WATANABE G1000 Series User manual

GRAPHIC MULTI-METER
MODEL : G1000 SERIES
SIMPLIFIED INSTRUCTION MANUAL
( STRAIN GAUGE / PROCESS )

Simplified instruction manual MODEL G1000
2/44
■Contents
1. Configurations of model......................................................................................................................3
2. Screen Configurations ........................................................................................................................3
2-1. NAMEAND FUNCTION OF DISPLAY SCREEN.............................................................................................................3
2-2. FUNCTIONAL DESCRIPTION.......................................................................................................................................5
3. Setting..................................................................................................................................................6
3-1. WAVEFORM COMPARISON /WAVEFORM &DISPLACEMENT COMPARISON (EXAMPLE) .........................................6
3-2. SET-VALUE INPUT SCREEN ........................................................................................................................................7
3-3. DATA SETTING LIST ....................................................................................................................................................8
4. Basic Function Setting (Setup) ........................................................................................................13
5. Input Setting.....................................................................................................................................17
5-1. STRAIN GAUGE ........................................................................................................................................................ 17
5-2. ANALOG INPUT SETTING (ACH).............................................................................................................................. 17
5-3. PROCESS INPUT (BCH) ............................................................................................................................................ 21
6. Comparison Set Value (Comparator) (A/Bch) .................................................................................25
7. Hold Function (Hold)........................................................................................................................28
7-1. HOLD FUNCTION SETTING ..................................................................................................................................... 28
8. Waveform Comparison / Waveform & Displacement Comparison (Waveform)............................31
8-1. VARIOUS SETTING AND CORRECTION METHODS .................................................................................................. 31
9. Graphic Display Setting (Graph Disp) ............................................................................................35
10. Linearization...................................................................................................................................38
11. Basic Function Setting 2 (System).................................................................................................39
11-1. PROTECT................................................................................................................................................................. 39
11-2. INITIALIZATION ...................................................................................................................................................... 39
11-3. FUNCTION CHECK ................................................................................................................................................. 39
12. Output .............................................................................................................................................41
12-1. ANALOG OUTPUT SETTING ................................................................................................................................... 41
12-2. BCD OUTPUT SETTING......................................................................................................................................... 41
13. About Error Messages ....................................................................................................................42
14. Accessories.......................................................................................................................................43

Simplified instruction manual MODEL G1000
3/44
1. Configurations of model
The G1000 Series are configured as follows :
Check that there is no discrepancy between the model and its specifications you have chosen when ordering
and the model and its specifications under your hand.
11G
SD memory card function 0 : No function available
1 : Function available
Drive power supply 1 : AC/FREE (100 to 240V AC)
5 : RS-232C
6 : RS-485
3 : BCD parallel + RS-232C
4 : Analog output + RS-232C
Output unit
0 : Strain Gauge + Process input unitInput unit
Series name
* Standard equipment of the comparison output (Photocoupler output) is carried out.
Display model 2 : Japanese, English
* SD memory card is not attached.
(Please purchase the product made from Panasonic separately.)
2 : 24VDC ± 15%
5 0 0 2
2. Screen Configurations
2-1. Name and Function of Display Screen
1) Single Display Screen (Achannel, B channel)
(1)“Display screen
change”key
(2)Pattern used (3)“HOLD”key
(4)“MODE”key
(5)Ach indication
(6)“HOLD PEAK”
operating state
monitor (7)Indicated value
(8)Bar graphic display
(9)“DZ”digital zero key
(10)Comparison
output monitoｒ：
Display of
comparison set value
Unit on display
2) Multi Display Screen (2ch meter)
“HI,LO”comparison output monitor
Ach “DZ”digital
zero key
Ach indication
“HOLD PEAK”
operating state
monitor (Bch) Top Ach indicated value
Bch bar graphic display
Bch “DZ”digital zero key
“HOLD PEAK”
operating state
monitor (Ach)
Bch indication
Bottom Bch indicated value
Unit (kg)
Unit (mm)
Ach bar graphic display

