Whistler PRO-3450 User manual

Installation
Instructions
Pro-3450
Laser/Radar Detectors
THE WHISTLER GROUP, INC.
CORPORATE HEADQUARTERS
13016 N. Walton Blvd.
Bentonville, AR 72712
TEL [phone] FX [phone]
www.whistlergroup.com
P/N 202882, © WHISTLER 2004 www.whistlergroup.com
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 1

TABLE OF CONTENTS
2
Topic Page
Tools Required 1
Whistler Pro-3450 Components 3
Mounting Brackets 4
Mounting Fasteners 5 - 6
Installation of Radar Antenna 7 - 11
Installation of Temperature Probe 11
Installation of Laser Antenna 12 - 13
Installation of Control Panel 14 - 16
Optional Accessories 17
Troubleshooting Guide 18
TOOLS REQUIRES
Tools Required For Installation
•Phillips or Blade Screwdriver
•3/8" Open End Wrench
•Electric Drill
•Drill Bit: 13/64", 5/16”. 7/64”, 9/64”, and 13/64”
•Other Tools May Be Required Based On Your Vehicle Type Or
Requirements For Customized Installation
Dimensions:
• Control Panel: .8” H x 2.8” W x 2.3” L
• Radar Antenna: 1.4” H x 4.0” W x 3.6” L
• Laser Antenna: 1.9” H x .9” W x .7” L
Cable Lengths:
• Radar Antenna Cable: 3”
• Laser Antenna Cable: 9’
• Power Cable: 4’
• Interconnecting Cable: 20’
Specifications are subject to change without notice.
1
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 3

INTRODUCTION
MOUNTING BRACKETS
4
WHISTLER Pro-3450 COMPONENTS
3
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 5

MOUNTING FASTENERS
6
MOUNTING FASTENERS
5
Reference Description/Use Qty
ABolt #10-32 x 1-1/4" 2
• Fastens Large L or Small L
Bracket to vehicle support.
BBolt #10-32 x 1/2" 2
• Fastens Small L to Large L
Bracket (optional approach).
CNut #10-32 4
• Use with #10-32 bolts.
DLock Washer 4
• Use with #10-32 bolts.
EFlat Washer 2
• Use with #10-32 bolts.
FSheetmetal Screw #6 x 3/4" 7
• Fastens Large L/Small L Bracket
or 45° Reflector to radar antenna.
Mounts Temp. Probe
GSheetmetal Screw #4 x 5/8" 2
• Fastens hanging bracket
to interior vehicle surface.
HHook & Loop 1/2” x 1” 1
• Fastens LRM-5 to back
of rearview mirror when
windshield bracket is not used.
IMounting Cable Tie 1
• Secures cable from radar
antenna at various locations
in engine compartment.
J4" Cable Tie 5
• Secures cable from radar
antenna at various locations in
or under the vehicle.
KInterface Cable 1
• Connects the radar antenna
to inside control panel
Note: If mounting fasteners are missing from your package,
please call 1-800-531-0004 for replacements.
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 7

INSTALLATION OF RADAR ANTENNA
8
INSTALLATION OF RADAR ANTENNA
7
General Information
The radar antenna is waterproof and designed to be mounted
at the front of your vehicle. In most vehicles the best mounting
location is directly below or behind the bumper. Radar signals
will pass through non-metallic materials such as fiberglass and
plastic, however, be sure to mount the receiver away from any
metal, as it will block the recei v e r ’s antenna. Because the optimal
location for mounting the antenna varies by vehicle type, the
hard w a re supplied is designed to offer a wide variety of mounting
options. We suggest choosing the option that enables the
antenna to be securely fastened and provides the antenna win-
dow adequate rearward visibility.
NOTE: The “antenna” is the bubble area on the case. All
re f erences to antenna in this manual will be the bubble area.
NOTE: Use of hard w a r e that is not supplied or DRILLING
into the case will cause damage to the receiver and void the warr a nty.
Antenna Mounting Brackets
There are two types of mounting brackets for the antenna:
Large L (1) and Small L (2). The Large L bracket fastens to the
through the hole on the flange of the antenna and then tight-
en into the metal bracket (do not over tighten). The Large L
Bracket may be fastened to the antenna in a variety of posi-
tions as shown on page 8.
Do not drill into the receiver housing!
This arrangement provides flexibility for fastening the anten-
na/bracket assembly to your vehicle in a manner that allows the
antenna window (ANTENNA) to have a forward looking view of
the road ahead.
The Small L Brackets (2) may also be fastened to the antenna in
different positions as shown below:
Use one #6 x 3/4" screw to fasten each Small L Bracket to the
antenna. Again, do not over tighten the screws.
In some situations it may be advantageous to use both the
Large Land Small L Brackets to install the antenna in a vehicle.
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 9

