Weil-McLain Eco Tec 2 Series User manual

Part Number 550-143-015/1221
Read the boiler rating label
to determine the size and
series number.
Series 2
80/110/150/199
Wall Mount Gas-Fired
Condensing Boilers – Combi and Heating Only Models
Multi-Boiler Wiring Kit Instructions
(RS-485 Communication)
Recommended tools
Phillips screwdriver
Flat blade screwdriver
Paper/pen
Boiler manual
P/N 383-700-272 Kit Contents:
Description Part No. Qty
Wiring Harness, RS-485 Communication 591392107 1
Vinyl Grommet 562248771 1
1/2" Sheet Metal Screw 562138550 2
1 1/2" Sheet Metal Screw 562137536 4
Communication Board 511330460 1
Junction Box Top 469040072 1
Junction Box Bottom 469040071 1
Plastic Anchor 563210627 4
STOP!
Read before proceeding
Hazard denitions
The following defined terms are used throughout
this instruction to bring attention to the presence
of hazards of various risk levels or to important
information concerning the life of the product.
Indicates presence of hazards that will
cause severe personal injury, death or
substantial property damage.
Indicates presence of hazards that can
cause severe personal injury, death or
substantial property damage.
Indicates presence of hazards that will
or can cause minor personal injury or
property damage.
Indicates special instructions on
installation, operation or maintenance
that are important but not related to
personal injury or property damage.
These instructions must only be
used by a qualied installer/service
technician. Read all Instructions com-
pletely before beginning the installation.
Failure to follow all instructions can cause
severe personal injury, death or substantial
property damage.
Improper installation, adjustment,
alteration, service or maintenance can
cause property damage, personal injury
(exposure to hazardous materials) or
loss of life. Refer to the user’s informa-
tion manual provided with this boiler or
available on-line at Weil-McLain.com.
Installation and service must be per-
formed by a qualied installer, service
agency or the gas supplier (who must
read and follow the supplied instruc-
tions before installing, servicing, or re-
moving this boiler. is boiler contains
ceramic ber and berglass materials
that have been identied as carcinogen-
ic, or possibly carcinogenic, to humans).

Part number 550-143-015/1221
2
Multi-Boiler Wiring Kit Instructions
Figure 1 Removing Control Panel Cover
4. Remove two (2) Phillips head screws that hold control
tray cover plate in place. Lift and pull cover away from
tray. Set control tray cover to side.
Label wires before removing
Label all wires prior to disconnection when
servicing controls. Wiring errors can cause
improper and dangerous operation.
Mounting the Junction Box
1. Measure and mark the mounting location, using the
harness length as a reference. Ensure some slack to
avoid stressing the wiring.
2. Install the junction box to a nearby surface using the
four supplied screws through the holes in the junction
box sides.
3. For drywall installations, use the included drywall an-
chors for mounting the junction box.
Before proceeding:
1. Shut down the power to the boiler.
Shut off power to the boiler. Failure to do so
can result in severe personal injury, death or
substantial property damage.
2. Remove door by disengaging the two (2) latches at the
sides of the front door.
3. Slightly lift and pull the door away from the boiler to
remove.
Installing Harness
1. Route the 5-pin side of the supplied harness through the
low voltage knockout on the bottom of the boiler cabinet,
indicated as “A” in Figure 3 on page 3.
2. The harness should route behind the control mounting
bracket, indicated as “B” in Figure 3 on page 3.
3. Route the harness through the large opening on the top
right of the control mounting bracket (“C” in Figure 3 on
page 3). Make connection to boiler control board “D”
in Figure 3 on page 3.
4. Press the mounting clip through the hole in the right side
of the control mounting bracket at approximate location
indicated by “B” in Figure 3 on page 3.
5. Firmly insert the grommet, supplied on the harness, into
the knockout in the bottom of the boiler cabinet.
6. Connect the Ethernet side of the harness into the circuit
board in the junction box. Firmly install the grommet.
Figure 2 Junction Box
Remove these two (2) screws

Part number 550-143-015/1221 3
Multi-Boiler Wiring Kit Instructions
Figure 3 5-pin Wire Routing

4
Weil-McLain
500 Blaine Street
Michigan City, IN 4360-2388
weil-mclain.com
Part Number 550-143-015/1221
Multi-Boiler Wiring Kit Instructions
Connector J12
1. Wiring for RS485 communication harness endpoint circuit
board is as follows:
a. JP4-1 = A2 (RS485 Multi-boiler Bus A+)
b. JP4-2 = B2 (RS485 Multi-boiler Bus B-)
c. JP4-3 = GND (RS485 Multi-boiler Bus GND)
d. JP4-4 = A3 (RS485 Multi-boiler Bus A+)
e. JP4-5 = B3 (RS485 Multi-boiler Bus B-)
f. JP4-6 = GND (RS485 Multi-boiler Bus GND)
g. JP4-7 = GND (BMS Ground)
h. JP4-8 = BMS B (BMS B-)
i. JP4-9 = BMS A (BMS A+)
2. Boiler to boiler wiring connections (see wiring at right)
a. Use shielded 3-wire cable. Do not exceed 1,000 feet
length.
b. Connect 3-wire cable between Boiler-to-Boiler OUT
(JP4-GND, B2, A2) on one boiler to Boiler-to-Boiler
IN (JP4-GND, B3, A3) on the next boiler.
c. Continue this wiring until all boilers are interconnected.
DO NOT return last shadow’s wires to
Master’s A3/B3/GND ports! is will create a communi-
cation loop, which will cause duplication of information
and clashes in communication. e result is undesired and
unknown behavior, up to and including complete loss of
communication.
3. For applications using only BMS, use the wiring har-
ness supplied with the boiler (and also sold separately,
P/N 383-700-401). Remove pre-cut insulation on the har-
ness and use wire nuts to tie in eld wiring. BMS harness
leads are as follows:
a. J12-1 = BMS A+
b. J12-2 = BMS B-
c. J12-5 = BMS Ground
4. MODBUS to BMS
a. The control is equipped with MODBUS communication
to communicate with a BMS.
b. Use terminal JP4 (JP4-BMS A+, BMS B-, GND) to
wire to the BMS control.
c. If the BMS uses BACnet protocol, install a BACnet
converter between the BMS and the ECO Tec MOD-
BUS-to-BMS terminals on JP4.
5. Navigate to the Modbus Setting screen on the display.
This is accessed via the contractor menu by pressing and
holding the WM Logo from the home screen.
6. Adjust all necessary Modbus settings to match the BMS
system being utilized.
7. Install the junction boxfront panel using the supplied
screws.
Reinstall control bracket front panel and boiler
door after start-up or servicing. The door must
be securely fastened to the boiler to prevent the
boiler from drawing air from inside the boiler
room.
Wiring BMS/Multi-Boiler