Simplified instruction manual MODEL G1000
4/44
3) Graphic Display Screen
Ach indication
Y-axis indicated value and unit
Y-axis scale unit
(6)“WAIT”
state unit
(11)“Cursor
indication”key
(12)“Cursor movement”key (13)“START/STOP”key
X-axis scale and time (s)
4) Waveform Comparison Display Screen (Ach,Bch)
Y-axis indicated value and unit
Y-axis scale unit
X-axis scale and time (s)
HI limit waveform
set value
LO limit waveform
set value
5) Waveform & Displacement Comparison Display Screen
(14) Y-axis indicated value and unit
Y-axis scale unit
(15)X-axis Indicted
value and unit
X-axis scale and
displacement (unit)
・"MODE" Key
Various settings can be performed with the measurement operation stopped and each output turned off.
When the caution screen for start settings appears and "YES" is selected on it, the main setting screen is
displayed, making it possible to perform setting.
・Comparison output monitors "HH", "HI", "GO", "LO", "LL"
When the comparison output ON/OFF state is displayed on the single screen, a comparison set value is
also displayed. In case of the multi-display screen (2 channel), each ofAch and Bch is independently
displayed. "HH", "HI", "LO", "LL" are used as setting keys. Pressing it displays a 10-key pad on the screen,
allowing data setting. (It can be set during measurement operation)
・Others
I perform control of this product by a screen key and external control. (External control connector)
In external control, control is possible independently by digital zero, hold ofAch and Bch. In addition, as for
the pattern change of setting, a change is possible from external control (P0 to P3) and RS communication.

Simplified instruction manual MODEL G1000
5/44
2-2. Functional Description
The touch panel is used for setting and operation on the screen. If 2 or more points are pressed
simultaneously or quickly pressed continuously, the point so pressed may be detected incorrectly. Be sure
to press only one point at intervals.
It changes according to 1) Meter Setup of ”4. Basic Function Setting (Setup)”.
Display screen of three kinds are available. The state when each of be pressed is
shown according to each meter setting.
◎The display screen changes as follows, when Ach and Bch are selected by meter setting :
Ach (Bch) single screen Ach (Bch)graphic screen
Y-axis = Ach or Bch
X-axis = time (s)
◎Display screen change when 2 channel meter is selected by meter setting
2 channel screen Ach graphic screen
X-axis = time (s)
Bch graphic screen
X-axis = time (s)
◎When Waveform Comparison Ach/Bch or Waveform & Displacement Comparison are selected, no screen
will change
Waveform comparison screen Waveform & Displacement Comparison screen
Y-axis = Ach or Bch Y-axis =Ach
X-axis = time (s) X-axis = Bch

Simplified instruction manual MODEL G1000
6/44
3. Setting
3-1. Waveform Comparison / Waveform & Displacement Comparison (Example)
Ordinary Display Screens Caution Screen for Starting Setting
Main Setting Screen
Note) When no memory-card function,
“SD setup” button is not displayed.
Itemized Setting Screen
Set-value Input Screen
"Each Set" key
HI/LO limit waveform set-value
Comparison range setting
Correction of waveform set valuePreparation of waveform set value
HI/LO limit waveform
set-value clearing Fundamental waveform sampling Waveform movement

Simplified instruction manual MODEL G1000
7/44
3-2. Set-Value Input Screen
1) Measured-value acquisition screen
"CALIBRATION" : Displays
contents to be set with indicator.
Data name to be set
Returns to itemized setting screen.
"SET" key is used to acquire
and finalize measured value.
(Measured value becomes blue
simultaneously with finelizing.)
Display measured value.
*Caution
※When ”4. Basic Function Setting (Setup) 4) Motion Detect”is active, measured value becomes red while
analog output is not stable. Setting is possible even during unstable state.
2) Set-value select screen
Displays the selected value.
"SELECT" is used to select data
to be set with indicator.
Data name to be set
Press key to select set value.
Scrolls set value.
3) 10-key input screen
"INPUT KEY": Used to set
data to be set with indicator.
Data name to be set
Enter set value
with "10-key pad."
Acquire set value and
finalize with "SET" key.
(Set value becomes blue
simultaneously with finalizing.)
"C" is used to change set value to "0".
It can also be used when error occurs.
"+" and "-" are used to set polarity.
"-" may not be accepted according to data setting.