10
INSTALLATION OF RADAR ANTENNA
9
The Small L Brackets are fastened to the Large L Bracket using
the #10-32 x 1/2" bolts, #10-32 nuts and lock washers.
To fasten the Large L or Small L Brackets to your vehicle, mark
the supporting structure through the appropriate holes in the
brackets, then drill the holes in the supporting structure with a
13/64" drill bit. Attach the bracket(s) to the supporting struc-
ture using two bolts (#10-32 x 1-1/4") and corresponding nuts,
flat washers, and lock washers. You may also use 2 #6 sheet
metal screws. Because rough road surfaces can cause excessive
vibration or bouncing, be certain to fasten the bracket(s)
securely to your vehicle.
Horizontal Or Vertical Mounting Of Antenna
The antenna can be attached to the vehicle in a horizontal or
vertical position, or at any angle between these two points.
Select the position that allows you to fasten the antenna to
your vehicle in the most secure manner
Horizontal Mounting
When mounting the antenna in a horizontal position (or on an
angle between), remember to keep the ANTENNA window as
close to perpendicular as possible to the road surface (ANTEN-
NA window should not be angled up toward the sky or down
toward the road surface).
Mounting Vertical (with 45º Reflector)
For vehicles that do not have sufficient clearance behind the
bumper (about 5") to mount the antenna in a horizontal posi-
tion, the 45º. Reflector should be used.
The 45º Reflector is attached to the antenna with two screws (#6
x 3/4") on the side of the antenna housing marked ANTENNA.
Slide the screws through the corner holes on the flange of the
antenna housing and then tighten into the metal reflector (do
not over tighten).
INSTALLATION OF RADAR ANTENNA
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 11

Mount the antenna to the vehicle such that the ANTENNA
window is facing the road surface, sky, right or left of the
vehicle, and the reflector has an unobstructed view of the
road ahead.
Mounted in this position, radar signals are reflected into the
ANTENNA window.
Mounting the Temperature Probe
Find a location that is far enough away from the engine and
radiator heat but still in the airflow for the vehicle. Mounting
the Probe too close to these heat areas will give a false high
temperature.
• Attach the mountable tie wrap (supplied) to the
Temperature Probe as shown.
• Mark location for Probe, then drill a hole using a 7/64” drill
bit. Attach Probe with tie wrap in the correct orientation
using the #6 x 3/4 screws.
NOTE: Mount the Probe so that there is space between the
Probe and the mounting area.
Do not mount Probe directly to metal area.
11
Antenna Cable to the Control Panel
Once the antenna is installed connect the cable from the
radar antenna to quick disconnect interface cable. Tie this
cable in knot similar to using an electrical extension cord.
Run the cable along the edge of the engine compartment to
the firewall. Find a location in the firewall where other wires
(or the speedometer cable) enter the passenger compartment
and feed the stereo jack connection through. Be careful not
to interfere with or disconnect other wires, cables, or mechanical sys-
tems of your vehicle while routing the antenna cable. Also,
keep the antenna cable away from any areas in the engine
compartment that may become hot. Cable ties are provided
to secure the antenna and Temperature Probe cables at vari-
ous points in the engine compartment.
General Laser Information
The laser antenna provides both front and rear laser re c e p t i o n .
Mount the laser antenna with the 3-lens array facing forward
(down the road) and the single lens facing behind. This approach
offers the greatest protection, since you will most often be
traveling into a laser signal, rather that away from it when laser
speed enforcement is encountered. For effective protection,
make sure the laser antenna has an unobstructed view forw a rd
and behind, and that it is not placed behind metallic sun scre e n s .
Mounting the Laser Antenna
The laser antenna can be mounted to the front windshield
using the windshield bracket supplied.
12
INSTALLATIONofLASERANTENNAINSTALLATION OF RADAR ANTENNA
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 13

13
Installing the Laser Antenna
Before using, attach the suction cup and rubber bumpers (2)
to the metal bracket. If necessary, you may bend the metal
brack e t in order to position the laser antenna correctly (3-lens
a rray facing f o rw a rd, single lens facing behind.)
Laser antenna mounted with windshield bracket.
Using Hook & Loop Fasteners, the laser antenna may also be
mounted to the back side of your rearview mirror. Be careful not
to block the rear facing lens when mounted in this manner.
Also, clean the appropriate surfaces with isopropyl alcohol before
adhering the adhesive side of the fastener to those surfaces.
Laser antenna mounted to rearview mirror with Hook & Loop Fasteners.
INSTALLATIONOFLASERANTENNA INSTALLATIONOFCONTROLPANEL
14
General Information
The control panel may be mounted using the Under Dash
Bracket or Hook & Loop fastener supplied. As an alternative, you
may also use a Through Dash Bracket. When choosing a mounting
location, consider your needs for ease of viewing the display,
accessibility of controls (remember Mute Mode may be used
frequently), and concealment.
The Pro-3450 can also be mounted on its side and even upside
down! Installation just got a lot easier.
Control Panel Mounted With Under Dash Bracket
Fasten the Under Dash Bracket to your vehicle’s dash with the
two #4 x 5/8" sheet metal screws provided. A 5/64” drill bit
should be used to drill pilot holes for the screws. Use the holes in
the bracket to mark the location for pilot holes.
Once the bracket is fastened to your vehicle, the control panel
can be attached to it. However, we suggest connecting all cables
to the back of the control panel before snapping it into the bracket.
See page 15 for proper placement of cables.
Control panel snaps into rather than slides onto the Under Dash Bracket.
HIGHWAY
HIGHWAY
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 15

