Westinghouse LVM-47w1 User manual

(_Westinghouse
USER'SMANUAL
MANUELDEL'UTILISATEUR
MANUALDELUSUARIO
LVM-42w2/LVM-47w1
1080p Monitor
Moniteur 1080p
Monitorde 1080p
I ° I

Contents
Important Product Safety Instructions ........................................ 2
Safety Guidelines .................................................................. 4
Cleaning the HD Video Monitor ................................................. 5
INSTALLATION
Package Contents ................................................................. 6
Front View of the HD Video Monitor .......................................... 7
Rear View of the HD Video Monitor ........................................... 7
Side View of the HD Video Monitor ............................................ 8
Remote Control ................................................................... 10
Installation .......................................................................... 11
OSD Functions
PICTURE PARAMETERS: Brightness /Contrast /Saturation /Hue /
Color Temp /Sharpness /Aspect Ratio /
Backlight /Reset ................................. 15
PC PARAMETERS: Auto Adjust /Clock /Phase /Position .................. 16
AUDIO SETTINGS: Volume /Bass /Treble /Balance /Mute /Speaker/
Reset ........................................................ 17
PICTURE-IN-PICTURE: Display Mode /Main Source /PIP Source /
Swap /PIP Position /PIP Size /Audio From ..... 18
GENERAL SETTINGS: Menu Position /Menu Timeout /Language /
Sleep Timer /Transparency /DPMS /LED /
System Info /Factory Reset .......................... 19
Specifications
Specifications .................................................................. 20
Troubleshooting
Troubleshooting ................................................................ 21

Explanations of required symbols :
SYM BOL SYMBOL DEFIN ITION
SA 1965
SA 1966
DANGEROUS VOLTAGE :
The lightning flash with arrowhead symbol, inside an equiiaterat
triangle, is intended to alert the user to the presence of
uninsuiated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of
electrical shack to persons,
iNSTRUCTiONS :
The exeiaraation point inside an equilateral triangle is intended
to ale_ the user to the presence af important operating end
maintenance ( servicing ) instructions in the literature
accompanying the appliance.

Important Product Safety Instructions
Follow and obey all warnings and instructions marked on the HD Video Monitor. For your
safety, please read all the safety and operating instructions before you operate the HD
Monitor Keep this user's manual for future reference.
Overloading
Do not overload wall outlets, extension cords, or power strips. This can result in fire or
electronic shock.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. Periodically inspect the cords and each end of the
cords for damage. The HD Monitor shall be installed near a wall socket outlet and the plug
on power cord shall be readily accessible.
Ventilation
Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable
operation of the HD Monitor and to protect it from overheating, these openings must not be
blocked or covered.
•Do not block the openings by placing the HD Monitor on a bed, sofa, rug or other
similar surface.
• Do not place the HD Monitor in a built-in installation such as a bookcase or rack
unless proper ventilation is provided and the manufacturer's instruction have been
adhered to.
Other Notices
Avoid exposing the HD Monitor to direct sunlight or high temperatures.
Avoid exposing the HD Monitor to moisture or high humidity.
Do not attempt repairs yourself. Your warranty does not cover repairs or attempted
repairs by anyone not authorized by Westinghouse Digital.
If the HD Monitor will not be used for a long period of time, unplug the HD Monitor and
remove the batteries from the remote control.
Precautions
• Avoid touching the screen. Skin oils are difficult to remove.
• Never remove the rear cover. The HD Monitor contains high-voltage parts. You may
be seriously injured if you touch them.
• Avoid exposing the HD Monitor to direct sunlight or another heat source. Orient the
HD Monitor away from direct sunlight to reduce glare.
• Always handle the HD display with care when moving it.
• Place the HD Monitor in a well-ventilated area; don't place the HD Monitor in airtight
compartments. Do not place anything on the HD Monitor that prevents heat
dissipation.
• Ensure that the area around the HD Monitor is clean and free of moisture.
• Do not place heavy objects on the HD Monitor, audio/video cables, or power cord.
• If the HD Monitor emits smoke, abnormal noise, or a strange odor, immediately turn it
off and contact the Westinghouse Service Center.
WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose The
HD Monitor To Rain Or Moisture! The HD Monitor shall not be exposed to dripping
or splashing and objects filled with liquids, such as vases, shall not be placed on the
Monitor.
2

