Waterstone GANTRY 3700 User manual

4400 4410-12 4410-18
3700 3710-12 3710-18
Gantry Model #:
3700
3710-12
3710-18
4400
4410-12
4410-18
GANTRY®PULLDOWN FAUCET
INSTALLATION INSTRUCTIONS

1 2 3 4
Turn o water supply. Observe all local
plumbing codes.
Inspect waste and water
supplies for signs of damage.
Replace as necessary.
DO NOT use petroleum
based products on this
faucet.
REQUIRED TOOLS: PARTS INCLUDED:
2. Phillips Screwdriver1. Adjustable Wrench
HK-THC-XX*
TRADITIONAL HANDLE CAP KIT (TRADITIONAL ONLY)
HK-USM1250
UNDER SINK MOUNTING HARDWARE KIT (1-1/4”)
*XX represents nish
BEFORE YOU BEGIN YOUR INSTALLATION:
INSTALLATION GUIDE
LIFETIME WARRANTY
All Waterstone products manufactured by Waterstone carry a Limited
Lifetime Guarantee against functional defect in material or workmanship
in a residential application. Consult with an authorizedWaterstone dealer for
complete information about our warranty.
For any questions or concerns about your faucet’s warranty, contact Waterstone.
Waterstone Faucets
41180 Raintree Court • Murrieta, CA 92562
1-888-304-0660
www.waterstoneco.com

Waterstone faucets are designed for 3 dierent faucet positions. Handle
on left, front and right. Your faucet is congured for the most common
installation (see below).To reverse this and have the handle positioned on
the left, connect the hose for cold water to the hot supply and the hose for
hot water to the cold supply. This will maintain the relationship of pulling
the handle for hot water or pushing for cold water.
HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
AB
C D
A B E
E
G
C D F
F
1. Before connecting supply hoses,
ush supply stops to clear any
debris. Place a bucket underneath
stops and run water for 5 to 10
seconds.Turn water o.
2. Carefully position hot and cold
supplies so they will not interfere
with other hoses.
3. Connect supply hoses (A) to
supply stops (B). DO NOT use teon
tape or plumbers putty. Turn water
back on and check for leaks.
CONNECTING SUPPLY HOSES HANDLE POSITION
A
B
E
D
B
F
C
ACOUNTER
OR SINK
1. 2. 3. 4.
Slide washer (D) and thread the
clamp nut (E) onto threaded
shroud. Tighten nut snug to
underside of sink or counter.
Turn faucet to the desired
handle position. Securely
tighten clamp screws (F).
GANTRY®PULLDOWN FAUCET INSTALLATION
Using scissors, cut plastic tie
on hose protector tube (A) and
remove.
Fit exible hoses (B, C) through
hole on counter or sink. (No
plumbers putty is required.
O-ring will seal base).
RED FOR HOT
BLUE FOR COLD
OPTIONAL HOT COLD INDICATOR RING
(CONTEMPORARY ONLY)
1. To reverse, or remove Hot and Cold Indicator
Ring, unscrew the metal cap, remove ring and ip.
2. Slide ring back onto handle and screw metal
cap back on.
AC
DE
F
B
OPTIONAL DECORATIVE BUTTONS
To change button, nd the slot (A) at bottom of
retainer ring (B).With a small standard screwdriver,
g ently pry retainer ring from faucet handle (C).
Remove button assembly (D). Insert new button
by lining up pin (E) on
handle with hole (F)
on bottom of button
assembly. With slot
facing down, press the
button retainer ring
rmly back into place.

VEN-038-GANT Rev. E
41180 Raintree Court • Murrieta, CA 92562 • 1-888-304-0660 • 951-304-0520 • www.waterstoneco.com
HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
AB
C D
A B E
E
G
C D F
F
HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
H C
AB
C D
A B E
E
G
C D F
F
1. Unscrew and remove the metal cap (A). Remove Hot and Cold Indicator Ring (B).
2. Unscrew and remove holding screw (C) and washer (D).
3. Hold handle (E) in a vertical position. Pull straight o faucet. Rotate handle
away from backsplash then slide handle back onto valve stem (F).
4. Insert holding screw with washer and tighten. Slide Hot and Cold Indicator
Ring onto handle and thread metal cap back into place.
5. To adjust handle tension, turn ring (G) clockwise to increase or
counterclockwise to decrease handle tension.
1. Place a small standard screwdriver in the slot at the bottom of metal ring that surrounds the
handle caps (A). Gently pry the cap from faucet handle (B).
2. Unscrew and remove holding screw (C) and washer (D).
3. Hold the handle (B) in a vertical position. Pull straight o faucet. Rotate handle away from
backsplash then slide handle back onto valve stem (E).
4. Insert holding screw with washer and tighten. Snap handle cap back into place.
5. To adjust handle tension, turn ring (F) clockwise to increase or counterclockwise to decrease
handle tension.
HOW TO ADJUST HANDLE POSITION AND HANDLE TENSION
CONTEMPORARY
TRADITIONAL
1. Gently unscrew and remove spout tip (A) by hand.
2. Remove O-ring (B).To remove aerator (C), push with nger from bottom.
3. Thoroughly rinse aerator with water until all debris is removed.
4. Place aerator, then O-ring back into spout tip.
5. Gently screw spout tip, by hand, snuggly back onto spout.
Depending on quality of your household water, the aerator
and debris screen may become clogged.We recommend
cleaning one week after installation, then a minimum of
once of year thereafter. To remove the debris, follow the
steps below.
CLEANING AERATOR AND DEBRIS SCREEN
B
C
A
1. 2. 3. 4. 5.
B
C
A
1. 2. 3. 4. 5.
On some kitchen countertops, the handle
may hit the backsplash when the faucet
handle is positioned to the left or right
(Fig. 1). Waterstone gives you the option of
adjusting the handle 45 degrees to avoid
hitting backsplash.
FIG.1