Simplified instruction manual MODEL G1000
8/44
3-3. Data Setting List
Basic Function Setting (Setup)
Setting item
Default value
Setting range
Meter Setup
A channel
Achannel, B channel, 2 channel, Wave Ach, Wave Bch, W&D
Display Cycle
2.5 CPS
12.5, 6.25, 2.5, 1.0, 0.5 CPS
Sampling Cycle
500 CPS
4000, 2000, 1000, 500, 200, 100, 50, 20, 10 CPS
MD Time
0.0
Time 0.0 to 9.9 (second.)
MD Width
1
Comparison width 01 to 99 (digit)
ZT Time
0.0
Correction time 0.0 to 9.9 (second)
ZT Width
0
Correction width 0 to 99 (digit)
Input ON Delay
0.000
0.000 to 4.999 (sec.)
Output Delay
0.000
0.000 to 4.999 (sec.)
Power ON Delay
0
0 to 30 (sec.)
Back Light Time
0
0 to 99 (min)
Contrast
－－－－
0 to 255
Cross Talk
33
0 to 63
Digital ZERO Backup
OFF
OFF, ON
Language
Japanese
Japanese, English
BPS
9600
38400, 19200, 9600, 4800, 2400 BPS
Data Length
7
7, 8
Parity
Even
Even, Odd, None
Stop Bit
2
2, 1
Delimiter
CR+LF
CR+LF, CR, LF
Address (RS-485 ID)
0
00 to 99
Strain Gauge Input Setting
(Ach) (P00 to P15)
Setting item
Default value
Setting range
Pattern Select
－－－－
P00 to 15
Pattern Copy
－－－－
P00 to 15
Sensor Power
2.5V
2.5V, 5V, 10V
ZERO Calibration
0
0.0000
Equivalent Calibration
2.0000
SPIN value (rated-output value) (0.1 to 3.000mV/V)
Actual Load
10000
Span set value (100 to 99999)
Decimal Point
0
0.0000, 0.000, 0.00, 0.0, 0
Digital Shift
0
±99999
Unit
None
Select from among 79 different units.
Moving Average
OFF
OFF, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 (times)
Analog Filter
600
10, 30, 300, 600 (Hz)
Digital Limiter HI
99999
-99998 to 99999
Digital Limiter LO
-99999
-99999 to 99998
Step
1
1, 2, 5, 10

Simplified instruction manual MODEL G1000
9/44
Process Input Setting
(Bch) (P00 to P15)
Setting item
Default value
Setting range
Pattern Select
－－－－
P00 to 15
Pattern Copy
－－－－
P00 to 15
Input Range
±0 to 10V
0 to 10, ±0 to 20mA, 4 to 20mA
Full Scale
10000
0 to 99999
Off set Scale
0
0 to 99999
Full Scale Input
10.000
-10.000 to 10.000, -20.000 to 20.000
Offset Scale input
0
-10.000 to 10.000, -20.000 to 20.000
Decimal Point
0
0.0000, 00.000, 000.00, 0000.0, 0
Digital Shift
0
±99999
Unit
None
Select from among 79 different units.
Moving Average
OFF
OFF, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 (times)
Analog filter
600
10, 30, 300, 600 (Hz)
Digital Limiter HI
99999
-99998 to 99999
Digital Limiter LO
-99999
-99999 to 99998
Step
1
1, 2, 5, 10
Comparison Set Value Setting (Comparator)
(Ach/Bch) (P00 to P15)/(P00 to P15)
Setting item
Default value
Setting range
Pattern Select
－－－
P00 to 15
Pattern Copy
－－－
P00 to 15
HH Limit
1000
-99999 to 99999
HI Limit
500
-99999 to 99999
LO Limit
100
-99999 to 99999
LL Limit
50
-99999 to 99999
HH Hysteresis
1
-9999 to 9999
HI Hysteresis
1
-9999 to 9999
LO Hysteresis
-1
-9999 to 9999
LL Hysteresis
-1
-9999 to 9999
Type
Normal
Normal, Area, Rank
Zero Band
0
0 to 99999
Start Condition
Always
Always, Zero Band, Motion, Z + M

Simplified instruction manual MODEL G1000
10/44
Hold Function (Hold)
(P00 to P15)
Setting item
Default value
Setting range
Pattern Select
－－－
P00 to 15
Pattern Copy
－－－
P00 to 15
Hold
Normal
(1)Normal (2)Sample (3)Peak (4)Valley (5)Peak valley
(6)Area Peak (7)Area Valley (8)Area Peak Valley (9)Time Peak
(10)Time Valley (11)Time Peak Valley (12)Level + Time P
(13)Level + Time V (14)Level +Time P-V
(15)Maximum Value + Level(16)Minimum Value + Level
(17)Inflection Point + Level
*Level = Start level
Start Level
100
±99999
Start Condition
Pass
Pass, Rising Edge, Trailing Edge, More, Less
Detection Time
1000
1 to 9999
Minimum Value
50
1 to 9999
Detection Level
×1/2
×1/4, ×1/2, ×3/4, ×1, ×1.25, ×1.5, ×2, ×3, ×4
Detection Count
1
1 to 9
Inflection Range
30
1 to 99999
Detection Before
20
1 to 999
Detection After
20
1 to 999
Waveform Comparison / Waveform & Displacement Comparison (Waveform)
(P00 to P07)
Setting item
Default value
Setting range
Pattern Select
－－－
P00 to 07
Pattern Write
－－－
P00 to 07
Clear Wave Data
－－－
Sampling
－－－
Sampling Wave Move
－－－
Comparison Wave Draw
－－－
Comparison Wave Edit
－－－
Comparison Area
－－－
Displacement Max Value
10000
0 to 99999
Displacement Min Value
0
0 to 99999