
Ambient temperature range: -20°C to +40°C
Process temperature range: -20°C to +80°C for models rated as category 1 equipment
-20°C to +100°C for models rated as category 2 equipment
In addition, the ambient temperature range and the process temperature range do not exceed the operating temperature range of the applied non-metallic parts as listed in the manuals of the pumps.
MODEL SPECIFIC UNIVERSAL ALL AODD
1: PUMP SPECS

sa ndp ipe rpu mp.c om Model TA3 • 5
ta3mdl2sm-rev0917
SERVICE AND OPERATING INSTRUCTIONS
This Warren Rupp Tranquilizer® is a completely automatic diaphragm tted
surge suppressor to reduce the ow and pressure pulsations in a pumping system
characteristic of reciprocating type pumps.
Principle of Operation: The Tranquilizer
uses a flexible diaphragm to separate a
liquid chamber from compressed air chambers. A rod connected to the
center of one diaphragm activates the air inlet and exhaust valves, which
automatically admit or exhaust air in the air chambers. This maintains the
diaphragms in mid-range of stroke for maximum surge suppression.
Installation: Locate the Tranquilizer in discharge piping as close as
possible to the pump. The unit will operate in any position. Connect air inlet
connection to full plant air supply line before the air regulator to pump. Not
to exceed 125PSI.
Service Instructions: When service is required, it is
important to MAKE CERTAIN THAT INLET AIR PRESSURE IS
DISCONNECTED. The diaphragms are serviced by simply removing
the hex nuts or v-band, and removing the center spool casting.
When Virgin PTFE diaphragms are used in conjunction with the elastomeric
diaphragms they are placed over the “wetted” sides of each elastomeric
diaphragm. Inlet and exhaust air valves are located externally for easy
access and service.
Warranty: This unit is guaranteed for a period of ve years against defective
material and workmanship.
Before surge suppressor
operation, inspect all
gasketed fasteners for
looseness caused by
gasket creep. Re-torque
loose fasteners to prevent leakage. Follow
recommended torques stated in this manual.
CAUTION
IMPORTANT
Read these safety warnings
and instructions in this
manual completely, before
installation and start-up
of the pulsation dampener.
It is the responsibility of the purchaser to retain
this manual for reference. Failure to comply with
the recommendations stated in this manual
will damage the pulsation dampener, and void
factory warranty.
Before doing any maintenance
on the pulsation dampener,
be certain all pressure is
completely vented from the
pump, suction, discharge,
piping, and all other openings and connections.
Be certain the air supply is locked out or made
non-operational, so that it cannot be started while
work is being done on the pump. Be certain that
approved eye protection and protective clothing
are worn all times in the vicinity of the pump.
Failure to follow these recommendations may
result in serious injury or death.
WARNING
Take action to prevent static
sparking. Fire or explosion
can result, especially
when handling ammable
liquids. The pump, piping,
valves, containers or other
miscellaneous equipment
must be grounded. See page 8.
WARNING
POSSIBLE EXPLOSION HAZARD can result if
1, 1, 1, -Trichloroethance, Methylene Chloride
or other Halogenated Hydrocarbon solvents
are used in pressurized uid systems having
Aluminum or Galvanized wetted parts. Death,
serious bodily injury and/or property damage
could result. Consult with the factory if you
have questions concerning Halogenated
Hydrocarbon solvents.
HAZARD WARNING
MODEL SPECIFIC
1: PUMP SPECS

