Waypoint LV Instruction Manual

WAYPOINT®LV POST CAP LIGHTING
GUIDELINES AND INSTALLATION INSTRUCTIONS
Please consult your local codes before installing low voltage products.
BEFORE YOU START!
The Junction Box is used as a power source for up to six
separate light sources and will typically be placed in each
post. All lighting in the Waypoint system easily plugs
into the Junction Box. See gure 1, letter A. Wire runs
from the transformer to a Junction Box and then between
Junction Boxes throughout your project. No longer is
there a need to string one wire through the entire railing,
simply cut wire in lengths of each section and attach to the
Junction Box located in every post. See gure 1, letter B.
HOW TO:
USE THE JUNCTION BOX
gure 1.
Remove cover and attach low voltage wire to the Junction Box.
After stringing your wire and connecting it to the
Junction Box simply plug the post cap lead into one of the
six ports of the Junction box. See gure 2. Once entire
job is complete and all lighting is working, use a small
amount of Waymark PVC glue on opposite corners of the
base to secure light to post.
HOW TO:
INSTALL WAYPOINT POST CAPS
Waypoint LV Lights are a product of Waymark Products LLC. - www.waymarkproducts.com - Waypoint is an registered trademark of Waymark Products, LLC. 2014-149
A
A
B
gure 2.
Illustration Content:
1: Low Voltage Post Cap
2: Junction Box
3: Low Voltage Post Sconce
4: Low Voltage Strip Light
5: Low Voltage Star Bright Light
6: Low Voltage Wiring
7: Transformer
1
6
5
4
3
2
7

Waypoint LV Lights are a product of Waymark Products LLC. - www.waymarkproducts.com - Waypoint is an registered trademark of Waymark Products, LLC. 2014-149
STEP 2:
Mark hole for wire. Make sure to drill hole large enough (5/16” or more)
for the plug to pass through easily.
STEP 1:
HOW TO: INSTALL POST SCONCE
Select mounting location for light, be certain you have enough
room to run wires before drilling hole.
STEP 3:
Remove Sconce cover by twisting. Attach sconce to post using screws (included). Note: Vertical line on light
is used for centering and to keep light level when installing. Pre-drilling holes will make installation quicker.
See gure 3 for illustration on how to line up correctly.
STEP 4:
Twist cover on light in opposite direction.
gure 3.
WAYPOINT®LV POST SCONCE LIGHTING
GUIDELINES AND INSTALLATION INSTRUCTIONS
Please consult your local codes before installing low voltage products.
BEFORE YOU START!
The Junction Box is used as a power source for up to six
separate light sources and will typically be placed in each
post. All lighting in the Waypoint system easily plugs into
the Junction Box. See gure 1, letter A. Wire runs from the
transformer to a Junction Box and then between Junction
Boxes throughout your project. No longer is there a need
to string one wire through the entire railing, simply cut wire
in lengths of each section and attach to the Junction Box
located in every post. See gure 1, letter B.
HOW TO:
USE THE JUNCTION BOX
gure 1.
Remove cover and attach low voltage wire to the Junction Box.
A
A
B
Illustration Content:
1: Low Voltage Post Cap
2: Junction Box
3: Low Voltage Post Sconce
4: Low Voltage Strip Light
5: Low Voltage Star Bright Light
6: Low Voltage Wiring
7: Transformer
1
6
5
4
3
2
7

WAYPOINT®LOW VOLTAGE STRIP LIGHT
GUIDELINES AND INSTALLATION INSTRUCTIONS
Please consult your local codes before installing low voltage products.
BEFORE YOU START!
The Junction Box is used as a power source for up to six
separate light sources and will typically be placed in each
post. All lighting in the Waypoint system easily plugs into
the Junction Box. See gure 1, letter A. Wire runs from the
transformer to a Junction Box and then between Junction
Boxes throughout your project. No longer is there a need
to string one wire through the entire railing, simply cut wire
in lengths of each section and attach to the Junction Box
located in every post. See gure 1, letter B.
HOW TO:
USE THE JUNCTION BOX
gure 1.
Remove cover and attach low voltage wire to the Junction Box.
A
A
B
Illustration Content:
1: Low Voltage Post Cap
2: Junction Box
3: Low Voltage Post Sconce
4: Low Voltage Strip Light
5: Low Voltage Star Bright Light
6: Low Voltage Wiring
7: Transformer
1
6
5
4
3
2
7
Waypoint LV Lights are a product of Waymark Products LLC. - www.waymarkproducts.com - Waypoint is an registered trademark of Waymark Products, LLC. 2014-149
STEP 2:
Insert wire into hole and pull excess wire through.
STEP 1:
HOW TO: INSTALL THE STRIP LIGHT
Select location for light, mark and drill hole large enough (5/16” or
more) for connector to pass easily. Note: Wire for light is located on
one end of the strip; install that end closest to your power source.
STEP 3:
Install each bracket with included screws, center holes in bracket should be approx. 18” apart. Note: To install
straight, be sure center hole in each bracket is the same distance from the edge. See gure 2.
STEP 4:
Snap Strip Light into each bracket see gure 3 (brackets pivot on center screw to line up with lights).
gure 2.
STEP 5:
Plug wire into Junction Box (use extension cord LV3EXT for additional length if needed).
gure 3.

STEP 2:
Remove the grommet from the light; insert the
female end into the hole followed by the male end.
STEP 1:
HOW TO: INSTALL THE STAR BRIGHT LIGHT
Select location for light, mark and drill an 11/32”
hole.
STEP 3:
Place the grommet over both ends of the wire and
slide tight over the barrel of the Star Bright,
squeezing it tight and ush to the wall of the
PVC/Composite Rail.
STEP 4 (FOR BOTH WALL THICKNESS SIZES):
If connecting in a daisy chain, one wire will connect to the power
source (male end) while the other wire (female end) will connect to the
next Star Bright wire and so on (male to female).
WAYPOINT®LV STAR BRIGHT LIGHTING
GUIDELINES AND INSTALLATION INSTRUCTIONS
Illustration Content:
1: Low Voltage Post Cap
2: Junction Box
3: Low Voltage Post Sconce
4: Low Voltage Strip Light
5: Low Voltage Star Bright Light
6: Low Voltage Wiring
7: Transformer
1
6
5
4
3
2
7
Waypoint LV Lights are a product of Waymark Products LLC. - www.waymarkproducts.com - Waypoint is an registered trademark of Waymark Products, LLC. 2014-149
FOR PVC/COMPOSITE MATERIAL: FOR PVC/METAL MATERIAL:
Wall thickness over .100, Grommet used to hold
barrel to rail from the inside. See gure 1.
Wall thickness under .100, Grommet is to be
installed in the rail hole. See gure 2.
STEP 5 (FOR BOTH WALL THICKNESS SIZES):
Female end of wire on last light doesn’t need to connect to anything.
STEP 2:
Slip the grommet off the barrel but leave over the
wires, slide grommet to the end near plugs.
STEP 1:
Select location for light, mark and drill an 7/16” hole.
STEP 3:
Insert female end into hole, then male end and pull
wire through hole and rmly seat the grommet.
STEP 3A:
Push the barrel of the Star Bright into the grommet
and seat snug against the rail.
gure 1. gure 2.