INSTALLATIONOFCONTROLPANEL
Control Panel Mounted With Hook & Loop Fasteners
Fasteners can be used to mount the top or bottom of the control
panel to your vehicle. Before adhering the adhesive side of the
fastener to a surface, clean that surface with isopropyl alcohol.
Use of Hook & Loop simplifies control panel installation.
Control Panel Mounted With Through Dash Bracket
Installation instructions are provided with the bracket. We
recommend using a professional installer if you are not familiar
with customized dashboard installations.
15
1. Power Port
2. Radar Port
3. Laser Port
4. Voice Port
5. Laser Port
Antenna Cable Connection
The stereo connector on the end of the antenna cable plugs
into Radar port (2) on the back of the control panel.
Laser Antenna Cable Connection
After mounting the laser antenna conceal the cable and plug
the stereo jack connector into the port on the back of the con-
trol panel labeled LASER port (3).
Power Cable Connection
The power cable has a plug on one end which connects to the
back of the control panel at the port labeled PWR port (1). At
the other end of the power cable the power and ground wires
are separated. The ground wire has a “U” type connector w h i c h
should be fastened to a metal surface. Look for an existing
screw or bolt under the dash to use as a grounding point. The
power wire has a spade type connector which should be connected
to a switched +12 volt DC circuit in your vehicle’s fuse box. A
switched circuit is one that has power when your vehicle is on,
but has no power when your vehicle is off. Connect the “U”
type connector to the ground point selected, attach the power
cord plug to the control panel area marked “PWR” then touch
the power wire to the +12 volt DC switched power source
selected; if the control panel sounds the self test sequence,
then all connections are correct.
INSTALLATIONOFCONTROLPANEL
16
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 17

17 18
PROBLEM: No display or audio.
•Check fuse in power cable, replace if necessary.
•Check fuse in fuse box, replace if necessary.
•Make sure power cable is properly grounded.
PROBLEM: Unit alarms when using vehicle equipment or
electrical accessories (brakes, power mirrors/windows,
directionals, horn, etc.)
•Check condition of vehicle’s electrical system, including
battery and alternator.
• Install a filter capacitor (470mfd. 25 volt or larger
capacitor value) where power connection is made.
PROBLEM: Audio alerts are not loud enough.
•Cancel Auto Quiet Mode or City Mode
•Check audio level settings.
PROBLEM: Display shows R error.
• Warning communicates “loss of link” between
control panel and front antenna (RADAR).
•Check antenna connection at back of control panel.
•Contact factory, if you suspect antenna is defective.
•Look for cuts in the cable
If difficulties occur which cannot be solved by information in this
Troubleshooting Guide, please call Whistler Customer Service at
1-800-531-0004 or visit our FAQ page at ww w. w h i st l e r g ro u p . c o m ,
be f ore returning your unit for serv i ce.
For warranty information, re f e r to owner’s manual.
TROUBLESHOOTINGDE
Added Protection From Behind/Optional Rear Laser Module
For drivers interested in gaining increased detection range when laser
is transmitted from behind,the Pro-3450 canbe upgradedwith a second
laser antenna. This antenna is mounted facing forwa rd and can be
pu rchased from many Whistler retailers or directly from Whistler; ask
for the Part Number 202895.
The Pro-3450 control panel is designed to operate with an additional
laser receiver; the laser 2 port (5) is the input forthe optional laser rec eiver.
An asterisk is displayed next to the Band ID (LASER) when laser signals
are detected.
More Volume/Voice Module
Real Voice Module (P/N Pro-3450VM) can be used to articulate Band ID,
Safety Wa rning and Feature Selection. Plugs into V O I C E p o r t (4).
NOTE: This is the only audio option that can be plugged into the
Pro-3450. Any otherdevice may damage the unit and void the warr anty.
OPTIONAL ACCESSORIES
The following accessories can be ordered directly from Whistler by calling
1-800-531-0004 or visit our online store at www.whistlergroup.com
Order Code Description Price
Pro-3450VM Voice Module $ 79.95
202895 Optional Rear Laser Module Call for
Pricing
Shipping and handling (per order) $5.00 Prices are subject to change without notice.
Pro3450INSTALLmanual.pdf 3/15/04 3:18 PM Page 19