sa ndp ipe rpu mp.c om
6 • Model TA3
ta3mdl2sm-rev0917
Installation And Start-Up
Locate the pump as close to the product being pumped as possible. Keep the suction line length and number of ttings to a minimum. Do not reduce the suction line
diameter.
Air Supply
Connect the pump air inlet to an air supply with sufcient capacity and pressure to achieve desired performance. A pressure regulating valve should be installed to
insure air supply pressure does not exceed recommended limits.
Air Valve Lubrication
The air distribution system is designed to operate WITHOUT lubrication. This is the standard mode of operation. If lubrication is desired, install an air line lubricator
set to deliver one drop of SAE 10 non-detergent oil for every 20 SCFM (9.4 liters/sec.) of air the pump consumes. Consult the Performance Curve to determine air
consumption.
Air Line Moisture
Water in the compressed air supply may cause icing or freezing of the exhaust air, causing the pump to cycle erratically or stop operating. Water in the air supply can
be reduced by using a point-of-use air dryer.
Air Inlet And Priming
To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air ow as desired. If opening the valve
increases cycling rate, but does not increase the rate of ow, cavitation has occurred. The valve should be closed slightly to obtain the most efcient air ow to pump
ow ratio.
Surge Suppressor
Shut-Off Valve
Pressure Gauge
Drain Port
Shut-Off
Valve
Check
Valve
Air Inlet
Discharge
Unregulated Air
Supply to Surge
Suppressor
Pipe Connection
(Style Optional)
Flexible Connector
Flexible Connector
Vacuum
Gauge
Suction
Shut-Off Valve
Drain Port
Air Dryer
Filter Regulator
Muffler
(Optional Piped Exhaust)
Recommended Installation Guide
Available Accessories:
 Surge Suppressor
Filter/Regulator
Air Dryer
1
2
3
Note: Surge Suppressor and
Piping must be supported after
the exible connection
UNIVERSAL ALL AODD, EXCEPT FLAP
2: INSTAL & OP

sa ndp ipe rpu mp.c om Model TA3 • 7
ta3mdl2sm-rev0917
Recommended Installation Guide Troubleshooting Guide
For additional troubleshooting tips contact After Sales Support at [email protected] or 419-524-8388
Symptom: Potential Cause(s): Recommendation(s):
Pump Cycles Once Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Air valve or intermediate gaskets installed incorrectly. Install gaskets with holes properly aligned.
Bent or missing actuator plunger. Remove pilot valve and inspect actuator plungers.
Pump Will Not Operate
/ Cycle
Pump is over lubricated. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.
Lack of air (line size, PSI, CFM). Check the air line size and length, compressor capacity (HP vs. cfm required).
Check air distribution system. Disassemble and inspect main air distribution valve, pilot valve and pilot valve actuators.
Discharge line is blocked or clogged manifolds. Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping.
Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Blocked air exhaust mufer. Remove mufer screen, clean or de-ice, and re-install.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Pump chamber is blocked. Disassemble and inspect wetted chambers. Remove or ush any obstructions.
Pump Cycles and Will
Not Prime or No Flow
Cavitation on suction side. Check suction condition (move pump closer to product).
Check valve obstructed. Valve ball(s) not seating
properly or sticking.
Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged.
Use heavier valve ball material.
Valve ball(s) missing (pushed into chamber or
manifold).
Worn valve ball or valve seat. Worn ngers in valve ball cage (replace part). Check Chemical
Resistance Guide for compatibility.
Valve ball(s) / seat(s) damaged or attacked by product. Check Chemical Resistance Guide for compatibility.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Suction line is blocked. Remove or ush obstruction. Check and clear all suction screens or strainers.
Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Pump Cycles Running
Sluggish / Stalling,
Flow Unsatisfactory
Over lubrication. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation.
Icing. Remove mufer screen, de-ice, and re-install. Install a point of use air drier.
Clogged manifolds. Clean manifolds to allow proper air ow.
Deadhead (system pressure meets or exceeds air
supply pressure).
Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero ow.
(Does not apply to high pressure 2:1 units).
Cavitation on suction side. Check suction (move pump closer to product).
Lack of air (line size, PSI, CFM). Check the air line size, length, compressor capacity.
Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Air supply pressure or volume exceeds system hd. Decrease inlet air (press. and vol.) to the pump. Pump is cavitating the uid by fast cycling.
Undersized suction line. Meet or exceed pump connections.
Restrictive or undersized air line. Install a larger air line and connection.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Suction line is blocked. Remove or ush obstruction. Check and clear all suction screens or strainers.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Check valve obstructed. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs. Purging the chambers of air can be dangerous.
Product Leaking
Through Exhaust
Diaphragm failure, or diaphragm plates loose. Replace diaphragms, check for damage and ensure diaphragm plates are tight.
Diaphragm stretched around center hole or bolt holes. Check for excessive inlet pressure or air pressure. Consult Chemical Resistance Chart for compatibility
with products, cleaners, temperature limitations and lubrication.
Premature Diaphragm
Failure
Cavitation. Enlarge pipe diameter on suction side of pump.
Excessive ooded suction pressure. Move pump closer to product. Raise pump/place pump on top of tank to reduce inlet pressure.
Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener.
Misapplication (chemical/physical incompatibility). Consult Chemical Resistance Chart for compatibility with products, cleaners, temperature limitations
and lubrication.
Incorrect diaphragm plates or plates on backwards,
installed incorrectly or worn.
Check Operating Manual to check for correct part and installation. Ensure outer plates have not been
worn to a sharp edge.
Unbalanced Cycling Excessive suction lift. For lifts exceeding 20’ of liquid, lling the chambers with liquid will prime the pump in most cases.
Undersized suction line. Meet or exceed pump connections.
Pumped uid in air exhaust mufer. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly.
Suction side air leakage or air in product. Visually inspect all suction-side gaskets and pipe connections.
Check valve obstructed. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket.
Check valve and/or seat is worn or needs adjusting. Inspect check valves and seats for wear and proper setting. Replace if necessary.
Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs.
UNIVERSAL ALL SANDPIPER, EXCEPT FLAP
2: INSTAL & OP

