Waterstone Hampton Series User manual

41180 Raintree Court
Murrieta, CA 92562
1-888-304-0660
www.waterstoneco.com
MADE IN THE USA
INSTALLATION INSTRUCTIONS
ITEM NO:
4900
Hampton Series Bar or Prep Faucets
BEFORE YOU BEGIN YOUR INSTALLATION:
1. Make sure your water supply is turned o
2. Observe all local plumbing codes
3. Inspect waste and water supplies for any signs of damage and replace as necessary.
4. Do not use petroleum based products on this faucet.
5. Recommended installation hole size: 1 3/8”
RECOMMENDED TOOLS AND MATERIALS
1. Phillips Screwdriver
2. Adjustable Wrench
FAUCET INSTALLATION (see diagram)
1. Remove the clamp nut (A) and washer (B) from the threaded shroud (C) under the faucet and t the faucet exible
hoses and rigid sidespray tube through the hole on the counter or sink. (No plumbers putty is required in that the
faucet has an O-ring seal built into its base).
2. Slide the washer and thread the clamp nut onto the threaded shroud. Make sure clamp screws are screwed back and
thread the nut snug to the underside of the sink or counter.
3. Make sure the faucet is in the correct position you want it for your sink and securely tighten the clamp screws.
CONNECTING SUPPLY HOSES
1. Carefully position the hot and cold supplies so they will not interfere with other hoses
2. Connect the supply hoses to the supply stops
Note - The most common faucet installation is with the handle positioned to the right. Pull the handle for hot water or
push the handle for cold water. If the handle is centered, press it to the right for cold and to the left for hot water
If the handle is installed to the left, reverse the supply hoses (connect the hose for cold water to the hot supply and the
hose for hot water to the cold supply).This will maintain the relationship of pulling the handle for hot water or pushing
for cold water.

ITEM NO:
26790 Madison Ave.
Murrieta, CA 92562
888-304-0660
www.waterstoneco.com
Codes/Standards Applicable
Specified model meets or exceeds the following:
 ASME A112.18.1
 CSA B125.1
 NSF 61
4900
STYLE: HAMPTON
JOB NO:
CUSTOMER NAME:
DIMENSIONS MAY VARY AND ARE SUBJECT TO CHANGE. NO RESPONSIBILITY IS ASSUMED FOR USE OF SUPERCEDED OR VOIDED DATA.
Made in the U.S.A.
DATE: 1-11-08
FAUCETS
Technical Specifications:
 Solid brass construction.
 Ceramic disk valve cartridge.
 3 handle caps included. Plain, and ceramic right hand or
left hand operation indicated for hot and cold.
 2.2 gpm maximum flow rate.
 Lever handle.
 Diverter equipped for connection to optional side spray.
 Easy access side spray diverter
 Reinforced braided connection hoses.
 Adjustable Teflon® “Friction Assist” aids handle
feel and prevents sag.
SUPPLY HOSES- 20” LONG
WITH 3/8" COMPRESSION
FITTINGS
2-3/8" MAX
1 1/4”
2 1/4”
2 1/8”
SIDE SPRAY CONNECTION
WITH 1/4" NPT PIPE FITTING
2 7/8”
6 3/8”
3 1/4”
(162mm)
(73mm)
(57mm)
(54mm)
(32mm)
(83mm)
(60mm)
6 3/4”
13 3/4”
9 1/2”
(349mm)
(241mm)
(171mm)
ITEM NO:
4900
STYLE: HAMPTON
JOB NO:
INTENDED USE:PREP FAUCET
RECOMMENDED HOLE SIZE 1-3/8”
41180 Raintree Court
Murrieta, CA 92562
1-888-304-0660
www.waterstoneco.com
MADE IN THE USA
INSTALLATION INSTRUCTIONS
ITEM NO:
4900
Hampton Series Bar or Prep Faucets
CONNECTING OPTIONAL SIDE SPRAY
1. Mount side spray base in the side spray hole on your sink or counter.
2. Tighten guide nut.
3. Fit sidespray hose through the side spray guide.
4. Remove the sidespray hose cap on the end of the sidespray hose tube on the faucet.
5. Connect and tighten the end of the sidespray hose to the sidespray hose tube underneath the faucet.