1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use the HD Monitor near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not attempt to bypass the safety purpose of the polarized or grounding- type plug.
A polarized plug has two blades with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. If the provided plug does not fit into
your wall outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at the ends of
the cord.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the HD Monitor. When a cart is used, use caution when moving the cart
to avoid injury or damage.
13) Unplug the HD Monitor during lightning storms or when it is not being used fora long
period of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the HD
Monitor has been damaged in any way, such as the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the HD Monitor, it has
been exposed to rain or moisture, it does not operate normally, or the TV has been
dropped.
Antenna Installation Safety
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the HD Monitor, be sure the antenna or cable
system is grounded to prevent voltage surges and built-up static charges. Article 810 of the National
Electrical Code, ANS/NFPA 70, provides information on proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
Lightning
For added protection for the HD Monitor during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the HD Monitor due to lightning and power-line surges. Do not
disconnect the antenna or the power cord during a heavy storm - lightning may strike while you are
holding the cable cord, causing serious injury. Turn off your HD MONITOR and wait for the weather
to improve.
Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits. When installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits.

Safety Guidelines
CAUTION: The power supply outlet should be located near the HD Monitor and should be easily accessible.
Always use the appropriate AC cord that is certified for your specific country. Some examples are listed below:
USA.................. UL Switzerland ..... SEV
Canada ............. CSA Britain .............. BASE/BS
Germany .......... VDE Japan ............... Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The specific power cord for this HD Monitor is enclosed and has been selected according to the country of
destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace
the original cord set, or if the cord set is not enclosed. The female receptacle of the cord set must meet
IEC-60320 requirements and should look like Figure A1 below:
Figure AI[_ Figure A2@_.
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA Labeled.
For LCD Monitors that are placed on a desk or table, type SVT or SJT cord sets may be used. For LCD
Monitors placed directly on the floor, only SJT type cord sets may be used. The cord set must be selected
according to the current rating for the LCD Monitor. Please consult the table below for the selection criteria for
power cords used in the United States and Canada.
Cord Type Size of Conductors in Cord Maximum Current Rating of Unit
18 AWG 10 Amps
SJT 16 AWG 12 Amps
14 AWG 12 Amps
18 AWG 10 Amps
SVT 17 AWG 12 Amps
FCC Compliance Statement
This equipment has been tested and complies with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy, and may
cause harmful interference to radio communications if not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the LCD Monitor and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the Westinghouse Service Center or an experienced radio/Monitor technician for assistance.
FCC Warninq
To assure continued FCC compliance, the user must use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. If a BNC cable is used, use only a
shielded BNC (5) cable. Also, any unauthorized changes or modifications not expressly approved by
Westinghouse Digital will void the user's authority to operate this device.
4

Cleaning the HD Video Monitor
•MAKE SURE THE HD Monitor IS TURNED OFF
•NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner
onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-
abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
Westinghouse Digital does not recommend the use of any ammonia or alcohol-based cleaners on
the HD Monitor screen or case. Some chemical cleaners have been reported to damage the screen
and/or HD Monitor case. Westinghouse Digital will not be liable for damage resulting from the use of
any ammonia or alcohol-based cleaners.

