Westinghouse WFB2804AB User manual

WFB2804AB WFB2804WB

z

100 100
50~75 mm
100

The side in which the door opens can be
changed from the left side (as supplied)
to the right side, if the installation site
allows for it. Tools you will need:
Note: Before you start lay the freezer on
it’s back in order to gain access to the
base, you should rest it on soft foam
packaging or similar material to avoid
damaging the backboard of the freezer. To
reverse the door. The following steps are
generally recommended.
1．Stand the freezer upright.
Remove the screw hole cover and upper
hinge cover（left）as follow diagram.
2. Remove the three screws as follow
diagram. Lift the left upper hinge part.
3.Lift the door and place it on a padded
surface to prevent scratching.
4. Loose screw ③，remove part ①and
part ②，then install them to the right side
and tighten securely.
①Door stopper
②Limit block
③Self-tapping screw

5. Place freezer flatwise，remove part ①
and part ②.Loose screw ④and then
remove part ③.
①Screw cover
②Adjustable bottom feet part
③Right lower hinge part
④Special flange self-tapping
screw
6. Just remount to the step 6, change
part ①and part ②to left and part ③
to right and then fix part ③with screws④.
Note: 1. You need move hinge axis from
hole ①to ②,move adjustable bottom
feet part from hole ③to ④before
transfer.
7. Set the door into its new place making
sure the pin enters the bushing at the
lower frame section.
8. Replace the lid by fitting the upper
hinge core into the upper door's hole,
securing it with the 3 screws.
9. Put the screw hole cover and upper
hinge cover（right ）as follow diagram.
10.Switch the handles from the right to the
left（only for the model with handles）.

①Handle cover
②Screw
③Handle part
④Cover-screw cap
Note！
Due to unceasing modification of our
products, handle may be slightly different
from this instruction manual, but its
functions and using methods remain the
same. Switch the handles from the right to
the left as follow diagram.
①Screw cover
②Screw
③Handle part
④Cover-screw cap
Warning！
When changing the side at which the door
opens, the appliance must not be
connected to the mains. Remove plug
from the mains beforehand.

To activate the Quick Freeze function, press
the Quick Freeze button until the icon light is
lit. The temperature is then set to -24°C (-
11°F)
Quick Freeze mode automatically exits after
about 52 hours.
To deactivate the Quick Freeze mode, press
button until the light goes off and the
refrigerator temperature setting will revert to
the previous setting.
4. Eco Mode
If you are going to be away for a long period
of time, you can turn it to Eco mode to
maintain a cooling temperature but save on
electricity.
Ensure the freezer is unlocked by checking
that there is no light on ECO (Lock old). If
the light is on, press and hold for 3 seconds.
To activate Eco Mode, press the button until
the light is lit. The temperature is set to -17°C
(1°F).
To deactivate Eco Mode, press the button
until the light goes off. The freezer
temperature setting will revert to the previous
setting.
5. Child Lock
You can lock the controls of the refrigerator.
●
The Child Lock is automatically turned on.
To deactivate the child lock, press and hold
the button for 3 seconds until the light goes
off. Now you can change the other functions
of the freezer.
If no button has been pressed for 20 seconds,
the light will be on.
6. Alarm
If the door has been left open for over 2
minutes, then the door alarm will sound & the
control panel will show “dr”. The icon will
flash and there will be buzzing sound.
If the door is not closed, the buzzer will sound
3 times every 1 min.
After the door alarm time exceeds more than
10 minutes, the buzzer stops beeping, the icon
is off, and the display screen shows normal.
The door alarm can also be cleared by closing
the door.
To save energy, please avoid keeping the
door open for a long time when using the
appliance.
ELECTRONIC CONTROLS

FEATURES OF THE FREEZER
Your appliance has the accessories as shown in the “Description of the appliance”. We recommend
that you read through the below carefully before using the appliance to prevent damage to the
product
1. Shelves in the Freezer Cabinet
The glass shelves in the refrigerator can be taken out to adjust their position and to be cleaned.
To remove tilt the front of the shelf upwards and gently slide out.
To replace hold the shelf straight with the fridge cavity angling the shelf downward. Slide the shelf
in on the shelf runner and gently drop into place.
●
2. Freezer Drawer
●
The Freezer drawers are used store food which needs to be frozen including meat fish ice cream
etc.
To remove tilt the front of the drawer upwards and gently slide out.
To replace hold the drawer straight with the fridge cavity angling the drawer downward. Slide the
drawer in on the shelf runner and gently drop into place.
FEATURES OF THE FREEZER