sa ndp ipe rpu mp.c om
8 • Model TA3
ta3mdl2sm-rev0917
Composite Repair Parts Drawing
4
26
28
3
15
24.5
24.3
24.2
24.4
24.1
20
23.1
23.2
23.3
23.5
18
1
23.4
2
5
27
2112
25
7
19
16
10
17
8
12
14
13
11
6
10
9
17
16
Torque:
600 In-lbs.
Torque:
600 In-lbs.
MODEL SPECIFIC
3: EXP VIEW

sa ndp ipe rpu mp.c om Model TA3 • 9
ta3mdl2sm-rev0917
Composite Repair Parts List
ITEM
   
1 070.014.170 Bearing, Sleeve 1
2 095.078.156 Body 1
3 165.023.000 Cap 1
4 170.005.330 Capscrew, Hex Hd - 5/16-18 X 7/8 1
5 170.024.330 Capscrew, Hex Hd - 7/16-14 X 1 4
6 170.082.330 Capscrew, Hex Hd, 1/2-13UNC X 2.75 8
7 196.100.015 Chamber, Inner 1
8 196.146.156 Chamber, Outer 1
196.146.010 Chamber, Outer 1
196.146.110 Chamber, Outer 1
   
   
   
   
   
   
   
11 866.078.330 Tube Fitting 1
12 545.008.330 Nut, Hex - 1/2-13 9
13 560.022.360 O-Ring 1
14 612.043.330 Plate, Activator 1
15 612.044.330 Plate, Activator 1
16 612.192.157 Plate, Inner Diaphragm 1
17 612.194.157 Plate, Outer Diaphragm Assy.
(Alum Units Only) 1
612.194.010 Plate, Outer Diaphragm Assy.
(Cast Iron Units Only) 1
612.194.110 Plate, Outer Diaphragm Assy.
(Stainless Units Only) 1
18 675.054.080 Ring, Retainer 1
19 685.066.120 Rod, Diaphragm 1
20 685.048.120 Rod, Activator 1
   
23 893.021.000 Valve Assembly 1
23.1 095.020.162 Body, Valve 1
23.2 560.001.360 O-Ring 1
23.3 622.002.162 Poppet 1
23.4 670.007.162 Spring Retainer 1
23.5 780.013.115 Spring, Compression 1
24 893.023.000 Valve Assembly 1
24.1 095.019.162 Body, Valve 1
24.2 622.002.162 Poppet 1
24.3 780.013.115 Spring, Compression 1
24.4 560.001.360 O-Ring 1
24.5 866.010.162 Elbow, Male 1
25 900.003.330 Washer, Lock - 1/2 8
26 900.004.330 Washer, Lock - 5/16 1
27 900.006.330 Washer, Lock - 7/16 4
28 901.009.115 Washer, Flat - 5/16 1
MODEL SPECIFIC
3: EXP VIEW