INSTALLATION
Package Contents
Your product package includes:
• LVM-42w2 (42") /LVM47-w1 (47") Westinghouse HD Video Monitor
• Remote Control (with batteries)
• Power Cord
• Quick Connect Guide
• User's Manual
• Warranty Card

Front View of the HD Video Monitor
Use the buttons on the right side of the HD Monitor or on the remote control to display the On
Screen Display (OSD). The OSD controls are defined in "OSD Functions" on page 12.
Speakers
Rear View of the liD Video Monitor
"IR" receiver and
LED indicator

Side View of the HD Video Monitor

5
14
16
Side View of the HD Video Monitor
1. DVI2 (Supports up to 1080p Full HD)
Using a 20-pin DVI cabte, connect to a computer. HD Digital cable/satellite
1 receiver. HD Set-Top-Box. DVD or other device with a DVI output.
2. DVl2 Audio Input (Right /Left)
Connect an external DVI audio source to this jack.
2 3. HDMI Input
Connect to an external video device such as HD Digital cable/satellite
receiver. HD Set-Top-Box. Media Center PC. or DVD player.
3 4. HDMI Audio Input (Right /Left}
Connect the audio input if you using a DVI-to-HDMI converter.
5. S-Video Input
Connect to an external video device such as a VHS player.
46. AV Video Input
6 Connect to an external video device such as a VHS player or video game
system.
7. AV & S-Video Audio Input (Right/Left)
Connect an external audio source to this jack; (Audio (R/L). This connection
8 supports either S-Video or AV in put.
8. Audio Output (Right /Left)
Connect this output to an external stereo audio amplifier, receiver or
surround sound processor.
9 9. VGA Audio IN
Using the cable provided, connect to the Audio out (Green) from a corn puter.
10 10. VGA
Using a 15-pin VGA cable, connect to a computer or other device with a
VGA output.
11. DVll Audio Input (Right/Left)
11 Connect an external DVI audio source to this jack.
• DVI1 (Supports up to 1080p Full HD)
Using a 20-pin DVI cable, connect to a computer, HD Digital cable/satellite
receiver. HD Set-Top-Box, DVD or other device with a DVI output.
12 13. YPbPrl (HD) Input
Connect an external video device such as DVD or video game system with
component output to these jacks.
14. YPbPr2 (HD) Input
13 Connect an external video device such as DVD or video game system with
component output to these jacks.
15. YPbPrl Audio 1 Input (Left/Right)
Connect an external audio source to this jack.
15 16. YPbPr2 Audio 2 Input (Left /Right)
Connect an external audio source to this jack.
17. AC IN (Power}
Connect the power cord from AC IN to a power source.

Remote Control
The Remote Control will transmit to the HD Monitor up to 10 feet away.
1. POWER:
Switch the power On/Off
2. INPUT
Select input source
3. OSD SUB-MENU SELECTION
Select OSD sub-menu option directly
4. PREVIOUS OSD MENU
Select previous OSD menu
5. MENU/EXIT
Turn OSD Menu On/Off.
6. SCALING
Select Video Display format "STANDARD" or
"FILL"
7. V/A/41/_
OSD MENU control
8. Enter
Execute a command
9. MUTE
Turn the Sound On/Off
10.1NFO
Display the source and channel information
11.PIP
Display sub-picture On/Off
12. FREEZE
Freeze main screen
13.VOL - /+
Volume Up/Down adjustment
14.SOURCE •/•
Source selection Up/Down
15.YPbPr
Select YPbPrl /YPbPr2 source input
16. VGA
Select VGA source input
11. DVI
Select DVll /DVl2 /HDMI source input
18. S-Video
Select S-Video source input
19.AV
Select AV source input
1
!
1
1
2
7
4
6
8
t0
12
14
10

Installation
1, Insert Remote Control Batteries
1) Remove the battery cover.
2) Insert the batteries corresponding to the (+) and (-) marks on the battery
compartment.
3) Re-attach the battery cover.
CAUTION:
• Only use AAA batteries,
•Do not mix new and old batteries, This may result in cracking or leakage, which
may pose a fire risk or lead to personal injury,
•Insert batteries according to (+) and (-) markings, Inserting the batteries incorrectly
may result in cracking or leakage, which may pose a fire risk or lead to personal injury,
•Dispose of used batteries in accordance with local laws and regulations,
•Keep batteries away from children and pets,
•When the remote control will not to be used for an extended period, remove the batteries,
11

