Weil-McLain Ultra Electric Water Heater User manual

This document must only be used by a qualified heating installer/service
technician. Read all instructions, including these instructions and the Boiler
Manual, before installing. Perform steps in the order given. Failure to comply
could result in severe personal injury, death or substantial property damage.
Part No. 550-101-220/1002
Gas-fired
with
water boiler
Wall mounting
(Instructions for wall
mounting Ultra
boilers — for use
only with Weil-Mclain
wall-mounting kit,
P/N 389-900-180)

Part number 550-101-220/1002
2
GAS-FIRED WATER BOILER — Wall Mounting Instructions
Remove jacket front panel
1. Follow Boiler Manual instructions on pages 1
through 9, including removal of the boiler jacket
front panel. This will simplify lifting and handling
the boiler when mounting.
Prepare boiler for wall mounting
1. If the piping will be routed out the top of the boiler,
no special preparation is needed other than that
given in the Boiler Manual.
2. To route the piping through the bottom of the
boiler enclosure:
a. Remove knockouts from bottom piping penetrations
as shown in Figure 1.
b. Insert grommets into the penetration holes as shown.
Figure 1 Install bottom-piping grommets
Install wall-mount bracket
1. Locate studs.
2. Place the wall-mount bracket on the wall, using a
level to align correctly.
3. Place the bracket so the mounting slots are centered
over the studs.
4. Level the bracket and trace the outline of the screw
slots with a pencil.
5. Remove bracket and drill holes 1/4" diameter by
3 inches deep, centered on the screw slot outlines.
(For metal stud walls, using 3/16" toggle bolts, drill
required clearance holes.)
6. See Figure 2. Position bracket on wall. Insert and
loosely tighten the two lag screws (or toggle bolts
for metal studs).
7. Level the bracket. Then tighten screws securely. For
drywall or plaster lathe installations, avoid
tightening so much that brackets dig into wall
surface.
STOP! Read before proceeding
The wall must be vertically plumb and
capable of carrying the weight of the
boiler. The operating weights are:
• 181 pounds for the Ultra-155
• 192 pounds for the Ultra-230.
1Stud spacing: Bracket holes are spaced for
studs on 16-inch centers. For other stud
spacing, provide secure, solid mounting
surface on which to attach the boiler wall-
mounting bracket.
2Wood stud wall: Install bracket with lag
screws (3/8" x 3") included in kit, only
into the studs.
3Metal stud wall: Secure bracket to studs
with 3/16-inch toggle bolts and 3/16-inch
flat washers (not included with kit).
4DO NOT attempt to attach the wall
mount bracket using anchors or any
means other than directly securing to the
wall studs (or equivalent wood structure
if studs are not on 16-inch centers).
5The boiler bracket must engage with the
wall-mount bracket. Make sure the
brackets are not just resting edge to edge.
6Mount the boiler on the wall following
these instructions. Perform all procedures
given in the Boiler Manual on pages 1
through 9 before mounting the boiler.
7The boiler is heavy. Use caution not to
drop the boiler or cause bodily injury
while lifting and handling.Verify that the
boiler is securely attached to prevent
possibility of boiler falling after
installation.
Failure to comply with above could
result in severe personal injury, death or
substantial property damage.
Verify kit contents
1. Wall-mount bracket.
2. Black iron bushing, 1" x 1/8" NPT.
3. Lag screws, (2) 3/8" x 3" hex head.
4. Grommet, (1) 7/8" O.D.
5. Grommets, (2) 1 3/8" O.D.
6. Automatic air vent, 1/8" NPT.
7. Items 2 through 6 are needed only if routing piping
through bottom of enclosure.
8. Verify all parts listed above are available before
proceeding.

Part number 550-101-220/1002 3
GAS-FIRED WATER BOILER — Wall Mounting Instructions
Figure 2 Install wall-mount bracket
Place boiler on bracket
1. Measure 30 inches below the bottom edge of the
wall-mount bracket. Strike a line or place a piece of
masking tape on the wall with its top edge even
with the 30-inch mark. (This line, or tape, will
indicate whether the boiler has been properly seated
onto the wall-mount bracket.)
2. Obtain assistance to lift the boiler into position:
a. See Figure 3.
b. Lift the boiler high enough that its rear bracket will be
above the wall-mount bracket.
c. Let the rear of the boiler slide against the lag screw
heads as you lower the boiler into place.
d. When the brackets are engaged correctly, the bottom
of the boiler enclosure will be at or near the pencil line,
or tape, you applied in step 1.
e. If the boiler does not slide down close to the mark, or
tape , adjust until the brackets properly engage.
Figure 3 Place boiler on wall-mount bracket
Piping with top penetrations
1. Follow all instructions in the Boiler Manual.
Piping with bottom penetrations
Use two wrenches when tightening
piping at boiler, using one wrench to
prevent the boiler pipe from turning.
Failure to support the boiler piping
connections to prevent them from
turning could cause damage to boiler
components.
1. To route piping through bottom of enclosure:
a. See Figure 4.
b. Remove pipe caps from bottoms of supply, return and
gas lines to route piping through bottom.
c. Install 1" pipe cap on top of return pipe (Figure 4,
item 7).
d. Install ½" pipe cap on top of gas line (Figure 4, item 8).
e. Install 1" x 1" x ¾" tee (Figure 4, item 4), ¾" steel elbow
(item 5), relief valve (item 6), 1" x 1/8" bushing (item 9)
and air vent (item 10) on top of the supply pipe as
shown.
f. Refer to the Boiler Manual for completion of all piping.
Connect piping to: 1" NPT male boiler return (Figure 4,
item 1), 1" NPT male boiler outlet (item 3) and ½"
NPT male gas (item 2). Apply pipe dope sparingly.
Use pipe dope listed for use with propane gas for the
gas line connections. Refer to Boiler Manual for details.
g. Follow all Boiler Manual instructions for piping the
boiler.
Figure 4 Bottom-piping configuration only

Part number 550-101-220/1002
4
GAS-FIRED WATER BOILER — Wall Mounting Instructions