sa ndp ipe rpu mp.c om
10 • Model TA3
ta3mdl2sm-rev0917
Material Codes - The Last 3 Digits of Part Number
000.....Assembly, sub-assembly;
and some purchased items
010.....Cast Iron
015.....Ductile Iron
020.....Ferritic Malleable Iron
080.....Carbon Steel, AISI B-1112
110 .....Alloy Type 316 Stainless Steel
111 .....Alloy Type 316 Stainless Steel
(Electro Polished)
112 .....Alloy C
113 .....Alloy Type 316 Stainless Steel
(Hand Polished)
114 .....303 Stainless Steel
115 .....302/304 Stainless Steel
117 .....440-C Stainless Steel (Martensitic)
120.....416 Stainless Steel
(Wrought Martensitic)
148.....Hardcoat Anodized Aluminum
150.....6061-T6 Aluminum
152.....2024-T4 Aluminum (2023-T351)
155.....356-T6 Aluminum
156.....356-T6 Aluminum
157.....Die Cast Aluminum Alloy #380
158.....Aluminum Alloy SR-319
162.....Brass, Yellow, Screw Machine Stock
165.....Cast Bronze, 85-5-5-5
166.....Bronze, SAE 660
170.....Bronze, Bearing Type,
Oil Impregnated
180.....Copper Alloy
305.....Carbon Steel, Black Epoxy Coated
306.....Carbon Steel, Black PTFE Coated
307.....Aluminum, Black Epoxy Coated
308.....Stainless Steel, Black PTFE Coated
309.....Aluminum, Black PTFE Coated
313.....Aluminum, White Epoxy Coated
330.....Zinc Plated Steel
332.....Aluminum, Electroless Nickel Plated
333.....Carbon Steel, Electroless
Nickel Plated
335.....Galvanized Steel
337.....Silver Plated Steel
351.....Food Grade Santoprene®
353.....Geolast; Color: Black
354.....Injection Molded #203-40
Santoprene® Duro 40D +/-5;
Color: RED
356.....Hytrel®
357.....Injection Molded Polyurethane
358.....Urethane Rubber
(Some Applications)
(Compression Mold)
359.....Urethane Rubber
360.....Nitrile Rubber Color coded: RED
363.....FKM (Fluorocarbon)
Color coded: YELLOW
364.....EPDM Rubber
Color coded: BLUE
365.....Neoprene Rubber
Color coded: GREEN
366.....Food Grade Nitrile
368.....Food Grade EPDM
371.....Philthane (Tuftane)
374.....Carboxylated Nitrile
375.....Fluorinated Nitrile
378.....High Density Polypropylene
379.....Conductive Nitrile
408.....Cork and Neoprene
425.....Compressed Fibre
426.....Blue Gard
440.....Vegetable Fibre
500.....Delrin® 500
502.....Conductive Acetal, ESD-800
503.....Conductive Acetal, Glass-Filled
506.....Delrin® 150
520.....Injection Molded PVDF
Natural color
540.....Nylon
542.....Nylon
544.....Nylon Injection Molded
550.....Polyethylene
551.....Glass Filled Polypropylene
552.....Unlled Polypropylene
555.....Polyvinyl Chloride
556.....Black Vinyl
558.....Conductive HDPE
570.....Rulon II®
580.....Ryton®
600.....PTFE (virgin material)
Tetrauorocarbon (TFE)
603.....Blue Gylon®
604.....PTFE
606.....PTFE
607.....Envelon
608.....Conductive PTFE
610.....PTFE Encapsulated Silicon
611 .....PTFE Encapsulated FKM
632.....Neoprene/Hytrel®
633.....FKM/PTFE
634.....EPDM/PTFE
635.....Neoprene/PTFE
637.....PTFE, FKM/PTFE
638.....PTFE, Hytrel®/PTFE
639.....Nitrile/TFE
643.....Santoprene®/EPDM
644.....Santoprene®/PTFE
656.....Santoprene®Diaphragm and
Check Balls/EPDM Seats
661.....EPDM/Santoprene®
666.....FDA Nitrile Diaphragm,
PTFE Overlay, Balls, and Seals
668.....PTFE, FDA Santoprene®/PTFE
• Delrin and Hytrel are registered
tradenames of E.I. DuPont.
• Nylatron is a registered tradename
of Polymer Corp.
• Gylon is a registered tradename
of Garlock, Inc.
• Santoprene is a registered tradename
of Exxon Mobil Corp.
• Rulon II is a registered tradename
of Dixion Industries Corp.
• Ryton is a registered tradename
of Phillips Chemical Co.
• Valox is a registered tradename
of General Electric Co.
UNIVERSAL ALL SP
3: EXP VIEW