2. Connect audio and video cables from a PC
Connect one or all of the following into the back of the HD Monitor
IMPORTANT: Before beginning, make sure all devices are turned off.
VGA CONNECTION: Connect an analog VGA cable from your PC VGA OUT port to
the HD Monitor VGA IN port.
DVII/DVI2 CONNECTION: Connect a Digital DVI cable from your PC DVI OUT port to
one of the HD Monitor DVI-HDCP port.
AUDIO CONNECTION" Connect a stereo mini cable from the PC's AUDIO OUT port
to the AUDIO IN port on the HD Monitor.
3. Connect AV, Component, S-Video to Video Devices
Connect Audio/Video cables from compatible devices to the back panel of the HD
Monitor.
ii_i_i_;/_ ¸ iiiiiiii/
12

4. Connect power cables
Connect the power cord to the HD Monitor then to a properly grounded AC outlet.
5. Turn Power On
Press the Power ON button on the right side of the HD Monitor, or press the Power ON
(Red) button on the remote control.
Power Button
6. Select input source for the HD Monitor using the OSD menu or remote
control
7. If connecting to a PC (VGA/DVI1/DVI2):
For the best picture quality, set the HD Monitor resolution to 1920 x 1080 at 60Hz (refer
to the graphic card's user guide to set this resolution).
13

OSD Function
All the OSD function settings are controlled either by the remote control or using the control
keys on the right side of HD Monitor.
To display the OSD main menu, press the Menu button on the right side of front control keys
of the HD Monitor or the MENU key on the remote control. Use _ /_ arrow keys to highlight
the desired OSD sub-menu.
Main Menu
To select a sub-menu, press • /v on the right side of the HD Monitor or the • /v key on the
remote control. Also, by using the number keys on the remote control, you can select a OSD
sub-menu directly.
14

PICTURE PARAMETERS:
Function Name Function
................................................................................................. i............................................................................................................................................................................................................................................................................................................
Brightness Brightness adjustment
Contrast Contrast adjustment
Saturation Saturation adjustment
Hue Hue adjustment
Color Temp Color temperature adjustment (Warm, Neutral, Cool)
Sharpness adjustment
Sharpness (Sharpness cannot be adjusted in PC mode)
Aspect Ratio Set display to "STANDARD" /"FILL"
Backlight Backlight adjustment
Reset Reset video settings
15

PC PARAMETERS:
Function Name Function ....
Auto Adjust Automatically adjust the horizontal phase of the image
Clock Clock adjustment
Phase Phase adjustment
Position Adjust the horizontal and vertical position of the image
NOTE: The GRAPHIC menu is only available when VGA source is selected.
16

AUDIO SETTINGS:
Function Name I Function
Volume Volume adjustment
Bass Bass adjustment
Treble Treble adjustment
Balance Balance adjustment
Mute Select Audio OFF or ON
Speaker Select internal or external speaker
Reset Reset audio settings
17

PICTURE-IN-PICTURE:
Function Name Function
Display Mode OFF --> PIP --> PBP --> POP
Main Source Select main screen sources
VGA --> DVI1--> DVI2 --> AV --> S-Video--> YPbPrl -->
YPbPr2--> HDMI
PIP Source Select sub screen sources
Please see PIP/PBP/POP specification in Table 1
Swap Swap main screen and sub-screen source
PIP Position Sub-screen display horizontal/vertical position adjustment
Sub-screen display size adjustment
PIP Size (Small-->Medium --> Large)
Audio From Select main screen or sub-screen audio sources
Table 1:
VGA DVll AV S-Video YPbPrl YPbPr2 DVl2 HDMI
VGA X O O OX X OO
DVll O X O O O O O O
AV O O X X O O O O
S-Video O O X X O O O O
YPbPrl X O O O X X O O
YPbPr2 X O O O X X O O
DVl2 O O O O O O X X
HDMI O O O O O O X X
18