WAVE LIGHTING STONE Series User manual

STONE SERIES INSTALLATION GUIDE
MODEL: S21S
STONE SERIES INSTALLATION GUIDE
MODEL: S21S
If for some reason you are missing parts of have a problem with your fixture
DO NOT CALL OR RETURN TO THE RETAILER. Call for direct assistance at 1-877-870-9283.
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING FIXTURES.
If for some reason you are missing parts of have a problem with your fixture
DO NOT CALL OR RETURN TO THE RETAILER. Call for direct assistance at 1-877-870-9283.
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING FIXTURES.
BEFORE INSTALLATION
1. Please check to see that your fixture was not damaged during shipment, and that you received all the hardware needed for
installation. While we strive for perfection, accidents do happen. If you have a problem or are missing any parts, please call
us at 1-877-870-9283 immediately.
2. CAUTION: Disconnect main power at the breaker box before beginning installation. Do not turn power off at the wall
switch only. Failure to properly disconnect the main power supply may result in serious injury.
3. CAUTION: Install the appropriate size lamp in your Stone fixture. Do not exceed the manufacturer’s maximum wattage
restrictions.
4. SPECIAL NOTE: For easier installation, it is recommended the two (2) people be used when making the electrical connections
and mounting the fixture.
BEFORE INSTALLATION
1. Please check to see that your fixture was not damaged during shipment, and that you received all the hardware needed for
installation. While we strive for perfection, accidents do happen. If you have a problem or are missing any parts, please call
us at 1-877-870-9283 immediately.
2. CAUTION: Disconnect main power at the breaker box before beginning installation. Do not turn power off at the wall
switch only. Failure to properly disconnect the main power supply may result in serious injury.
3. CAUTION: Install the appropriate size lamp in your Stone fixture. Do not exceed the manufacturer’s maximum wattage
restrictions.
4. SPECIAL NOTE: For easier installation, it is recommended the two (2) people be used when making the electrical connections
and mounting the fixture.
INSTALLATION INSTALLATION
HARDWARE HARDWARE
1102454-GUES 1102454-GUES
Disconnect main power supply at the breaker box.
DO NOT turn power off at the wall switch only.
CAUTION: FAILURE TO DISCONNECT MAIN
ELECTRICAL POWER MAY RESULT IN SERIOUS
INJURY.
Disconnect main power supply at the breaker box.
DO NOT turn power off at the wall switch only.
CAUTION: FAILURE TO DISCONNECT MAIN
ELECTRICAL POWER MAY RESULT IN SERIOUS
INJURY.
Install integrated lamp/ballast
(SBCFL). Use SBCFL specified on
fixture. Grasp the plastic base,
insert pins into socket and rotate
clockwise until secure.
Install integrated lamp/ballast
(SBCFL). Use SBCFL specified on
fixture. Grasp the plastic base,
insert pins into socket and rotate
clockwise until secure.
TURN ON MAIN POWER. TURN ON MAIN POWER.
1 12 23 3
8 89 9
10 10
4 4
5 5
6 6
7 7
BLACKBLACK
WHITEWHITE
GROUND WIRE
GREEN OR BARE
GROUND WIRE
GREEN OR BARE
WIRE NUT OR OTHER
ACCEPTABLE CONNECTOR
120 VOLT POWER SUPPLY
ALWAYS CONNECT BLACK TO BLACK,
WHITE TO WHITE, AND BARE OR
GREEN GROUNDING CONNECTORS
LIGHT FIXTURE
BLACKBLACK
WHITEWHITE
GROUND WIRE
GREEN OR BARE
GROUND WIRE
GREEN OR BARE
WIRE NUT OR OTHER
ACCEPTABLE CONNECTOR
120 VOLT POWER SUPPLY
ALWAYS CONNECT BLACK TO BLACK,
WHITE TO WHITE, AND BARE OR
GREEN GROUNDING CONNECTORS
LIGHT FIXTURE
Customer Service 1-877-870-9283
www.wavelighting.com
Customer Service 1-877-870-9283
www.wavelighting.com

BALLAST AND LAMP REPLACEMENT INSTRUCTIONS
Product contains an integrated Lamp/Ballast combination. To remove, grasp plastic area on each side of
bulb area and rotate counterclockwise. Replace with MAX 26W SBCFL(GU-24) that is marked with the
UL and C, US Logo. Use SBCFL marked - Not for use where directly exposed to water. Do not use SBCFL
marked - Not for use in totally enclosed luminaire.
Mark means lamp contains Mercury.
Follow disposal laws.
See www.lamprecycle.org
Hg
BALLAST AND LAMP REPLACEMENT INSTRUCTIONS
Product contains an integrated Lamp/Ballast combination. To remove, grasp plastic area on each side of
bulb area and rotate counterclockwise. Replace with MAX 26W SBCFL(GU-24) that is marked with the
UL and C, US Logo. Use SBCFL marked - Not for use where directly exposed to water. Do not use SBCFL
marked - Not for use in totally enclosed luminaire.
Mark means lamp contains Mercury.
Follow disposal laws.
See www.lamprecycle.org
Hg
HOOD
BASE
This fixture may have an integral photo sensor that turns the fixture off during the day and on at night. The photo sensor is not
adjustable. The fixture could possibly cycle on and off due to light reflected from nearby surfaces into the photo sensor. If cycling
occurs, remove the photo sensor nut and install the swivel hood and base.
The hood and base are adjustable. The hood can be rotated and the base can be cut along the dotted line to reduce overall length. Check operation
before cutting the base.
HOOD
BASE
This fixture may have an integral photo sensor that turns the fixture off during the day and on at night. The photo sensor is not
adjustable. The fixture could possibly cycle on and off due to light reflected from nearby surfaces into the photo sensor. If cycling
occurs, remove the photo sensor nut and install the swivel hood and base.
The hood and base are adjustable. The hood can be rotated and the base can be cut along the dotted line to reduce overall length. Check operation
before cutting the base.