Declaration of Conformity
Signature of authorized person Date of issue
Authorised Representative:
IDEX Pump Technologies
R79 Shannon Industrial Estate
Shannon, Co. Clare, Ireland
Attn: Barry McMahon
Revision Level: F
Title
Director of Engineering
October 20, 2005
Date of revision
February 27, 2017
Manufacturer: Warren Rupp, Inc., 800 N. Main Street
Mansfield, Ohio, 44902 USA
Certifies that Air-Operated Double Diaphragm Pump Series: HDB, HDF, M Non-Metallic,
S Non-Metallic, M Metallic, S Metallic, T Series, G Series, U Series, EH and SH High Pressure,
RS Series, W Series, F Series, SMA and SPA Submersibles, and Tranquilizer®Surge Suppressors comply with
the European Community Directive 2006/42/EC on Machinery, according to Annex VIII.
This product has used Harmonized Standard EN809:2012, Pumps and Pump Units
for Liquids - Common Safety Requirements, to verify conformance.
5 - YEAR Limited Product Warranty
Warren Rupp, Inc. (“Warren Rupp”) warrants to the original end-use purchaser that no product sold by Warren Rupp that
bears a Warren Rupp brand shall fail under normal use and service due to a defect in material or workmanship within five
years from the date of shipment from Warren Rupp’s factory. Warren Rupp brands include Warren Rupp®,SANDPIPER®,
SANDPIPER Signature SeriesTM, MARATHON®, Porta-Pump®, SludgeMaster™ and Tranquilizer®.
The use of non-OEM replacement parts will void (or negate) agency certifications, including CE, ATEX, CSA, 3A and
EC1935 compliance (Food Contact Materials). Warren Rupp, Inc. cannot ensure nor warrant non-OEM parts to meet the
stringent requirements of the certifying agencies.
~ See sandpiperpump.com/content/warranty-certifications for complete warranty,
including terms and conditions, limitations and exclusions. ~
UNIVERSAL ALL SP
4: WARRANTY

DATE/APPROVAL/TITLE:
26 SEP 2018 David Roseberry, Director of Engineering
EU Declaration of Conformity
Manufacturer:
Warren Rupp, Inc.
A Unit of IDEX Corporation
800 North Main Street
Mansfield, OH 44902 USA
Warren Rupp, Inc. declares that Air Operated Double Diaphragm Pumps (AODD) and Surge Suppressors
listed below comply with the requirements of Directive 2014/34/EU and all applicable standards.
Applicable Standards
• EN80079-36: 2016 • EN80079-37: 2016 • EN60079-25: 2010
Hazardous Location Applied:
II 2 G Ex h IIC T5...225°C (T2) Gb
II 2 D Ex h IIIC T100°C...T200°C Db
II 2 G Ex h IIB T5...225°C (T2) Gb
II 2 D Ex h IIIB T100°C...T200°C Db
• Metallic pump models with external aluminum components (S Series, HD Series, G Series,
DMF Series, MSA Series, U Series, F Series, T Series)
• Conductive plastic pump models with integral muffler (S Series, PB Series)
• Tranquilizer® surge suppressors
Hazardous Location Applied:
I M1 Ex h I Ma
II 1 G Ex h IIC T5...225°C (T2) Ga
II 1 D Ex h IIIC T100°C...T200°C Da
II 2 G Ex h ia IIC T5 Gb
II 2 D Ex h ia IIIC T100°C Db
II 2 G Ex h mb IIC T5 Gb
II 2 D Ex mb tb IIIC T100° Db
• Metallic pump models with no external aluminum (S series, HD Series, G series)
• Conductive plastic pumps equipped with metal muffler (S series, PB Series)
• ATEX pump models equipped with ATEX rated pulse output kit or solenoid kit
See “ATEX Details” page in user’s manual for more information
See “Safety Information” page for conditions of safe use
Meander 1051
6825 MJ Arnhem
The Netherlands
1. AODD Pumps and Surge Suppressors - Technical File No.: 20310400-1410/MER
2. AODD Pumps - EU Type Examination Certificate No.: DEKRA 18ATEX0094X - DEKRA Certification B.V. (0344)
ATEX
UNIVERSAL ALL SP
4: WARRANTY

Manufacturer: Warren Rupp, Inc., 800 N. Main Street, Mansfield, Ohio, 44902 USA
certifies that SANDPIPER® Air-Operated Double Diaphragm Food Processing Pump Models
and Tranquilizer®Surge Suppressor Models comply with the European Community Regulations:
(EC) No 1935/2004 for Food Contact Materials
(EC) No 2023/2006 Good Manufacturing Practice
(EU) No 10/2011 on plastic materials and articles intended to come in contact with food
Signature of authorized person
Printed name of authorized person
David Roseberry
Date of issue
February 8, 2013
Title
Director of Engineering
Date of revision
February 25, 2019
Declaration of Conformity
T1FB1SASWTS600.
T1FB1S9SWTS600.
T1FB1SDSWTS600.
T1FB1SLSWTS600.
T1FB1S9TWTS600.
T15B1SDSWTS600.
T15B1SSSWTS600.
T15B1SDSSTS600.
T15B1SSSSTS600.
T15B1SSTWTS600.
T30B1SDSWTS600.
T30B1SASSTS600.
T30B1SDSSTS600.
SSB2, TD3SS.
F05B1SGSPTF000.
F05B1SZSPTF000.
F05B1SHSPTF000.
F05B1SDSPTF000.
F10B1SHSNTF600.
F10B1SKSNTF600.
F20B1SKSNTF600.
F20B1SZSNTF600.
F20B1SDDNTF600.
F20B1SHSNTC600.
F20B1SKSNTC600.
F20B1SZSNTC600.
F30B1SHHNTF600.
F30B1SDDNTF600.
F30B1SKSNTF600.
F30B1SZSNTF600.
Food Processing Pump Models:
Tranquilizer®Surge Suppressors:
T15B1SSTSTS600.
T20B1SASWTS600.
T20B1SDSWTS600.
T20B1SASSTS600.
T20B1SDSSTS600.
T20B1SASWTS600.
T20B1SDSWTS600.
T20B1SASSTS600.
T20B1SDSSTS600.
T30B1SASWTS600.
TA1,NG1SS
TA25,NG1SS
TA1-1/2,NG1SS
TA40,NG1SS
F10B1SZSNTF600.
F10B1SDSNTF600.
F15B1SKTNTF600.
F15B1SZSNTF600.
F15B1SHHNTF600.
F15B1SDDNTF600.
F15B1SKSNTC600.
F15B1SZSNTC600.
F15B1SHSNTC600.
F20B1SHHNTF600.
TA2,NG2SS
TA50,NG2SS
TA3,NG2SS
TA80,NG2SS
• This Declaration is based on :
• Declaration of Conformities from raw material suppliers
• Total Migration Analysis per (EU) No 10/2011
• Supporting document will be made available to competent authorities to demonstrate compliance
Plastic Materials: PTFE and FKM/ PTFE coated
The plastic components are suitable to come in contact with multiple food types, provided that storage contact
time does not exceed 1/2 hour, contact temperature does not exceed 40°C and maximum operating
temperatures within the instructions manual are not exceeded. Diaphragm failure may allow process fluids to
come in contact with nonconforming materials. Regular inspections are recommended.
• Materials used in equipment intended for food contact (Annex I (EC) No 1935/2004) :
• Rubber • Metals & Alloys • Plastics
4: WARRANTY